ECU Peugeot 307 2007.5 Owner's Manual

COMFORT
54
5. Head restraint height and angle adjustment
To raise the head restraint, pull it up-
wards.
To remove the head restraint, press
the lug A and pull the head restraint
upwards.
To put the head restraint back in po-
sition, locate the stems of the head
restraint in the holes, taking care to
keep them in line with the seat back.
To lower the head restraint, press the
lug A and the head restraint.
The head restraint frame has a catch
which prevents it from lowering; this
safety device provides protection in
the event of an impact.
To tilt the head restraint, tilt the lower
part forwards or backwards.
REAR HEAD RESTRAINTS
Never drive with the head
restraints removed; they
should be in place and cor-
rectly adjusted.
These have a high position for when
they are in use and a low position for
when they are stored.
The head restraints are removable.
To remove them, pull upwards as far
as the stop then press the lug.
6. Armrests
These can be folded down and are
removable.
To remove them, press the button lo-
cated between the armrest and the
side of the seat and pull it.
7. Storage drawers
There is a storage drawer under each
front seat.
- To open it, lift it and pull.
- To take it out, open it to its full ex-
tent, press the ends of the slides
and lift it, then remove it com-
pletely.
- To put it back in place, at the end of its travel, press on the top of
the drawer to secure it.
Under the front passenger seat, the
layout of the l oor allows for storage
of a i rst aid kit and a warning triangle
(small version).

The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head. Do not place heavy objects
in the drawers.

59
COMFORT
LOCATION OF CHILD SEATS SECURED USING THE SEAT BELT
In accordance with the European regulation (Directive 2000/3), this table indicates the options for the installation of child seats
secured using the seat belt and universally approved (a) dependi ng on the weight of the child and the seat in the vehicle:
(a) Universal child seat: child seat which can be installed in all vehicles using the seat belt.
(b) Group 0: from birth to 10 kg.
(c) Consult the current legislation in your country before instal ling your child on this seat.

U : seat suitable for the installation of a child seat secu red using the seat belt and universally approved, "rear facing" a nd/or
"forwards facing".

U (R) : identical to U , but the vehicle seat must be adjusted to the highest po sition.
Seat
Weight of the child /indicative age
Below 13 kg(groups 0 (b) and 0+) Up to 1 year approx
9 to 18 kg (group 1) 1 to 3 years approx
15 to 25 kg (group 2) 3 to 6 years approx
22 to 36 kg (group 3) 6 to 10 years approx
Front passengerseat (c)
- i xed
-
height adjustable (R)
U

U (R)
U

U (R)
U

U (R)
U

U (R)
Rear side seats
U U U U
Rear centre seat U U U U

61
COMFORT
These are two rings located between
the seat back and the seat cushion.

The ISOFIX child seats are i tted
with two locks which are secured
easily on these rings. These seats are i tted with ISOFIX
mountings. This ISOFIX mounting system guar-
antees reliable, safe and fast i tting of
the child seat in your vehicle.

COMFORT
62
These child seats can also be used on seats which are not i tted with ISOFIX mountings. In this case, it is essential
that they are secured to the vehicle's seat by means of the thre e point seat belt.

Follow the instructions for i tting the child seat indicated in the seat manufacturer's installation guide.
ISOFIX CHILD SEATS RECOMMENDED BY PEUGEOT AND APPROVED FOR YOUR VEHIC LE
ISOFIX KIDDYISOFIX RÖMER Duo Plus
Group 0+: from birth to 13 kgGroup 1: from 9 to 18 kgGroup 1: from 9 to 18 kg
Installed in the rear facing position. Installed in the forwards facing position. Installed in the forwards facing position only.
The body of the child seat must be in contact with the back of the vehicle's front seat.
It is essential that the vehicle's front seat is adjusted to the intermediate lon-gitudinal position.
Secured without the top strap.
Three child seat body angles: sitting, reclining and lying positions.
Adjust the vehicle's front seat so that the child's feet do not touch the seat back.

LAYOUT
85

1. Rear parcel shelf
To remove the shelf:
- unhook the two strings,
- slightly raise the shelf, then remove it.
The shelf can be stored:
- either behind the front seats,
- or behind the rear seat.

2. Hooks

3. Stowing rings
4. Luggage retaining net
Hooked onto the stowing rings, this
enables your luggage to be secured.

5. Open storage trays

6. 12 volt socket (100 W max)
This is a lighter type socket, installed
on the left-hand side of the parcel
shelf.
It is supplied from the "Running"
position.
BOOT LAYOUT (SALOON)

LAYOUT
87
BOOT LAYOUT (ESTATE)
4. Boot l oor and pillar stowing rings
5. Rear seat stowing rings
6. Luggage retaining net
Secure the net hooks in the stowing
rings on the l oor or on the folded
rear seat (two horizontal positions) or
secure the net hooks in the stowing
rings on the boot pillars and in the
l oor rings at the rear of the boot (one
vertical position).
7. 12 volt socket (100 W max)
This is a lighter type socket, installed
on the load space cover left support.
It is supplied from the "Running"
position. 8. High load retaining net i xings
The high load retaining net can be
installed behind the front or rear
seats.
Open the covers of the corresponding
upper i xings.
Fit the ends of the metal bar in these
i xings.
To install the high load retaining net:
- behind the front seats, lift the rear
seat cushion, hook the net straps
on the i xings then fold the rear
seat;
- behind the rear seat, hook the net straps in the stowing rings on the
l oor.
The rings are located directly below
the corresponding upper i xings.
Pull the two straps taut.
9. Grab handles and coat hooks
1. Load space cover
To install it:
- position the front ends of the
cover on its support and press
gently to put it in place,
- unfold the cover fully,
- position the rear ends of the cover on its support and press gently to
put it in place.
To remove it:
- unclip the rear ends,
- fold the cover fully,
- unclip the front ends and remove the cover.
To store it, slide it under the rear
seats (location A ).
2. Floor storage trays (2/3 - 1/3)
3. Storage nets
One of them contains the luggage
retaining net.

SAFETY
93
Wherever you are seated in
the vehicle, always fasten
your seat belt, even for short
journeys. In order to be effective, a seat belt:
- must be tightened as close to the
body as possible,
- must restrain one adult only,
- must not bear any trace of cuts or fraying,
- must be pulled in front of you with a smooth movement, checking
that it does not twist,
- must not be transformed or modii ed to avoid altering its performance.
In accordance with current safety
regulations, all repairs and checks
must be carried out by a PEUGEOT
dealer who guarantees that the work
is carried out correctly.
Have your seat belts checked regu-
larly by a PEUGEOT dealer and par-
ticularly if the straps show signs of
damage.
Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by PEUGEOT dealers.
After folding or moving a seat or rear
bench seat, ensure that the seat belt
is positioned and rolled up correctly. Recommendations for children:
- use a suitable child seat if the pas-
senger is less than 12 years old or
shorter than one metre i fty,
- do not use the strap-guide * when a child seat is installed.
- never use the same seat belt to secure more than one person,
- never allow a child to travel on your lap.

Depending on the nature and se-
riousness of the impacts , the pre-
tensioning device may be triggered
before and independently of the air
bags. Triggering of the pre-tensioners
is accompanied by a slight emission
of harmless smoke and a noise, due
to the activation of the pyrotechnic
cartridge incorporated in the system.
In all cases, the air bag warning light
comes on.
Following an impact, have the seat
belts system checked, and if neces-
sary replaced, by a PEUGEOT dealer.
Do not invert the seat belt buckles as
they will not fuli l their role fully.
If the seats have armrests * , the lap
part of the seat belt must always
pass under the armrest.
The seat belts are i tted with an inertia
reel permitting automatic adjustment
of the length of the strap to your size.
The seat belt is stored automatically
when not in use.
Before and after use, ensure that the
seat belt is rolled up correctly.
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in
the hollow of the shoulder.
The inertia reels are i tted with an au-
tomatic locking device which comes
into operation in the event of a colli-
sion, on emergency braking or if the
vehicle rolls over. You can release
the device by pulling rapidly on the
strap and releasing it.

CHECKS
109
Tilt the handle on the left-hand side
under the fascia to the right.
Lift the catch and raise the bonnet. Secure the strut
to hold the bonnet
open.

Before closing the
bonnet, replace the
strut in its housing.

RUNNING OUT OF FUEL
(DIESEL)
If you should run out of fuel, it is nec-
essary to re-prime the circuit.
The repriming pump, the degas
screw and the transparent pipe are
located under the bonnet (see corre-
sponding drawing):
OPENING THE BONNET
From inside
From outside
Bonnet strut
To close
Lower the bonnet and release it at
the end of its travel.
Check that the bonnet is properly
locked.
1.6 litre HDI 16V engine
- i ll the fuel tank with at least i ve
litres of diesel,
- unclip the style cover to access the repriming pump,
- squeeze and release the manual repriming pump until fuel appears
in the transparent pipe with the
green connector,
- operate the starter until the engine starts.
2 litre HDI 16V engine
- i ll the fuel tank with at least i ve litres of diesel,
- unclip the style cover to access the repriming pump,
- unscrew the degas screw,
- squeeze and release the manual repriming pump until diesel is
seen escaping via the degas
screw,
- retighten the degas screw,
- operate the starter until the engine starts.

10PRACTICAL INFORMATION
123
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool 6 to remove the
trims before slackening the bolts. Wheel with centre trim
Fitting snow tyres
If you i t snow tyres mounted on
steel wheels onto your vehicle, it
is essential to use special bolts
available from your PEUGEOT
dealer.
 slide the trim remover 7 into the
notch of the centre trim,

 use the trim remover as a lever
pressing on the trim to unclip it,

 unscrew the bolt using the anti-
theft socket and the wheelbrace.
If your vehicle is i tted with a steel
spare wheel, when i tting it, it is

normal when tightening the bolts to
notice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
This anti-theft socket was
given to you on delivery
of your vehicle along with
the duplicate keys and the
coni dential card.
Make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate socket from a
PEUGEOT dealer.
Special features of alloy wheels
Fitting the spare wheel
Anti-theft bolts
Your wheels are i tted with an anti-
theft bolt, one per wheel.
Bolt covers
Wheel with chrome trim

 remove the chrome trim,

 unscrew the bolt using the anti-
theft socket and the wheelbrace.

10PRACTICAL INFORMATION
122
Fitting a wheel

 Position the wheel using the
centralising tool 5 to assist you.

 Tighten the bolts by hand and
remove the centralising tool 5 .

 Partly tighten the bolts using the
wheelbrace 1 .

 Fold the jack 4 and remove it.

 Fully tighten the bolts using the
wheelbrace 1 .

 Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.

 Put the corresponding tools in the
holder and secure its cover.

 Place the holder on the ground
and align the spare wheel on it.

 Pass the notched hook into the
holder cover.

 Rei t the wheel under the vehicle
tightening the winch control nut
using the wheelbrace 1 .

 Fully tighten and check that
the wheel is horizontally l ush
against the rear l oor .

 Close the l ap using the lug to
lock the winch.

 Store the rest of the tools in the
right-hand trim of the boot.
For your safety, always
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ignition switched off,
- with i rst or reverse gear engaged (position P for the automatic
gearbox),
- with the vehicle chocked.

Never go underneath a vehicle that
is supported only by a jack (use a
ramp).

Never rei t the holder under the
vehicle without the spare wheel.

Do not use a screwdriver in place
of the wheelbrace to unwind or
wind the winch. Recommendations when using
the temporary spare wheel *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, it must be replaced as
quickly as possible.
Observe the following instructions to
avoid altering the behaviour of the
vehicle:
-
do not exceed
50 mph (80 km/h) ,
- do not i t a wheel trim,
- drive with care,
- check the tyre pressure indicated
on the label.
After changing the wheel:
- have the correct positioning of the
punctured wheel, the tightening
of the bolts and the tyre pressure
checked by a PEUGEOT dealer
as soon as possible,
- have the punctured tyre repaired and rei t it to the vehicle as soon
as possible,
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer.
Wheels i tted with the Tyre Under-
Inl ation Detection system
For further information refer to "Tyre
under-inl ation detection" in the
safety section.
* According to model and country.