ignition PEUGEOT 306 DAG 2002 User Guide

DC
EF
96
YOUR 306 IN DETAILAnti-lock braking system (ABS) warninglight* It comes on for 3 seconds
each time the ignition is switched on. If it comes on at over 8 m.p.h. (12 km/h.) it indicates a malfunction
of the ABS.
However, the vehicle retains conventional servo-assistedbraking.
Contact a PEUGEOT dealer.
* According to specification.
** According to model.
Oil level and temperature gauge* When the ignition is switched on, this indicates the oil level (see Oil Gaugesection). After approximately 15 seconds, the graduated section and the oil level
symbol go out. The oil temperature isthen shown.
- needle in zone
E, the temperature
is correct.
- needle in zone F, the temperature
is too high. To lower the oil temper- ature, reduce your speed.
Diesel pre-heat light If the light comes on, wait until it goes out before trying
the starter.
If the engine is warm enough, the lightwill not come on, and you can startthe engine without waiting. Front air bags*, sideair bags** anddisarming thepassenger air bag* For operation, see section on AIR BAGS.
Side air bags** For operation, see
section on AIR BAGS.
Oil gauge* When the ignition is switched on, this indicates the oil level: The reading is only valid if the vehicle is on level ground and the engine has
been switched off for 10 minutes.
- needle in zone
C, the oil level is
correct
- needle in zone D, check the oil level
using the dipstick and top up if nec-
essary.
Never exceed the maximum level onthe dipstick.
The oil level indicator switches off approximately 15 seconds after start-ing the engine.
Water in diesel filterwarning light(according to country) Risk of damage to the injection pump.
Contact a PEUGEOT dealer as soonas possible. Front brake pad wearwarning light*
For your safety, change the brake pads when thewarning light comes on.
Contact a PEUGEOT dealer.

DC
EF
96
YOUR 306 IN DETAILAnti-lock braking system (ABS) warninglight* It comes on for 3 seconds
each time the ignition is switched on. If it comes on at over 8 m.p.h. (12 km/h.) it indicates a malfunction
of the ABS.
However, the vehicle retains conventional servo-assistedbraking.
Contact a PEUGEOT dealer.
* According to specification.
** According to model.
Oil level and temperature gauge* When the ignition is switched on, this indicates the oil level (see Oil Gaugesection). After approximately 15 seconds, the graduated section and the oil level
symbol go out. The oil temperature isthen shown.
- needle in zone
E, the temperature
is correct.
- needle in zone F, the temperature
is too high. To lower the oil temper- ature, reduce your speed.
Diesel pre-heat light If the light comes on, wait until it goes out before trying
the starter.
If the engine is warm enough, the lightwill not come on, and you can startthe engine without waiting. Front air bags*, sideair bags** anddisarming thepassenger air bag* For operation, see section on AIR BAGS.
Side air bags** For operation, see
section on AIR BAGS.
Oil gauge* When the ignition is switched on, this indicates the oil level: The reading is only valid if the vehicle is on level ground and the engine has
been switched off for 10 minutes.
- needle in zone
C, the oil level is
correct
- needle in zone D, check the oil level
using the dipstick and top up if nec-
essary.
Never exceed the maximum level onthe dipstick.
The oil level indicator switches off approximately 15 seconds after start-ing the engine.
Water in diesel filterwarning light(according to country) Risk of damage to the injection pump.
Contact a PEUGEOT dealer as soonas possible. Front brake pad wearwarning light*
For your safety, change the brake pads when thewarning light comes on.
Contact a PEUGEOT dealer.

YOUR 306 IN DETAIL
58
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows "CODE"then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again. After 14 incorrectly input codes, the radio will be permanently locked and the display will read ÒENDÓ.
ADJUSTING THE SOUND Adjusting the volume
Turn the "M"button to increase or decrease the volume of the set.
In the event of the radio overheating, the volume reduces. If an attempt is made to increase the volume the message " TOO HOT ÕÕ appears on the display.
Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.

YOUR 306 IN DETAIL59
AUDIO SETTINGS Press the ÒAUDIOÓ button several times to select bass (BASS), treble (TREB) , loudness (LOUD), fader (FAD) and
balance (BAL).
Exit from audio mode is automatic after a few seconds, without pressing any button or by pressing the Ò AUDIOÓ
button after adjusting the balance. Note : bass and treble settings are speciflc to each source. It is possible to set them differently for radio,
cassette and CD.
Bass setting When Ò BASSÓ is displayed, press the Ò GÓ or Ò HÓ buttons to vary the setting.
ÑÒ BASS Ð9 Ó for a minimum bass setting,
ÑÒ BASS 0 Ó for a normal position,
ÑÒ BASS +9 Ó for a maximum bass setting.
Treble settingWhen Ò TREBÓ is displayed, press the Ò GÓ or Ò HÓ buttons to vary the setting.
ÑÒ TREB Ð9 Ó for a minimum treble setting,
ÑÒ TREB 0 Ó for a normal position,
ÑÒ TREB +9 Ó for a maximum treble setting.
Adjusting the loudness
This function automatically emphasises bass and treble tones when the volume is low. Press the ÒGÓor ÒHÓ buttons to switch this function on or off.
Setting the front/rear sound distribution (Fader) When Ò FA DÓ is displayed, press the Ò GÓ or Ò HÓ buttons to vary the setting.
The Ò GÓ button increases the volume at the front.
The Ò HÓ button increases the volume at the rear.
Note : For vehicles fitted with speakers at the front only, it is possible to cancel or add this function. This ope-
ration is carried out as follows:
- ignition key in Accessories position,
- with the radio switched off,- simultaneously pressing buttons ÒIÓand ÒMÓ.

68
YOUR 306 IN DETAIL
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. The set can operate for 30 minutes without switching the ignition on. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows " CODE IN" then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically. Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again. After 14 incorrectly input codes, the radio will be permanently locked and will display ÒENDÓ.
ADJUSTING THE SOUND Adjusting the volume
Turn the "ON/VOL" button Mto increase or decrease the volume of the set.
In the event of the radio overheating, the volume level decreases. Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.

55
4 - Adjusting the air flow
In the AUTO position the flow is controlled automatically in accordancewith the temperature selected.
You can, however, adjust the flow manually by turning the knob 4accor-
ding to the desired flow.
In AUTO mode, this automatically adjusts the temperature inside thevehicle according to your wishes (pre-
set temperature). To do this, the elec-tronic control unit adjusts the tempe-rature and the flow of air at the ventsand operates the air conditioning
system if necessary. 5 - Recirculation of interior air Press the switch 5, the indicator light
comes on.The air conditioning comes into ope-
ration automatically. This position must only be used in exceptional circumstances to:
- improve the performance of the air conditioning,
- prevent the entry of external air (dust, unpleasant odours),
- speed up heating inside the vehicle with a risk of misting of the windows. Special features If the air distribution control is in the windscreen de-icing position, the airconditioning system will start opera-ting automatically when the engine isswitched on.
If the air flow control is in the AUTO position, and air recirculation is selec-ted, air conditioning will start automa-tically in order to prevent condensa-tion on the windows. When you switch on the ignition, the air conditioning will automaticallyreturn to the operating mode it was inwhen it was last used. If the inside
temperature is greatly different fromthe required temperature displayedand the outside temperature is above5 ¡C the air conditioning will switch onautomatically regardless of the posi-tion of the air flow control. When the ignition is switched on, if the system had been in air recirculationmode, the system will automaticallyallow entry of outside air unless thetemperature inside the vehicle is over30 ¡C.
Important precautions Operate the air conditioning system for 5 to 10 minutes once or twice amonth to keep it in good working
order. It is advisable to change the air condi- tioning system fluid every 2 years.
If the system is not producing cold air, stop using it and contact a
PEUGEOT dealer.
YOUR 306 IN DETAIL

1
89
YOUR 306 IN DETAIL
To adjust the height of the front seat belts Pull the knob 1and slide it.
To lock the seat beltsPull the strap, then insert the end into the buckle. Pre-tensioning and force-limiting front seat belts* Safety in the event of a frontal impact has been improved by the introduc-tion of pre-tensioning and force-limit-ing front seat belts. Depending on theseriousness of the impact, the pre-tensioning system instantly tightensthe seat belts firmly against the bodyof the occupant. The pre-tensioning seat belts are armed when the ignition is on. The force-limiting device reduces the pressure of the seat belt against the
occupantÕs body in the event of anaccident. Rear seat belts 4-door:
the rear seats are fitted with
3 three-point inertia reel seat belts.
3/5-door, estate: The rear seats are
fitted with 2 three-point inertia reel seat belts and one lap belt. Use the buckle retaining hooks when the rear seats are not occupied.
* According to specification. To be effective, a seat belt must be tensioned asclose to the body as pos-sible.
Depending on the nature and seri-ousness of the impact the pre-ten-sioning system may be triggeredbefore and independently of theairbags. In all cases, the airbag warning light comes on. Following an impact, have the system checked by a PEUGEOT
dealer. The system has been designed to be fully operational for ten years. Have it replaced at the end of this period.
SAFETY: SEAT BELTS

YOUR 306 IN DETAIL
78
THE REMOTE CONTROL
A single press on button Alocks the
doors and boot or tailgate, this is dis- played by the direction indicatorsstaying on for about 2 seconds.
A single press on button Bunlocks the
vehicle, this is displayed by the direc-
tion indicators flashing rapidly.
KEYS
Without central locking The key individually Iocks and unlocks the doors and boot or tailgate.
With central locking
Turning the key in the driverÕs door lock will lock or unlock the doors andboot or tailgate. If either of the frontdoors is not closed, the central lockingwill not work. CHANGING THE REMOTE
CONTROL BATTERIES
To gain access to the battery, unclip the key casing with a coin where youcan see the ring (CR1620/3 volt battery). If the remote control does not work after the battery has been changed,re-programme the remote control. PROGRAMMING THE REMOTE CONTROL Manual synchronisation
- Switch off the ignition,
- Switch on the ignition,
- Immediately after switching on the
ignition press button A.
The remote control is now working again. Automatic synchronisation
- Switch on the ignition (position M),
- Switch off the ignition and, during the next four minutes, lock the vehicle using the remote control(button A).
The remote control is now workingagain.
Note: do not repeatedly press the
button of your remote control out of
range of your vehicle. You risk causingit not to work and the remote controlwould have to be reprogrammed.
A
B

A
79
YOUR 306 IN DETAIL
DOORS Opening the doors from outside
Take careful note of the numbers on the keys. The key number is coded on the label attached to
the key. If the key is lost
your PEUGEOT dealer can rapidlysupply you with new keys or aremote control. As a safety precaution (with chil- dren on board) remove the ignitionkey when you leave the vehicle,even for a short time. The high frequency remote control is a high-performance systemwhich has a powerful beam. There-fore do not operate it while it is inyour pocket as there is a possibil-ity that it may unlock your vehicle.
Opening the doors frominside LOCKING FROM INSIDE THEVEHICLE
Without central locking
To lock, press button
A. The button
locks that door.
With central locking
To lock, press button A.
Locking the driverÕs door locks the front and rear doors and the tailgate. On the other doors the button only
locks that door.

80
YOUR 306 IN DETAIL
Locking or unlocking the boot or tailgate 3 or 5 door without central locking
Turn the key in the tailgate lock. 4 door or estate Using the key: turn the key in the boot or tailgate lock. Using the remote control*: the boot or tailgate locks and unlocks at the sametime as the doors. Locking the boot only (4 door)
Turn the key to the right in the boot lock. The boot will be locked whatever the action of the remote control or the
driverÕs door lock.
To open, turn the key to the left in the
boot lock. The boot will then be lockedat the same time as the central lockingof the doors. The seat back locking control enables you to prevent unauthorised entry tothe boot, even if the doors are open. Locking or unlocking the bootor tailgate 3 or 5 door with central locking The tailgate locks and unlocks at the same time as the doors.
Tailgate release In the event of a central locking oper- ating fault, this enables the tailgate tobe unlocked:
- fold the rear seats to gain access
to the control from inside the vehicle.
- Insert the ignition key in the opening and slide it to unlock the tailgate.
Child lock This prevents opening of the rear doors from inside the vehicle.
Turn control 1a quarter turn using the
ignition key. It is still possible to open the doors from outside the vehicle.
* According to specification.
1