ECU Peugeot 306 Break Dag 2002 Owner's Manual

1
4
3
A
2
YOUR 306 AT A GLANCE11
FOLDING REAR SEAT BACK
To fold the seat back:
- from inside the boot, release control 1
- position the seat belt under the strap guide B
- unlock the seat back by press- ing button A
- tilt the seat back
- tilt the backrest. When repositioning the seat back, ensure thatthe seat belts are posi-tioned correctly and theseat back is secured cor-rectly .
FOLDING REAR SEATS (all models)
To fold the rear seats:
- insert the seat belt stalks in the hooks A.
- pull the strap 1.
- tilt the seat cushion 2against the front seats.
- position the seat belt under the lever 3(5-door and estate) or on the top
of the seat back (3-door).
- unlock the seat back using the controls on the side 3(5-door and estate)
or on the seat back 4 (3-door).
- tilt the seat back 4.
To tilt the rear seats, always start with the seat cushion, never with the backrest (risk of damage). When repositioning, take care to avoid trapping the seat belts under the seat cushion or behind the seat back.
BA
1
8586

YOUR 306 AT A GLANCE9
FUEL FILLER FLAP
To open*: firmly pull the handle on the floor to the outside of the drivers seat.
To close: from outside, push the flap back and check that it is secured
correctly. The fuel filler cap is opened and closed with the ignition key independently of opening the doors (during model year). Filling with fuel Switch off the engine.There is a holder for the fuel filler cap.
A label on the inside of the flap shows which fuels are permitted and which are not allowed. The capacity of the tank is approximately 13 gallons (60 litres).
Fuel low warning light The fuel low warning light indicates that the quantity of fuel remaining in the tank is approximately 1.3 gallons (6 litres). * According to specification.
Outside the vehicle Raise the catch 1and
support the bonnet as it rises.
OPENING THE BONNET Inside the vehicle:
Pull the
handle.
8182

1
1
3
5
2
A4
85
YOUR 306 IN DETAIL
REAR SEATS (3 and 5 doors)
To fold the rear seats:
- insert the seat belt stalks in the hooks A.
- pull the strap 1.
- tilt the seat cushion 2against the front seats.
- position the seat belt under the lever 3(5-door) or under the strap guide
(3-door).
- unlock the seat back using the controls on the side 3(5-door) or on the seat
back 4(3-door).
- tilt the seat back 5.
To tilt the rear seats, always start with the seat cushion, never with the seat back (risk of damage). When repositioning, take care to avoid trapping the seat belts under the seat cushion or behind the seat back.
To remove the rear seat cushion, tilt the seat cushion through 90¡ and remove it.
To replace the seat cushion: position it on the front securing plates and lower it into its normal position. Rear parcel shelf Rear parcel shelf with integral speakers
To remove:
- Turn the speaker connector to the
left then disconnect it.
- Unhook the two cords.
- Raise the shelf.
- Remove the shelf.Storage: turn the shelf over and lay it flat in the boot. Rear parcel shelf without integral speakers
To remove:
- Unhook the two cords.
- Raise the shelf.
- Remove the shelf.

86The additional locking control 1locks
the seat back. Access is from inside the boot: 0 : Locking
0 : Unlocking
It is essential to lock the seat back to prevent access to the boot frominside the vehicle.
X
From inside the boot, unlock the control
1.
Position the seat belt under the strapguide B.
Unlock the seat back by pressing thebutton A.
Tilt the seat back. When repositioning, ensure that the seat belts are positioned correctly andthat the seat back is secured
correctly.
* According to specification.
To fold the seat back Insert the seat belt stalks in the hooks. The seat back can be folded in one or two parts*.
YOUR 306 IN DETAIL
REAR SEATS (4 door)
AB
1

1
4
3
A
2
87
To fold the rear seats: - Insert the seat belt stalks in the hooks A.
- Pull the strap 1.
- Tilt the seat cushion 2against the front seats.
- Position the seat belt under the lever 3.
- Unlock the seat back using the controls on the side 3.
- Tilt the seat back 4.
To tilt the rear seats, always start with the seat cushion, never with the seat back (risk of damage). When repositioning, take care to avoid trapping the seat belts under the seat cushion or behind the seat back.
To remove the rear seat cushion, tilt the seat cushion through 90 degrees and remove it.
To replace the seat cushion: position it on the front securing plates and lower it into its normal position. Luggage cover Access to the boot: -
from the rear: fold the components
like an accordion.
- from the front (from the rear seats): raise the part behind the
seat back.
Retaining nets* The lashing points permit the use of a
luggage retaining net. A full heightload net is also available as an acces-
sory.
* According to specification.
YOUR 306 IN DETAIL
REAR SEATS (estate)

123
CHILD SEATS All children under the age of 10 are required to travel in approved child safety seats*, fitted with seat belts.
After carrying out numerous tests, PEUGEOT recommend the following systems :Up to 9 months (up to 22 lbs. or 10 kg) ÇBaby SafeÈ, a seat secured with its back to the engine and secured with a three-point seat belt, on either the front or rear seat.
From 9 months to 3 or 4 years (20 to 40 lbs. or 9 to 18 kg)
ÇRšmer PeggyÈ is fitted to the rear seat with a two-point (lap-belt) or three-pointbelt.
From 3 to10 years of age (33 to 80 lbs or 15 to 36 kg) ÒKlippan OptimaÓ : is fitted in the rear with a three point belt (removable seatback). from 33 to 55 lbs. [15 to 25 kg] : booster + seatback.from 55 to 80 lbs. [25 to 36 kg] : use the booster on its own.
For maximum safety, fasten the three-point seat belts or the child seat straps keeping
the slack in relation to the childÕs body to a minimum, even for short journeys.
To prevent the doors from opening accidentally: use the child-proof lock.Also, do not open the rear windows more than a third.
88
YOUR 306 IN DETAIL
Never leave a child in a vehicle which is exposedto the sun and has thewindows closed.
To protect young children
from the sun, fit sunblinds to the rear windows. Never leave the keys in the reach
of children inside the car. Strap children into their child seats even on short journeys. Observe the precautions concern- ing the passenger airbag.
This was one of PEUGEOTÕs main criteria when designing your vehicle, however the safety of your children also depends on you. For maximum peace of mind,please follow these simple precautions: *According to current legislation
1
2
3

YOUR 306 IN DETAIL
82
Fuel filler flap
To open*:
firmly pull the handle on the
floor to the outside of the driverÕs seat.
To close: from outside, push the flap
back and check that it is secured
correctly.
* According to specification. Filling with fuel Switch off the engine. There is a holder for the fuel filler cap.
A label on the inside of the flap shows which fuels are permitted and whichare not allowed. The capacity of the tank is approx- imately 13 gallons (60 litres). Use the ignition key to open and close the fuel filler cap independently ofopening the doors.

1
3
1
2
2
12
MAINTENANCE OF YOUR 306
32
Access to the spare wheel The wheel is on the outside of the vehicle, under the boot, supported by a metal
carrier.
Take out the wheelbrace
1.
Using the wheelbrace 1, unscrew the spare wheel carrier securing bolt located
under the carpet in the boot.
Raise the carrier to release the hook rearwards, then lower the carrier.Release the spare wheel.
Jack location Petrol and Diesel 3 or 5 door:
the jack is in the boot 2.
Rear crossbar (right side). Press the tab and open the storage box toremove it. 4 door: the jack is in the left-hand side
of the boot.Estate: the jack is in the right-hand
storage compartment of the boot.CHANGING A WHEEL

MAINTENANCE OF YOUR 30633
For your safety, always change the wheel:
- on level, stabIe and non-slippe- ry ground,
- with the handbrake applied,
- with first gear or reverse enga- ged (position Pfor the automa-
tic gearbox).
Never go underneath a vehicle which is supported only by a jack.(Use a ramp).
To fit the wheel After positioning the wheel, pre- tighten the bolts using the wheel-brace. Lower the jack and remove it.Fully tighten the wheel bolts using the wheelbrace. Fit the wheel trim starting with the section by the valve and press intoplace using the palm of the hand.
Removing the wheel Park the vehicle on level, stable and non-slippery ground. Apply the handbrake, engage first gear or reverse (position Pfor the
automatic gearbox). Remove the wheel trim by using the wheelbrace and pulling next to thevalve.
Warning: your wheel trims are fitted
with dummy nuts. Do not use them to remove your wheel trims. 4-door:
Use the jack storage box to
chock the wheel diagonally oppositethe wheel to be changed. Loosen the wheel bolts.Place the jack in the location designed for it, as close as possible to the wheelto be changed. Ensure that the whole of the base of the jack is in contact with the ground. Extend the jack, fully loosen the wheel bolts and remove the wheel. Refitting the wheel in the carrier
Raise the wheel, then the carrier, and resecure it on the hook. Do not forget to fully tighten the spare wheel carrier securing bolt. After changing the wheel:
- have the tightening of the bolts
and the tyre pressure checked by a PEUGEOT dealer as soonas possible,
- have the punctured wheel repaired and refit it to thevehicle as soon as possible.

33
MAINTENANCE OF YOUR 306
34
Special features of the alloy wheels* Bolt covers Alloy wheel bolts are covered by chrome trims. Use tool
3to remove the trims befo-
re slackening the bolts. Anti-theft bolts** If your wheels are fitted with an anti- theft bolt (one per wheel), the chro-me trim and then the plastic covermust be removed using tool
3, befo-
re unscrewing the bolt using one ofthe two anti-theft sockets (whichwere given to you on delivery of yourvehicle with the duplicate keys andthe confidential card) and the wheelbrace 1.
Comment: make a careful note of
the code number engraved on the
head of the anti-theft socket. Thiswill enable you to obtain a duplicateof the anti-theft sockets from a
Peugeot dealer.
* According to specification.
** According to model and destina- tion.
Fitting the spare wheel If your vehicle is fitted with a steel spare wheel, it is
normalto notice
that the bolt washers do not come
into contact with the rim. The sparewheel is secured by the cone shape
of each bolt. Tighten the bolts fully. Fitting snow tyres If you fit snow tyres mounted on steel wheels, it is essentialto use special
bolts available from your PEUGEOT
dealer.