towing Peugeot 208 2019 Owner's Manual

3
.
bit.ly/helpPSA
.
Driving advice 80
Starting – Switching off the engine 8 1
Parking brake

8
2
Manual gearbox
8

3
Automatic gearbox (EAT6)

8
4
Gear shift indicator

8
6
Hill start assist

87
S

top & Start
87
U

nder-inflation detection
8
9
Speed limiter

9
1
Cruise control

9
3
Memorising speeds

9
5
Active City Brake

9
6
Parking sensors

9
8
Reversing camera
1

00
Park Assist

1
00Compatibility of fuels 1
06
Fuel tank 1 07
Misfuel prevention (Diesel)
1

08
Snow chains

1
08
Towing device

1
09
Load reduction mode

1
09
Energy economy mode
1

10
Fitting roof bars

1
10
B o n n e t


111
Engine


112
Checking levels

1
12
C h e c k s


114
AdBlue
® (BlueHDi engines) 1 17
Warning triangle
1
21
Running out of fuel (Diesel)

1
21
Temporary puncture repair kit
1

22
Spare wheel

1
25
Changing a
bulb
1
29
Changing a


fuse
1
33
12

V battery
1
37
To w i n g


14 0Engine technical data and towed loads

1
42
Engines and towed loads - PETROL
1
43
Engines and towed loads - DIESEL
1
45
Dimensions
1
47
Identification markings
1
48
Driving
Practical information
In the event of a breakdown Technical data
Alphabetical index
Access to additional videos
Audio equipment and telematics
Audio system
Bluetooth audio system
PEUGEOT Connect Radio
PEUGEOT Connect Nav
.
Contents

41
Returning the backrest to
the normal position
F Raise the seat backrest 2.
F L atch the backrest in place, the red indicator
in the control 1
is no longer visible.
F

U
nbuckle and reposition the seat belts
ready for use.
F

R
efit the head restraint(s).
When folding the seat, the centre seat belt
should not be fastened but laid out flat
along the seat.
When repositioning the seat backrest,
take care not to trap the seat belts.
The rear seat cushion does not fold, only
the seat backrest can be folded in order to
increase the boot loading space.
Head restraints
These have a position for use (up) and
a stowed position (down).
They can be removed and are interchangeable
side to side.
To remove a
head restraint:
F

p
ull the head restraint fully upwards,
F

t
hen, press lug A .
Never drive with the head restraints
removed; they must be fitted and correctly
adjusted.
Advice
Using the ventilation and air
conditioning system
F

T
o ensure that the air is distributed
evenly, keep the external air intake
grilles at the base of the windscreen,
the nozzles, the vents, the air outlets
and the air extractor in the boot free
from obstructions.
F

D
o not cover the sunshine sensor,
located on the dashboard; this is used
for regulation of the automatic air
conditioning system.
F

O
perate the air conditioning system for
at least 5
to 10 minutes, once or twice
a
month to keep it in per fect working
o r d e r.
F

I
f the system does not produce cold air,
switch it off and contact a
PEUGEOT
dealer or a
qualified workshop.
When towing the maximum load on
a
steep gradient in high temperatures,
switching off the air conditioning increases
the available engine power and so
improves the towing ability.
3
Ease of use and comfort

49
12 V accessory socket
F To connect a 12 V accessory (maximum
power: 120 watts), lift the cover and plug in
the correct adapter.
Do not exceed the maximum power rating
of the socket (risk of damage to your
accessory).
USB socket
The USB socket allows the connection of
a portable device, such as an iPod®-type digital
audio player, or a

USB memory stick.
The USB reader reads your audio files, which
are then transmitted to your audio system and
played via the vehicle's speakers.
These files are managed via the steering wheel
controls or from the audio system.
When connected to the USB socket,
the portable device can be charged
automatically.
While charging, a message is displayed
if the power consumption of the portable
device exceeds the amperage supplied by
the vehicle.
Boot fittings
1.Rear shelf
2. Hooks
3. Boot lamp
4. Stowing rings (depending on version)
The connection of an electrical device
not approved by PEUGEOT, such as
a

USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor radio
reception or inter ference with displays in
the screens.
For more detail on the Audio equipment and
telematics, and particularly the USB socket,
refer to the corresponding part of the audio
equipment section. The USB socket also allows a
smartphone to
be connected by MirrorLink
TM, Android Auto®
or CarPlay®, so that certain applications on the
smartphone can be used on the touch screen.
3
Ease of use and comfort

80
Driving advice
Observe driving regulations and remain vigilant
whatever the traffic conditions.
Pay close attention to the traffic and keep your
hands on the wheel so that you are ready to
react at any time to any eventuality.
As a safety measure, the driver should only
carry out any operations that require close
attention when the vehicle is stationary.
On a
long journey, taking a break every two
hours is strongly recommended.
In difficult weather, drive smoothly, anticipate
the need to brake and increase the distance
from other vehicles.
Never leave the engine running in
an enclosed area without adequate
ventilation: internal combustion engines
emit toxic exhaust gases, such as carbon
monoxide. There is a
risk of poisoning and
death!
In very severe wintry conditions
(temperatures below -23°C), to guarantee
correct operation and the longevity of
the mechanical elements of your vehicle,
engine and gearbox, the engine must be
left running for 4
minutes before driving.
Important!
Never drive with the parking brake applied
– Risk of overheating and damage to the
braking system!
As the exhaust system of your vehicle
is very hot, even several minutes after
switching off the engine, never park or run
the engine on inflammable sur faces (dry
grass, fallen leaves, etc.) – Risk of fire!
Never leave a vehicle unsuper vised with
the engine running. If you have to leave
your vehicle with the engine running, apply
the parking brake and put the gearbox into
neutral or position N or P , depending on
the type of gearbox.
Driving on flooded roads
We strongly advise against driving on flooded
roads, as this could cause serious damage
to the engine or gearbox, as well as to the
electrical systems of your vehicle.
In case of towing
Driving with a trailer places greater
d emands on the towing vehicle and
requires extra care from the driver.
If you are obliged to drive on a
flooded road:
-

c
heck that the depth of water does not
exceed 15 cm, taking account of waves that
might be generated by other users,
-

d
eactivate the Stop & Start function,
-

d
rive as slowly as possible without stalling.
In all cases, do not exceed 6 mph (10 km/h),
-

d
o not stop and do not switch off the engine.
On leaving the flooded road, as soon as safety
conditions allow, make several light brake
applications to dry the brake discs and pads.
If in doubt on the state of your vehicle, contact
a

PEUGEOT dealer or a qualified workshop.
Driving

81
Side wind
F Take into account the increased sensitivity to wind.
Cooling
Towing a trailer on a slope increases the
t emperature of the coolant.
As the fan is electrically controlled, its cooling
capacity is not dependent on the engine speed.
F

T
o lower the engine speed, reduce your
speed.
The maximum towable load on an incline
depends on the gradient and the exterior
temperature.
In all cases, keep a
check on the coolant
temperature.
F

I
f this warning lamp and the
STOP warning lamp come on,
stop the vehicle and switch off
the engine as soon as possible.
New vehicle
Do not tow a
trailer before having driven at
least 620
miles (1,000 kilometres).
Braking
Towing a trailer increases the braking distance.
T o avoid overheating of the brakes, the use of
engine braking is recommended.
Ty r e s
F Check the tyre pressures of the towing vehicle and of the trailer, observing the
recommended pressures.
Lighting
F Check the electrical lighting and signalling on the trailer and the headlamp beam height
of your vehicle.
For more information on Headlamp
beam height adjustment , refer to the
corresponding section.
Certain driving or manoeuvring aid
functions are automatically disabled if an
approved towing device is used.
Starting – Switching off
the engine
Ignition switch
1. Stop position.
2. Ignition on position.
3. Start position.
Avoid attaching heavy objects to the key
or the remote control, which would weigh
down on its blade in the ignition switch
and could cause a


malfunction.
Starting
With a manual gearbox, p lace the gear
selector in neutral then fully depress the clutch
pedal.
With an automatic gearbox , place the gear
selector at P or N then fully depress the brake
pedal.
6
Driving

97
allow the driver time to take back control of
the vehicle,
-

m
ay cause the engine to stall,
-

m
ay give rise to a pumping noise, due to the
pressurisation of the braking system.
The collision can be automatically avoided
if the speed difference between your
vehicle and the one ahead is not more
than 9
mph (15 km/h).
Above this threshold, the system will do
what is possible to avoid or reduce the
impact by lowering the speed of impact.
Activation/Deactivation
It is possible to activate or
deactivate the Active City Brake
from the Driving/Vehicle menu.
The system state remains memorised when the
ignition is switched off.
Each subsequent time the ignition is switched
on, if the automatic emergency braking function
is deactivated, a temporary message will
be displayed to point this out when a
speed
threshold (6
mph (10 km/h)) is exceeded. Deactivate the Active City Brake:
-

F
ollowing an impact to the windscreen
close to the sensor.
-
W
hen towing a trailer.
-
W
hen the vehicle is being towed.
-
W
hen the vehicle is about to cross
a toll barrier.
-
W
hen the vehicle is passing through
an automatic car wash.
Operating limits
Not detected are:
- Pe destrians, animals, motorcyclists,
cyclists.
-

F
ixed and non-reflective materials and
objects (cardboard box, wall, etc.).
-

V
ehicles not travelling in the same direction.
This system will not trigger or inter vene if the
driver:
-

p
resses the accelerator pedal firmly,
-

t
urns the wheel sharply (avoiding
manoeuvre).
Operating faults
Clean or clear any dirt, mist or objects (stickers,
leaves, etc.) from the top of the windscreen that
could obstruct the laser's field of vision. In the following cases, you should have the
system checked by a
PEUGEOT dealer or
a

qualified workshop:
-
T
he message "
Automatic braking system
fault " accompanied by an audible signal
indicates that a fault has been detected.
-
F
ollowing an impact, the system is
automatically put out of ser vice, it no longer
works. The system detects the deployment
of airbags.
Do not attempt to remove, adjust or test
the sensor.
Only a PEUGEOT dealer or a qualified
workshop is able to work on the system.
Misting of the windscreen or accumulations
of snow on the bonnet could inter fere with the
operation of the laser. A message appears if
the laser is obstructed.
Use windscreen demisting and regularly clean
the area of the windscreen in front of the
sensor.
Be particularly vigilant when driving in poor
weather (very heavy rain, hail, fog, snow, etc.).
This is because braking distances increase
while the laser's calculation parameters remain
the same.
6
Driving

99
Deactivation/activation of the
front and rear parking sensors
Without touch screen
F To deactivate or activate the system, press this button.
The indicator lamp is illuminated when the
system is deactivated.
The deactivation or activation of
the function is done in the Driving/
Vehicle menu.
The function will be deactivated
automatically if a
trailer is being towed
or a
bicycle carrier is fitted (vehicle fitted
with a
towing device or bicycle carrier
recommended by PEUGEOT).
Operating limits
- Certain obstacles located in the sensors' blind spots may not be detected or no
longer be detected during the manoeuvre.
-

S
ounds such as those emitted by noisy
vehicles and machinery (e.g. lorries,
pneumatic drills, etc.) may inter fere with the
vehicle's sensors.
-

C
ertain materials (fabrics) absorb sound
waves: pedestrians may not be detected.
-

A
ccumulated snow or dead leaves on the
road sur face can inter fere with the vehicle's
sensors.
-

A f
ront or rear impact to the vehicle can
distort the settings of the sensors, which is
not always detected by the system: distance
measurements may be incorrect.
-

T
he tilting of the vehicle if the boot is
very loaded can affect the distance
measurements.
-

T
he sensors may be affected by poor
weather conditions (heavy rain, thick fog,
snowfall, etc.).
Maintenance
recommendations
In bad or wintry weather, ensure that the
sensors are not covered with mud, ice or
snow. When reverse gear is engaged, an
audible signal (long beep) indicates that
the sensors may be dirty.
High-pressure jet wash
When washing your vehicle, keep the
lance at least 12
inches (30 cm) away from
the sensors.
Operating fault
If a fault occurs when shifting
t o reverse, this warning lamp
comes on in the instrument panel,
accompanied by a
message and an
audible signal (short beep).
Contact a
PEUGEOT dealer or a qualified
workshop to have the system checked.
With touch screen
6
Driving

103
The assisted exit from parking manoeuvre is in
progress.
Without exceeding 3 mph (5 km/h), continue
the manoeuvres following the information given
by the "Parking sensors" system, until the end
of manoeuvre message is displayed.
The manoeuvre is complete once the front
wheels of the vehicle are out of the parking
space.
The indicator lamp in the control goes off,
accompanied by an audible signal.
The driver takes back control of the vehicle's
steering.
Deactivation
The system is deactivated automatically:
- o n switching off the ignition,
-

i
f the engine stalls,
-

i
f no manoeuvre is per formed within
5
minutes of selecting the type of
manoeuvre,
-

a
fter a prolonged stop of the vehicle during
a


manoeuvre,
-

i
f the wheel anti-slip regulation (ASR) is
triggered,
-

i
f the speed of the vehicle exceeds the
stated limit,
-

w
hen the driver interrupts movement of the
steering wheel,
-

i
f the driver presses the Park Assist control,
-

i
f the vehicle cannot be properly positioned
(too many manoeuvres to get the vehicle in
or out),
-

i
f the driver's door is opened,
-

i
f one of the front wheels encounters an
obstacle.
A message is displayed in the screen. The driver then takes back control of the
vehicle's steering.
If the system is deactivated during
a


manoeuvre, the driver should reactivate
it manually to repeat the measurement.
Deactivation
The system is switched off automatically:
- w hen towing a trailer,
-

i
f the driver's door is opened,
-

i
f the speed of the vehicle is above 43 mph
(70


km/h).
To switch the system off for a
prolonged period,
contact a
PEUGEOT dealer or a qualified
workshop.
6
Driving

109
Installation tips
F If you have to fit the chains during a journey,
stop the vehicle on a flat sur face on the side
of the road.
F

A
pply the parking brake and position any
wheel chocks under the wheels to prevent
movement of your vehicle.
F

F
it the chains following the instructions
provided by the manufacturer.
F

M
ove off gently and drive for a few
moments, without exceeding 31
mph
(50


km/h).
F

S
top your vehicle and check that the snow
chains are correctly tightened.
It is strongly recommended that before
you leave, you practise fitting the snow
chains on a
level and dry sur face.
Avoid driving with snow chains on roads
that have been cleared of snow to avoid
damaging your vehicle's tyres and the
road sur face. If your vehicle is fitted with
alloy wheels, check that no part of the
chain or its fixings is in contact with the
wheel rim.
Towing device
Load distribution
F D istribute the load in the trailer so that the
heaviest items are as close as possible to
the axle and the nose weight approaches
the maximum permitted without exceeding
it.
Air density decreases with altitude, thus
reducing engine performance. The maximum
towed load must be reduced by 10% for every
1,000
metres of altitude.
Use towing devices and their genuine
harnesses approved by PEUGEOT. It
is recommended that the installation
be per formed by a
PEUGEOT dealer or
a


qualified workshop.
If the towing device is not fitted by
a
PEUGEOT dealer, it must still be
fitted in accordance with the vehicle
manufacturer's instructions.
Certain driving assistance or manoeuvring
assistance functions are automatically
disabled if an approved towing device is
used. Obser ve the maximum authorised towable
weight, indicated on your vehicle's
registration certificate, the manufacturer's
label as well as in the Technical data

section of this guide.
Complying with the maximum
authorised nose weight (towball)
also includes the use of accessories
(bicycle carriers, tow boxes, etc.).
Obser ve the legislation in force in the
country in which you are driving.
Load reduction mode
System which manages the use of certain
functions according to the level of charge
remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
certain functions, such as air conditioning,
heated rear screen, etc.
The deactivated functions are reactivated
automatically as soon as conditions permit.
7
Practical information

125
Do not drive more than 125 miles (200 km)
w ith the repaired tyre; see a PEUGEOT
dealer or a
qualified workshop to change
the tyre.
Under-inflation detection
Should the pressure of one or more tyres
be adjusted, it is necessary to reinitialise
the under-inflation detection system.
For more information on Under-inflation
detection , refer to the corresponding
section. After a
tyre repair, this warning
lamp will remain on until the
system is reinitialised.
For more information on Under-inflation
detection , refer to the corresponding
section.Spare wheel
Scan the QR code on page 3 to view
e xplanatory videos.
Procedure for changing a


damaged wheel with
the spare wheel using the tools provided with
the vehicle.
Access to the tools List of tools
1.
Wheelbrace.
For removing the wheel trim and removing
the wheel fixing bolts.
2. Jack with integrated handle.
Used to raise the vehicle.
3. Bolt "cover" tool.
For removing the bolt protectors (covers)
on alloy wheels.
4. Socket for the security bolts.
For adapting the wheelbrace to the special
"security" bolts.
5. Towing eye.
For more information on To w i n g , refer to
the corresponding section.
The tools are installed in the boot under the
f l o o r.
To gain access:
F

o

pen the boot,
F

l

ift the floor and remove it,
F

r

emove the carrier box containing the tools.
8
In the event of a breakdown