mileage Peugeot 301 2018 Owner's Manual

20
Warning/indicator lampStateCause Action/Observations
Service spanner Flashing then fixed,
when the ignition is
switched on. Service is overdue.
The ser vice indicator is displayed for a few seconds
in the instrument panel. Depending on the version:
-

t
he total distance recorder displays a line showing
the distance travelled since ser vice was due. The
value is preceded by the "-" sign.
-

a
n alert message indicates that ser vice is
overdue.
The ser vice spanner remains on until the ser vice has
been performed.
The alert is triggered when the due date has passed.
+ Flashing then fixed,
when the ignition
is switched on,
associated with the
Ser vice warning
lamp.Ser vice is overdue for Diesel
BlueHDi versions.
The ser vice indicator is displayed for a few seconds
in the instrument panel. Depending on the version:
-

t
he total distance recorder displays a line showing
the distance travelled since ser vice was due. The
value is preceded by the "-" sign.
-

a
n alert message indicates that ser vice is
overdue.
The ser vice spanner remains on until the ser vice has
been performed.
The alert is triggered when the due date has passed.
The distance indicated (in kilometres
or miles) is calculated according to the
mileage covered and the time elapsed
since the last ser vice.
Instruments

94
Programming
You do not have to switch the speed limiter on
in order to set the speed.
F
T
urn thumb wheel 1 to the "LIMIT" position:
the speed limiter mode is selected but is not
switched on (PAUSE).
F

S
et the speed value by pressing button 2 or
3 (e.g. 56 mph (90 km/h)).
You can change the programmed speed further
using buttons 2 and 3 :
-

B
y +/- 1 mph (1 km/h) = short press.
-

B
y +/- 5 mph (5 km/h) = long press.
-

In steps of +/- 5 mph (5 km/h) = press and hold.F Switch the speed limiter on by pressing button 4 .
Pause
F Switch the speed limiter off by pressing
button 4: a message on the screen confirms
the stop (PAUSE).
F

S
witch the speed limiter back on by
pressing button 4 again.
Temporarily exceeding the
speed setting
Pressing the accelerator pedal in order to
exceed the programmed speed will have no
effect unless you press the pedal firmly beyond
the point of resistance .
The speed limiter is deactivated temporarily and
the programmed speed, which is still displayed,
flashes, accompanied by an audible signal. Returning to the programmed speed, by means
of intentional or unintentional deceleration of the
vehicle, automatically cancels the flashing of the
programmed speed and the audible signal stops.
Exiting limiter mode
F Turn thumb wheel 1 to the 0 position: the
speed limiter mode is deselected. The
display returns to the total mileage recorder.
Operating fault
In the event of a speed limiter fault, the speed
is cleared resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Driving

96
5Cruise control off/resume indication.
6 Cruise control selection indication.
7 Programmed speed value.
Programming
F Turn thumb wheel 1 to the "CRUISE"
position: the cruise control mode is selected
but is not switched on (PAUSE).
F

S
et the programmed speed by
accelerating to the required
speed, then press button 2 or 3
(e.g. 65 mph (110 km/h)).
Pause
F Switch off the cruise control by pressing button 4: a confirmation message appears
on the screen (PAUSE).
You can change the programmed speed further
using buttons 2 and 3
:
-
B
y +/- 1 mph (1 km/h) = short press.
-
B
y +/- 5 mph (5 km/h) = long press.
-
I
n steps of +/- 5 mph (5 km/h) = press and
hold. F
S
witch the cruise control back on by
pressing button 4 again.
Exceeding programmed
speed
Intentional or unintentional exceeding of the
programmed speed results in flashing of this
speed on the display.
Returning to the programmed speed, by means
of intentional or unintentional deceleration of
the vehicle, automatically cancels the flashing
of the programmed speed.
Exiting cruise control mode
F Turn thumb wheel 1 to the 0 position: the cruise control mode is deselected. The
display returns to the total mileage recorder.
Displays on the instrument panel
The programmed information is grouped
together in the instrument panel screen.
Driving