change time Peugeot 208 2019 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2019, Model line: 208, Model: Peugeot 208 2019Pages: 263, PDF Size: 9.61 MB
Page 8 of 263
6
As a passenger, if you avoid connecting your
m ultimedia devices (film, music, video game,
etc.), you will contribute towards limiting the
consumption of electrical energy, and so of
fuel.
Disconnect your portable devices before
leaving the vehicle.
Eco- driving
Optimise the use of your
gearbox
With a manual gearbox, move off gently
a nd change up without waiting. When
accelerating, change up early.
With an automatic gearbox, give preference
to automatic mode and avoid pressing the
accelerator pedal heavily or suddenly.
The gear shift indicator invites you to engage
the most suitable gear: as soon as the
indication is displayed in the instrument panel,
follow it straight away.
For vehicles fitted with an automatic gearbox,
this indicator appears only in manual mode.
Drive smoothly
Maintain a safe distance between vehicles,
u se engine braking rather than the
brake pedal, and press the accelerator
progressively. These practices contribute
towards a
reduction in fuel consumption and
CO
2 emissions and also help reduce the
b
ackground traffic noise.
If your vehicle has cruise control, make use of
the system at speeds above 25
mph (40 km/h)
when the traffic is flowing well.
Control the use of your electrical
equipment
Before moving off, if the passenger
compartment is too warm, ventilate it by
opening the windows and air vents before
using the air conditioning.
Above 31
mph (50 km/h), close the windows
and leave the air vents open.
Consider using equipment that can help
keep the temperature in the passenger
compartment down (sunroof blind and window
blinds, etc.). Switch off the headlamps and front foglamps
when the ambient light level does not require
their use.
Avoid running the engine before moving off,
particularly in winter; your vehicle will warm up
much faster while driving. Switch off the air conditioning, unless it has
automatic regulation, as soon as the desired
temperature is attained.
Switch off the demisting and defrosting
controls when not required, if they are not
automatically controlled.
Switch off the heated seat as soon as
possible.
Eco-driving is a
range of everyday practices that allow the motorist to optimise their fuel consumption and CO
2 emissions.
Eco-driving
Page 11 of 263
9
Trip distance recorder (miles
o r k m).
Engine oil level indicator
(depending on version).
Gear shift indicator with
a
manual gearbox.
Selector position and gear
with an automatic gearbox.
Digital speedometer (mph or
km/h).
Displaying/hiding the digital speedometer
(Depending on version)
Cruise control settings.
Speed limiter settings.
Service indicator.
Total distance recorder (miles
o r k m). Hold this button down.
"- -" or "0" is displayed.
Press this button to display or
hide the digital speedometer.Displays
Trip computer
Stop & Start time counter.
Remaining driving range.
Current or average fuel consumption.
Average speed of the vehicle.
Distance travelled by the vehicle.
Gearbox
Park.
Reverse.
Neutral.
Automatic mode (Drive).
Sequential mode.
Change up/down a
gear.
1
Instruments
Page 27 of 263
25
Permanent display:
F Sel ect the " Applications " menu, then the
" Vehicle apps " tab, then "Trip computer ".
The trip computer information is displayed in
tabs.
F
P
ress one of the buttons to display the
desired tab.
Temporar y display in a
specific window:
F
P
ress the end of the wiper control stalk
to access the information and display the
different tabs.
The current information tab with:
-
T
he range.
-
T
he current fuel consumption.
-
T
he Stop & Start time counter.
The trip " 1" tab with:
-
T
he average speed for the first trip.
-
T
he average fuel consumption.
-
T
he distance travelled.
The trip " 2" tab with:
-
T
he average speed for the second trip.
-
T
he average fuel consumption.
-
T
he distance travelled.Trip reset
F When the desired trip is displayed, press the reset button or on the end of the wiper
control stalk.
Tr i p s " 1" and " 2" are independent and are used
identically.
For example, trip " 1" can be used for daily
figures and trip " 2" for monthly figures.
A few definitions
Range
(miles or km)
The distance which can still be
travelled with the fuel remaining in
the tank (related to the average fuel
consumption over the last few miles
(kilometres) travelled).
This value may fluctuate if a
change
of driving style or terrain results in
a
significant change in the current fuel
consumption.
Dashes are displayed when the range falls
below 19
miles (30 km).
After filling with at least 5
litres of fuel, the
range is recalculated and is displayed if it
exceeds 60
miles (100 km).
If dashes instead of figures continue
to be displayed when driving, contact
a PEUGEOT dealer or a qualified workshop.
Current fuel consumption
(mpg or l/100 km or km/l)
C alculated over the last few seconds.
1
Instruments
Page 28 of 263
26
This function is only displayed from
19 mph (30 km/h).
Average fuel consumption
(mpg or l/100 km or km/l)
C alculated since the last trip computer
reset.
Distance travelled
(miles or km)
Calculated since the last trip computer
reset.
Average speed
(mph or km/h) Calculated since the last trip
computer reset.
Total time in stop mode
(minutes/seconds or hours/minutes)
If your vehicle is fitted with Stop & Start, a time
counter adds up the time spent in STOP mode
during a
journey.
It resets to zero every time the ignition is
switched on.
Setting the time and date
Instrument panel
F Each press of this button toggles between the following settings:
-
h o u r,
-
minutes,
-
1
2 or 24 hour format.
With PEUGEOT Connect
Radio
F Select the Settings menu in
the upper banner of the touch
screen.
F
Sel
ect " System configuration ".
F
Sel
ect "Date and time ".
F
Sel
ect " Date " or "Time ".
F
C
hoose the display formats.
F
C
hange the date and/or time using the
numeric keypad.
F
C
onfirm with " OK".
With PEUGEOT Connect
Nav
Setting of the time and date is only available if
synchronisation with the GPS is deactivated.
F
Sel
ect the "Settings " menu.
F
P
ress the " OPTIONS " button to go to the
secondary page.
F
Sel
ect "Setting the time- date".
F
Sel
ect the " Date" or " Time" tab.
F
A
djust the date and time using the numeric
keypad and confirm.
F
I
n the selected tab, press this
key to confirm.
Additional settings
You can choose:
- T o change the date format (DD/MM/ Y Y Y Y,
YYYY/MM/DD, etc.)
-
T
o change the time format (12h/24h).
-
T
o change the time zone.
-
T
o activate or deactivate synchronisation
with the GPS (UTC).
Instruments
Page 29 of 263
27
The system does not automatically
manage the change between winter and
summer time (depending on country).
The change between winter and summer
time is done by changing the time zone.
Lighting dimmer
System for the manual adjustment of the
brightness of the instrument panel and the
touch screen to suit the ambient light level.
With two buttons
Lighting switched on:F
P
ress this button to raise
the level of brightness.
F
P
ress this button to lower
it.
Release the button once the desired level of
brightness is reached.
With one button
F Press this button to adjust the brightness.
F
R
elease the button once the desired level
of brightness is reached.
When the vehicle lighting is off, or in day
mode (daytime running lamps on), pressing
the button does not have any effect.
With touch screen
The brightness can be adjusted differently
for day mode (lighting control stalk in
position " 0") and night mode (lighting
control stalk in any other position).
F
I
n the Settings menu, select " Brightness".
F
A
djust the brightness by pressing the
arrows or moving the slider.
1
Instruments
Page 63 of 263
61
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBFD)
The fixed illumination of this warning
lamp indicates that there is a fault
with the ABS.
The vehicle retains conventional braking. Drive
carefully at moderate speed. If these warning lamps come on,
accompanied by an audible signal
and a
message, this indicates a fault
with the electronic brake force
distribution (EBFD) system.
When changing wheels (tyres and rims),
ensure that these are approved for your
vehicle.
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal. If you need to brake in an emergency,
press the brake pedal ver y firmly and
keep the pressure applied.
You must stop as soon as it is safe to do so.
In both cases, have the system checked by
a
PEUGEOT dealer or a qualified workshop as
soon as possible.Anti-slip regulation (ASR)/
Dynamic stability control
(DSC)
Operation
These systems are activated automatically
every time the vehicle is started.
They come into operation in the event of
a
problem with grip or trajectory. This is indicated by flashing of this
warning lamp in the instrument panel.
Deactivation
In exceptional conditions (starting a vehicle
w hich is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
these systems, so that the wheels can turn
freely and regain grip.
Reactivate these systems as soon as the level
of grip permits.
Deactivation of ASR and DSC using the button
F Press this button.
The orange indicator lamp in the button comes
on.
The ASR and DSC systems will no longer have
an effect on engine operation or the brakes in
the event of an involuntary change of trajectory.
Deactivation of ASR using the touch screen
The deactivation is configured in the
Driving/Vehicle menu.
It is confirmed by the display of a
message.
Reactivation
These systems are reactivated automatically
each time the ignition is switched back on or
above 31 mph (50 km/h).
Below 31
mph (50 km/h), you can reactivate
them manually.
5
Safety
Page 66 of 263
64
Advice
The driver must ensure that passengers
use the seat belts correctly and that they
are all fastened before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for
short journeys.
Do not interchange the seat belt buckles
as they will not fulfil their role fully.
The seat belts are fitted with an inertia
reel permitting automatic adjustment of
the length of the strap to your size. The
seat belt is stowed automatically when not
in use.
The inertia reels have an automatic
locking device at the time of a collision,
during sudden braking or if the vehicle
turns over. You can release the device by
pulling the strap firmly and then releasing
it so that it reels in slightly.
Before and after use, ensure that the seat
belt is reeled in correctly.
After folding or moving a
seat or rear
bench seat, ensure that the seat belt is
positioned and reeled in correctly. Installation
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in the
hollow of the shoulder.
In order to be effective, a seat belt must:
-
b
e tightened as close to the body as
possible,
-
b
e pulled in front of you with a smooth
movement, checking that it does not
twist,
-
b
e used to restrain only one person,
-
n
ot show any signs of cuts or fraying,
-
n
ot be converted or modified to avoid
affecting its performance.
Recommendations for children
Use a
suitable child seat if the passenger
is less than 12
years old or shorter than
one and a
half metres.
Never use the same seat belt to secure
more than one child.
Never allow a
child to travel on your lap.
For more information on Child seats , refer
to the corresponding section. Maintenance
In accordance with current safety
regulations, for all repairs on your
vehicle's seat belts, go to a
qualified
workshop with the skills and equipment
needed, which a
PEUGEOT dealer is able
to provide.
Have your seat belts checked regularly
by a
PEUGEOT dealer or a qualified
workshop, particularly if the straps show
signs of damage.
Clean the seat belt straps with soapy
water or a
textile cleaning product, sold by
PEUGEOT dealers.
In the event of an impact
Depending on the nature and
seriousness of the impact , the
pyrotechnic pretensioner may be deployed
before and independently of the airbags.
Deployment of the pretensioners is
accompanied by a
slight discharge of
harmless smoke and a
noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked and, if necessary,
replaced, by a
PEUGEOT dealer or
a
qualified workshop.
Safety
Page 87 of 263
85
F Move the gear lever to M.
F
P
ush the lever for ward to change
up.
F
P
ull the lever back to change
down.
Invalid value
This symbol is displayed if a gear
i s not engaged correctly (selector
between two positions).
You can change from position D to M and
from M to D at any time.
When the engine is running at idle with the
brakes released, if position R , D or M is
selected, the vehicle moves even without
the accelerator being pressed.
Never leave children unattended in the
vehicle when the engine is running.
When carrying out maintenance with the
engine running, apply the parking brake
and select position P . Never select position N while the vehicle
is moving.
Never select position P or R unless the
vehicle is completely stationary.
If position N is selected inadvertently while
driving, allow the engine to return to idle,
then select position D to accelerate.
If the temperature is below -23°C, the
engine should be left at idle for 4
minutes,
to ensure the correct operation and
service life of the engine and gearbox.
Sport and snow programmes
These two special programmes supplement the
automatic operation in very specific conditions
of use.
Sport programme " S"
F Press button " S" after starting the engine.
The gearbox automatically favours a dynamic
style of driving.
S appears in the instrument panel.
Snow programme T
(Depending on engine.)
F P ress the " T" button, after starting the
engine.
The gearbox adapts to driving on slippery
roads.
This programme improves starting and traction
when grip is poor.
T appears in the instrument panel.
At any time, press the selected button
again to quit the activated programme and
return to auto-adaptive mode.
Return to automatic
operation
F At any time, press button S or T again to quit the programme engaged and return to
auto-adaptive mode.
Stopping – Parking
Before switching off the engine.
F E ngage position P or N .
F
A
pply the parking brake.
F
Imm
obilise the vehicle.
6
Driving
Page 88 of 263
86
If the lever is not in position P, an alert
message appears on the screen on
opening the driver's door or approximately
45
seconds after switching off the ignition.
F
R
eposition the lever at position P ; the
message disappears.
When driving on flooded roads or when
crossing a
ford, proceed at walking pace.
When the ignition is on, the lighting
of this warning lamp, accompanied
by an audible signal and a
message
on the screen, indicates a
gearbox
fault.
In this case, the gearbox goes into back-up
mode by staying in 3rd gear. You may feel
a
substantial jolt when changing from P to
R and from N to R . This will not cause any
damage to the gearbox.
Do not exceed 62
mph (100 km/h), local speed
restrictions permitting.
Contact a
PEUGEOT dealer or a qualified
workshop as soon as possible. There is a
risk of damage to the gearbox:
F i f you press the accelerator and brake
pedals at the same time,
F
w
ith a flat battery, if you force the
movement of the lever from position P
to another position.
To reduce fuel consumption during
prolonged stops with the engine running
(e.g. traffic jam), position the gear lever at
N and apply the parking brake.
Gear shift indicator
(Depending on engine.)
System which reduces fuel consumption by
recommending the most appropriate gear.
Operation
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one or more gears. You can
follow this indication without engaging the
intermediate gears.
Gear shift recommendations must not be
considered as compulsory. In fact, the road
layout, the traffic density and safety remain the
deciding factors when choosing the best gear. With an automatic gearbox, the system is
only active in manual operation.
The information appears in the
instrument panel, in the form of an
ascending or descending arrow and
the recommended gear.
The system adapts its gear shift
recommendation according to the driving
conditions (slope, load, etc.) and the
driver's requirements (power, acceleration,
b r a k i n g , e t c .) .
The system never suggests:
-
e
ngaging first gear,
-
enga
ging reverse.
On vehicles fitted with a manual gearbox,
the arrow may be accompanied by the
gear recommended. The system always
recommends to change up if necessary.
Depending on the engine, it may also
recommend to change down if necessary.
The driver therefore remains responsible for
deciding whether or not to follow the indications
issued by the system.
This function cannot be deactivated.
Driving
Page 91 of 263
89
Deactivation/Reactivation
In certain circumstances, such as the need
to maintain the temperature in the passenger
compartment, it may be useful to deactivate the
Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
If the engine is in STOP mode, it then restarts.
The Stop & Start system is reactivated
automatically every time the ignition is switched
on.Opening the bonnet Driving on flooded roads
Before driving through a
flooded road, it is
strongly recommended that you deactivate
the Stop & Start system.
For more information on Driving advice ,
particularly on flooded roads, refer to the
corresponding section.
Malfunction
The Stop & Start system requires a 12 V
b attery of specific technology and
specification.
All work on this type of battery must be
carried out only by a
PEUGEOT dealer or
a
qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
F
T
o deactivate or reactivate the system,
press this button.
The indicator lamp is lit when the system is
deactivated.
Before doing anything under the bonnet,
deactivate the Stop & Start system to avoid
the risk of injury related to an automatic
change to START mode.
Under-inflation detection
This system automatically monitors the tyre
pressure while driving.
The system monitors the pressure in all four
tyres, once the vehicle is moving.
It compares the information given by the
wheel speed sensors with reference values,
which must be reinitialised after ever y tyre
pressure adjustment or wheel change .
The system triggers an alert as soon as it
detects a
drop in the pressure of one or more
tyres.
In the event of a
fault with the system, the ECO
OFF switch warning lamp flashes, then comes
on fixed.
Have it checked by a
PEUGEOT dealer or
a
qualified workshop.
If a
fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.
6
Driving