window Peugeot 306 C 2001 Owner's Manual

YOUR 306 CABRIOLET AT A GLANCE3
1
- Side window demisting vents.
2 - Adjustable side vent.
3 - Passenger airbag.
4 - Windscreen demisting vents.
5 - Controls:
Lighter Hazard warning lightsRear screen and mirrors demisting.
6 - Heating/Ventilation,
Air conditioning controls*.
7 - Audio equipment*.
8 - Adjustable central vents. 9
- Lights stalk, fog lamps* and
horn.
10 - Steering wheel with airbag.
11 - Audio remote control*.
12 - Windscreen wash-wipe control.
13 - Headlamp height
adjustment.
- Instrument dials lighting rheostat.
14 - Controls for:
- Electric mirrors.
- Electric windows.
15 - Control for rear window lock.
16 - Bonnet opening control. 17
- Passenger airbag
disarming switch*.
18 - Fuse box.
19 - Steering lock and ignition.
20 - Handbrake.
21 - Gear lever.
22 - Storage compartment.
23 - Ashtray.
24 - Glove box.
* According to specification.

ELECTRIC WINDOWS
1. Driver's electric window
Manual mode: press or pull the switch lightly. The window stops as soon as the switch is released.
Automatic mode: press or pull the switch firmly. One touch completely opens
or closes the window. Automatic opening and closing only work when the engine is running.
2. PassengerÕs electric window.
3. Left rear electric window.
4. Right rear electric window.
YOUR 306 CABRIOLET AT A GLANCE
8
ADJUSTING THE HEIGHT OF THE STEERING WHEEL Push the handle to unlock the steering wheel. Adjust the steering wheel to the desired height and pull the handleto lock it into position.
96
ELECTRIC MIRRORS
Turn the knob
Ato the right or to the left to select the
corresponding mirror.
Move the knob in all four directions to adjust the mirror.
34
94
2
A
1

YOUR 306 CABRIOLET AT A GLANCE11
46
ELECTRIC HOOD Opening
- Switch on the ignition.
- Unlock and raise the front of
the hood by approximately 10 inches (25 cm) using thetwo side handles 1.
- Press switch 2until the opera-
tion has been completed.
Closing
- Turn the ignition key to position M and lower the front windows.
- Press switch 2until the opera-
tion has been completed.
- Secure the two side handles 1.
1
12

YOUR 306 CABRIOLET AT A GLANCE
12
5 - Recirculation of interior air.
VENTILATION/HEATING/AIR CONDITIONING
1 - Air flow adjustment.
2 - Temperature adjustment.
3 - Air distribution.
Windscreen and side windows. Windscreen, side windows and footwells. Footwells. Central and side vents.
4 - Air conditioning on/off.
56
123
123
45

ELECTRIC HOOD: CLOSING Inside the vehicle:
- Turn the ignition key to position M
(engine not running, oil pressure warning light on) and lower thefront windows.
- Press the switch 4on the central
console until the operation hasbeen completed (hood unfoldeduntil it stops not quite flush withthe windscreen). Using the centre handle and a sidehandle, fold down the front of thehood, position the side handle hooksin their housings and secure the twohandles. As a safety precaution,opening and closingoperations must be car-
ried out when stationary.Driving with the hood
cover open is prohibited.
If the boot is not closed, the hood
cannot be opened or closed.
If the front of the hood is not
closed, the hood cannot be
opened.
Do not carry out too many opera-
tions in succession as there is a
risk that the battery may become
flat.
Do not place anything in the com-
partment reserved for storing the
hood as there is a risk of damage.
Before opening the hood:
- Ensure that the hood and rear screen are clean.
- Ensure that the hood is dry, otherwise the compression it is
subjected to when it is folded
will result in marks or even
stains caused by moisture over
time.
YOUR 306 CABRIOLET IN DETAIL 47
4

HARD-TOP : REMOVAL
Tools
Your Hard-top is supplied with a tool kit containing: 1- A storage case.
2 - Two retaining straps.
3 - A screwdriver with two heads.
4 - A pair of gloves.
5 - A special spanner.
6 - A 17mm flat spanner. Apply the handbrake.Switch on the ignition.Open all the windows.
Switch off the ignition.
- Unscrew the covers
11on the quar-
ter panels. - Hold the side flaps
7in the open
position using one of the straps 2.
- Disconnect the heated rear screen harness connector 8.
- Release the rear fasteners 9using
the special spanner 5(a quarter
turn from the front to the rear of the vehicle.
WARNING The removal-refitting operations described below should have beendemonstrated by your PEUGEOTdealer on handover of your vehicle. If your Hard-top was supplied as
an accessory, the first removaloperation must be carried out by
an approved dealer. The opera-tion must be carried out by threepeople.
YOUR 306 CABRIOLET IN DETAIL
50
6
3
5 1 4
2
11
98
7
2
5
9
12
14

- Release the two front side handles13 .
- Remove the hard top and careful- ly place it on a clean and stable stand. - From the boot, manually open the
hood cover 10. To do this, remove
the cap and turn the control aquarter turn clockwise using thewheelbrace. Remove the wheel-brace, close the boot and hold thehood cover 10open using the sec-
ond strap 2.
- Remove the two side brackets 12
using the 17 mm flat spanner 6.
- Connect connector 8to the har-
ness connector located behind theside flap 14on the right hand side
of the rear shelf (if the connectionis not made, the hood and blowerwill not operate).
- Remove the retaining straps 2
from the hood cover 10and from
the side flaps 7.
- Close the hood cover 10manually.
- Switch on the ignition.
- Close the hood and the windows. Before folding the hood into its housing, ensurethat it has been brushedand dried to remove any
moisture and that the rear screen
is folded correctly.
To prevent damage to the hood cover and the boot, the boot mustbe closed during the hood coverlowering and raising operations. Although the hood cover may appear to support itself in the ver-tical position, it must be securedusing a strap.
Take extreme care when handling the hard top to avoid scratching ordamaging it. Do not lean the hard top against a wall or place it in an unstableposition. Store the hard top on a stand in a clean, dry environment and coverit. When the hood has been folded for a long time, ask a PEUGEOTdealer to remove any creases. Imperative The hard top heated rear screen harness must be connected at alltimes. If the harness is not con-nected significant damage mayresult from accidental operation.
The ignition must be switched off for all operations.
(except during the hood cover manoevring phase for the electric hood).
YOUR 306 CABRIOLET IN DETAIL 51
12
13
10
2

- Remove the retaining strap 2from
the hood cover 10.
- From the boot, close the hood cover 10manually. To do this,
remove the cap and turn the con- trol a quarter turn anti-clockwiseusing the wheelbrace. Removethe wheelbrace, reposition the capand close the boot.
Take care not to trap the harness.
- Carefully position the hard top: place the front edge of the roof incontact with the seal of the uppersection of the windscreen. Position the rear section of the roof on the side brackets 12.
Switch on the ignition. Open all the windows.
Lower the hood completely.
Switch off the ignition.Open the hood cover Place the restraining straps
2on the
two side flaps 7and the hood cover
10 .
- Secure the two side brackets 12to
the vehicle using the 17mm span- ner 6.
- Disconnect connector 8from the
harness located behind the sideflap 14on the right hand side of
the rear shelf.
HARD-TOP: REFITTING
Tools
Your hard-top is supplied with a tool kit containing: 1
- A storage case.
2 - Two retaining straps.
3 - A screwdriver with two heads.
4 - A pair of gloves.
5 - A special spanner.
6 - A 17mm flat spanner.
WARNINGThe removal-refitting operations described below should have beendemonstrated by your PEUGEOTdealer on handover of your vehicle. If your hard-top was supplied as
an accessory, the first removaloperation must be carried out by
an approved dealer. The opera-tion must be carried out by threepeople.
YOUR 306 CABRIOLET IN DETAIL
52
6
3
5 1 4
2
10
14
2
82
7
5
12

- Fit the covers 11in place and
screw them in.
- Check that the window seals are positioned correctly.
- Switch on the ignition and close the windows.
- Secure the two front side handles
13 .
- Secure the hard top on the side brackets 12using the special
spanner 5(a quarter turn).
- Connect connector 8to the hard
top heated rear screen harness.
- Remove the restraining strap 2
from the side flaps 7. Before folding the hood into its housing, ensurethat it has been brushedand dried to remove anymoisture and that the
rear screen is folded correctly.
To prevent damage to the hood cover and boot, the boot must beclosed during the hood cover low-ering and raising operations. Although the hood cover may appear to support itself in the ver-tical position, it must be securedusing a strap. Handle the hard top carefully so as not to damage the seal.
Take extreme care when handling the hard top to avoid scratching ordamaging it. Do not lean the hard top against a wall or place it in an unstableposition. Store the hard top on a stand in a clean, dry environment and coverit. When the hood has been folded for a long time, ask a PEUGEOTdealer to remove any creases. Imperative The hard top heated rear screen harness must be connected at alltimes. If the harness is not con-nected, significant damage mayresult from accidental operation.
The ignition must be switched off for all operations
(except during the hood cover manoeuvring phase for the electric hood).
YOUR 306 CABRIOLET IN DETAIL 53
11
13

YOUR 306 CABRIOLET IN DETAIL55
Ventilation 1 - Windscreen demisting or de-icing vents.
2 - Front windows demisting or de-icing vents.
3 - Side vents.
4 - Central vents.
5 - Air outlet to front footwells.
6 - Air outlet to rear footwells.
Advice on use
- Position the air flow control at a sufficient level to ensure correct renewal of air inside the vehicle.
- Select the most suitable air distribution for your requirements and the climatic conditions.
- Select a suitable temperature setting and only modify it gradually for your comfort.