ignition Peugeot 301 2018 Service Manual

105
Procedure
Before topping up, ensure that the vehicle is
parked on a flat and level sur face.
In wintry conditions, ensure that the
temperature of the vehicle is above -11°C.
Otherwise the AdBlue
® may be frozen and
so cannot be poured into its tank. Park your
vehicle in a warmer area for a few hours to
allow the top-up to be carried out.
F

S

witch off the ignition and remove the key.
F

Un

clip the plastic plug. F

C
arefully lift off the cap, without dropping it.
F

F

or access to the AdBlue
® tank, open the
boot, remove the boot floor and then lift out
the storage box containing the tools.
F

I

nsert your fingers into the aperture and turn
the blue cap 1/6 of a turn anti-clockwise. F

G
et a bottle or container of AdBlue
®. After
first checking the use-by date, carefully
read the instructions on use on the label
before pouring the contents of the bottle into
your vehicle's AdBlue
® tank.
Important: if your vehicle's AdBlue
® tank is
c
ompletely empty – which is confirmed by
the alert displays and the impossibility of
starting the engine – you must add at least
3.8

litres (so two 1.89

litre bottles).
F

A

fter emptying the bottle or container, wipe
away any spillage around the tank filler
using a damp cloth. If any additive is spilt or splashed, wash
immediately with cold water or wipe with a
damp cloth.
If the additive has crystallised, clean it off
using a sponge and hot water.
F
R
efit the blue cap to the tank and turn it 1/6
of a turn clockwise, to its stop.
F
R
eplace the plastic plug, clipping it in the
opening.
F
R
eturn the storage box containing the tools
to its location.
F
R
eplace the boot floor and close the boot.
Never dispose of AdBlue
® additive
bottles or containers in the household
waste. Place them in a container
provided for this purpose or take them
to your dealer.
Important: if topping up after running
out of AdBlue , you must wait for
approximately 5 minutes before switching
the ignition back on, without opening
the driver's door, unlocking the vehicle
or inser ting the key into the ignition
switch . Switch on the ignition, then, after
10 seconds, start the engine.
7
Practical information

108
Changing a wiper blade
Before removing a front
wiper
F Within one minute after switching off the ignition, operate the wiper control stalk to
position the wiper blades in the middle of
the windscreen (maintenance position).
Removing
F Lift the corresponding wiper arm away from the windscreen.
F

U
nclip and remove the wiper blade.
Refitting
F Position and clip the new wiper blade to the arm.
F

C
arefully lower the wiper arm.
After refitting a front wiper
F Switch on the ignition.
F O perate the wiper control stalk again to
park the wiper blades.
Towing a trailer
Your vehicle is primarily designed for
transporting people and luggage, but it may
also be used for towing a trailer.
We recommend the use of genuine
PEUGEOT towbars and their harnesses
that have been tested and approved from
the design stage of your vehicle, and that
the fitting of the towbar is entrusted to a
PEUGEOT dealer or a qualified workshop.
If the towbar is not fitted by a PEUGEOT
dealer, it must still be fitted in accordance
with the vehicle manufacturer's
instructions.
Practical information

113
Engines
Petrol
Diesel
These engines are examples provided as a
guide.
The locations of the following elements may
vary:
-
E
ngine oil dipstick.
-

E
ngine oil filler cap.
-
P

riming pump. 6.
A i r f i l t e r.
7. Engine oil dipstick.
8. Engine oil filler cap.
9. Priming pump*.
To avoid damaging the electrical units,
never use a high-pressure jet wash in the
engine compartment.
The Diesel circuit is under very high
pressure.
All work on this circuit must be carried out
only by a PEUGEOT dealer or a qualified
workshop.
*
D
epending on engine.
1.
Screenwash fluid reservoir.
2. Engine coolant reservoir.
3. Brake fluid reser voir.
4. Battery.
5. Fusebox.
Checking levels
Check all of these levels regularly, in line with
the manufacturer's service schedule. Top them
up if necessary, unless other wise indicated.
If a level drops significantly, have the
corresponding system checked by a PEUGEOT
dealer or a qualified workshop.
The fluids must comply with the
manufacturer's recommendations and with
the vehicle's engine.
Take care when working under the bonnet,
as certain areas of the engine may be
extremely hot (risk of burns) and the
cooling fan could start at any time (even
with the ignition off).
Used products
Avoid prolonged contact of used oil or
fluids with the skin.
Most of these fluids are harmful to health
or indeed very corrosive.
7
Practical information

118
Running out of fuel
(Diesel)
On vehicles fitted with HDi engines, the fuel
system must be primed if you run out of fuel.
For more information about the Engines, in
particular the location of the different parts
under the bonnet, refer to the corresponding
section.
For more information on Diesel misfuel
prevention , refer to the corresponding section.
If the engine does not start the first time,
do not keep trying, but start the procedure
again from the beginning.
HDi 92 engine
F If the engine does not start after a few attempts, operate the priming pump again
then start the engine.
F

C
lose the bonnet again.
BlueHDi engines
F Fill the fuel tank with at least five litres of Diesel.
F

S
witch on the ignition (without starting the
engine).
F

W
ait around 6 seconds and switch off the
ignition.
F

R
epeat the operation 10 times.
F

O
perate the starter to run the engine.
Temporary puncture
repair kit
Comprising a compressor and a sealant
cartridge, it allows the temporary repair of
a tyre so that you can drive to the nearest
garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Access to the kit
F Fill the fuel tank with at least five litres of Diesel.
F

O
pen the bonnet.
F

O
perate the priming pump repeatedly until
resistance is felt (there may be resistance at
the first press).
F

O
perate the starter until the engine starts (if
the engine does not start at the first attempt,
wait around 15
seconds before trying
again). This kit is installed in the storage box, under
the boot floor.
In the event of a breakdown

119
The vehicle's electric system allows the
connection of the compressor for long
enough to inflate a tyre after a puncture
repair.
Composition of the kit
1.12 V compressor, with built-in pressure
gauge.
2. Bottle of sealant, with built-in hose.
3. Speed limit sticker.
The speed limit sticker must be secured
to the interior of the vehicle in the driver's
field of vision, to remind you that a wheel
is in temporary use. Do not exceed a speed of 50
mph
(80
k
m/h) when driving with a tyre repaired
using this type of kit.
Repair procedure
F Switch off the ignition.
F S ecure the speed limit sticker inside the
vehicle.
F

U
ncoil the pipe stowed under the
compressor.
Avoid removing any foreign bodies which
have penetrated into the tyre.
F

C
onnect the pipe from the compressor to
the bottle of sealant. F

R
emove the valve cap from the tyre to be
repaired, and place it in a clean area.
F

T
urn the sealant bottle over and secure it in
the cut-out provided on the compressor.
F

C
onnect the hose from the bottle of sealant
to the valve of the tyre to be repaired and
tighten firmly.
8
In the event of a breakdown

120
F Check that the compressor switch is at the position " O".
F

F
ully uncoil the electric cable, stowed under
the compressor.
If after around five to seven minutes the
pressure of 2
bars is not attained, this
indicates that the tyre is not repairable;
contact a PEUGEOT dealer or a qualified
workshop for assistance.
F Place the switch in the " O" position.
F R emove the kit.
Take care, the sealant product is harmful
if swallowed and causes irritation to the
eyes.
Keep this product out of the reach of
children.
The use-by date is marked on the bottle.
After use, do not discard the bottle by the
roadside, take it to a PEUGEOT
dealer or
an authorised waste disposal site.
Do not forget to obtain a new bottle of
sealant, available from a PEUGEOT
dealer or a qualified workshop.
Checking/adjusting tyre
pressures
You can also use the compressor,
without injecting sealant, to check and, if
necessary, adjust the tyre pressures
F

R
emove the valve cap from the tyre and
place it in a clean area.
F

C

onnect the compressor's electrical
connector to the vehicle's 12

V socket.
F

S

witch on the ignition. F

S

witch on the compressor by moving the
switch to the position " I" until the tyre
pressure reaches 2.0

bars. The sealant is
injected under pressure into the tyre; do not
disconnect the hose from the valve during
this operation (risk of splashing).
F Stop to check the repair and the tyre pressure using the kit.
F

D

rive immediately for approximately three miles
(five kilometres), at reduced speed (between 12 and
37

mph (20 and 60

km/h)), to plug the puncture.
In the event of a breakdown

121
F Check that the compressor switch is at the position " O".
F

F
ully uncoil the electric cable, stowed under
the compressor.
F

U
ncoil the pipe stowed under the
compressor.
F
S
crew the pipe onto the valve and tighten
f i r m l y.
F
C
onnect the compressor's electric plug to
the vehicle's 12
V socket. F

S
witch on the ignition.
F
S
witch on the compressor by moving the
switch to the position " I" and adjust the
pressure as shown on the vehicle tyre
pressure label. To deflate: press the black
button on the compressor hose by the valve
connector.
F

O
nce the correct pressure is reached, put
the switch to the position " O".
F

R
emove the kit then stow it.Tyre under-inflation detection
Should the pressure of one or more tyres
be adjusted, it is necessary to reinitialise
the under-inflation detection system.
For more information on Under-inflation
detection
, refer to the corresponding
section. After a tyre repair, the warning
lamp will remain on until the
system is reinitialised.
For more information on Tyre under-
inflation detection , refer to the
corresponding section.
8
In the event of a breakdown

124
Removing a wheel
Parking the vehicle
* position P for the automatic gearbox
Park the vehicle where it does not block
traffic: the ground must be level, stable
and non-slippery.
Apply the parking brake, switch off the
ignition and engage first gear* so as to
block the wheels.
Check that the parking brake warning
lamp comes on fixed in the instrument
panel.
The occupants must get out of the vehicle
and wait where they are safe.
Make sure that the jack is correctly
positioned at one of the vehicle's jacking
points.
Incorrect use of the jack could cause the
vehicle to collapse.
Never go underneath a vehicle raised
using a jack; use an axle stand.
Do not use a jack other than the one
supplied by the manufacturer.
Wheel with hub cap
When removing the wheel
, first remove
the hub cap using the wheelbrace by
pulling at the valve aperture.
When refitting the wheel , after tightening
the wheel bolts, refit the hub cap, starting
by placing its aperture in line with the
valve and then pushing it into place all
round its edge with the palm of your hand.
List of operations
F Remove each wheel bolt cover using the tool 3 (alloy wheels).
F

L
oosen the bolts using wheelbrace 1 o n l y. F

P
lace the foot of jack 2 on the ground and
ensure that it is directly below the front
A or rear B jacking point provided on the
underbody, whichever is closest to the
wheel to be changed.
In the event of a breakdown

126
List of operations
Changing a bulb
The headlamps have polycarbonate
lenses with a protective coating:
F
d
o not clean them using a dr y or
abrasive cloth, nor with a detergent
or solvent product,
F

u
se a sponge and soapy water or a pH
neutral product,
F

w
hen using a high pressure washer
on persistent marks, do not keep the
lance directed towards the lamps or
their edges for too long, so as not to
damage their protective coating and
seals.
Changing a bulb must only be done with
the ignition off and after the headlamp has
been switched off for several minutes –
Risk of serious burns!
F

D
o not touch the bulb directly with your
fingers, use a lint-free cloth.
It is essential only to use anti-ultraviolet
(UV) type bulbs, so as not to damage the
headlamp.
Always replace a failed bulb with a new
bulb with the same type and specification.
Fastening the spare wheel
If your vehicle is fitted with alloy wheels,
when tightening the bolts on fitting, it is
normal to notice that the washers do not
come into contact with the spare wheel.
The wheel is secured by the conical
contact of each bolt.
After changing a wheel
Do not exceed 50 mph (80 km/h) when
using a "space-saver" type spare wheel.
Have the tightening of the bolts and the
pressure of the spare wheel checked by a
PEUGEOT dealer or a qualified workshop
without delay.
Have the punctured wheel repaired and
reinstall it on the vehicle as soon as
possible.
Fitting a wheelF Put the wheel in place on the hub.
F
Screw in the bolts by hand as far as possible.F Pre-tighten the bolts using wheelbrace 1 o n l y.
F

L
ower the vehicle again fully.
F

F
old jack 2 and detach it.
F

T
ighten the bolts using wheelbrace 1 o n l y.
F

R
efit the wheel bolt covers (alloy wheels).
F

S
tow the tools in their box.
In the event of a breakdown

131
To refit, carry out these operations in reverse
o r d e r.Check that the housing cover is positioned
correctly on its support before clipping it
on.
Licence plate lamps
(W5W)
F Insert a thin screwdriver into one of the exterior holes of the transparent lens.
F

P
ush it outwards to unclip it and remove it.
F

R
emove the defective bulb and replace it.
For reassembly, carry out these operations in
reverse order.
Changing a fuse
Access to the tooling Changing a fuseBefore changing a fuse:
F
T he cause of the failure must be identified
and rectified.
F

A
ll devices consuming electricity must be
switched off.
F

T
he vehicle must be immobilised with the
ignition off.
F

I
dentify the defective fuse using the
allocation tables and diagrams.
To remove or fit a fuse, it is essential to:
F

U
se the special pliers to extract the fuse
from its housing and check the condition of
its filament.
F

A
lways replace the failed fuse with a fuse
of the same rating (same colour); using a
different rating could cause faults (risk of
f i r e).
If the fuse fails again soon after
replacement, have the vehicle's electrical
system checked by a PEUGEOT dealer or
a qualified workshop.
The replacement of a fuse not shown in
the allocation tables below may cause
a serious malfunction of your vehicle.
Contact a PEUGEOT dealer or a qualified
workshop.
The extraction tweezers are fitted to the back
of the dashboard fusebox cover.
F

U

nclip the cover by pulling at the top right,
then left.
F

D

isengage the cover fully and turn it over.
F

P

ull out the pliers.
8
In the event of a breakdown