bulb Peugeot 307 2007.5 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2007.5, Model line: 307, Model: Peugeot 307 2007.5Pages: 212, PDF Size: 7.59 MB
Page 84 of 212
VISIBILITY
75
F o r v e h i c l e s i t t e d w i t h h a l o g e n
bulbs, depending on the load in your
vehicle, adjusting the beam of your
headlamps is recommended.
0. 1 or 2 people in the front seats.
- . 3 people.
1. 5 people.
2. 5 p e o p l e + m a x i m u m a u t h o r i s e d
loads.
3.
D r i v e r + m a x i m u m a u t h o r i s e d l o a d s .
Initial setting is position 0. O n v e h i c l e s w i t h x e n o n b u l b s :
w h e n s t a t i o n a r y , the system automatically
corrects the height of the beam, whatever
the load of the vehicle. The driver is then
assured of having optimum lighting and
not causing a
nuisance to other road
users.
I n c a s e s o f m a l f u n c t i o n ,
the service warning light
comes on on the instrument
panel, accompanied by
an audible signal and a
message on the multifunction display.
The system places your headlamps
to the low position.
D o n o t t o u c h t h e x e n o n b u l b s .
Contact a PEUGEOT dealer.
D a y t i m e l i g h t s *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunction
display, air conditioning control
panel, ...) are only lit on switching
to the automatic switching on of the lights
mode or when the lights are switched on
manually.
This warning light comes
on on the instrument panel.
MANUAL ADJUSTMENT OF
THE HEADLAMPS
A U T O M A T I C H E A D L A M P
ADJUSTMENT
* According to country.
Page 127 of 212
CHECKS
115
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r i l l p a s t t h i s m a r k .
B = minimum
Oil change
According to the information given in
the servicing booklet.
Viscosity selection
In all cases, the oil selected must
meet the manufacturer’s require-
ments.
Note: the coolant does not need to
be changed.
Dipstick
Cooling system
U s e t h e l u i d r e c o m m e n d e d b y t h e
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. This fan can oper-
ate with the ignition off.
I n t h e c a s e o f v e h i c l e s i t t e d w i t h
a p a r t i c l e e m i s s i o n i l t e r , t h e f a n
can operate after the vehicle has
s t o p p e d , e v e n w h e n t h e e n g i n e i s
cold.
In addition, as the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level.
Windscreen and headlamp
w a s h l e v e l
Diesel additive level (Diesel
w i t h p a r t i c l e e m i s s i o n f i l t e r )
If the service warning light comes on,
accompanied by a message and an
audible signal, this indicates a low
diesel additive level.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
Brake fluid level
* According to engine.
Oil level
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited.
The level should always be
above the MIN mark and
close to the MAX mark.
P o w e r s t e e r i n g r e s e r v o i r
Remove the style trim * (see §
"Changing a bulb - Front lights").
Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
For best quality cleaning and
for your safety, we would ad-
vise that you use products
recommended by PEUGEOT.
Check the level regularly and
top up between changes. The
maximum consumption is 0.5 l
per 600 miles (1 000 km).
Check the level with the ve-
hicle level, engine cold, using the oil
level gauge on the instrument panel
or the dipstick. Replacement must be car-
ried out according to the
manufacturer’s servicing
schedule.
U s e l u i d s r e c o m m e n d e d b y
t h e m a n u f a c t u r e r , w h i c h f u l i l D O T 4
standards.
Page 138 of 212
10PRACTICAL INFORMATION
124
Front lights
In the engine compartment, on the
right-hand side, remove the style
trim * :
- press the centre of each plastic stud A ,
- remove each plastic stud,
- remove the style trim.
W h e n y o u h a v e i n i s h e d , d o n o t
forget to put everything back in place
correctly:
- position the style trim * ,
- r e i t e a c h p l a s t i c s t u d A by
pressing on it. Handle the bulbs with a dry
cloth.
T h e h e a d l a m p s a r e i t t e d
with polycarbonate glass with
a protective coating. D o n o t c l e a n
t h e m w i t h a d r y o r a b r a s i v e c l o t h ,
n o r w i t h a d e t e r g e n t o r s o l v e n t
p r o d u c t .
Use a sponge and soapy water.
1 . D i p p e d b e a m h e a d l a m p s
( H 1 - 5 5 W o r x e n o n b u l b ) .
W A R N I N G : R I S K O F E L E C T R O -
C U T I O N
Xenon bulbs must be changed by a
PEUGEOT dealer.
2. M a i n b e a m h e a d l a m p s ( H 7 - 5 5 W ) .
Remove the protective cover
corresponding to the faulty bulb.
Disconnect the connector.
Press the end of each securing
clip. Change the bulb.
W h e n i t t i n g t h e n e w b u l b , e n s u r e that the direction notches are
positioned correctly and the
s e c u r i n g c l i p s a r e i x e d p r o p e r l y .
Reconnect the connector.
R e i t t h e p r o t e c t i v e c o v e r .
C H A N G I N G A B U L B
* According to engine.
Page 139 of 212
10PRACTICAL INFORMATION
125
I n t e g r a t e d d i r e c t i o n i n d i c a t o r s i d e
repeaters.
Push the repeater forwards and
release it.
Remove the repeater and change
it.
These can be obtained from a
PEUGEOT dealer.
Amber coloured bulbs, such
as the direction indicators,
must be replaced with bulbs
o f i d e n t i c a l s p e c i i c a t i o n a n d
colour.
3 . S i d e l i g h t s ( W 5 W ) .
Remove the protective cover
corresponding to the faulty bulb.
Disconnect the connector.
Remove the bulb and change it.
4 . D i r e c t i o n i n d i c a t o r s (PY 21 W amber).
Turn the bulb holder a quarter of
a turn and remove it.
Change the bulb.
Note
: in certain climatic conditions
(low temperature, humidity), c o n d e n -
s a t i o n i n s i d e t h e h e a d l a m p g l a s s i s
normal ; it disappears a few minutes
after the lights are switched on.
5 . F o g l a m p s ( H 1 1 - 5 5 W ) .
Contact a PEUGEOT dealer to have
these bulbs changed.
Page 140 of 212
10PRACTICAL INFORMATION
126
1. D i r e c t i o n i n d i c a t o r s ( P 2 1 W ) .
2. R e v e r s i n g l i g h t s ( P 2 1 W ) ,
l e f t - h a n d s i d e .
F o g l a m p ( P 2 1 W ) , r i g h t - h a n d
s i d e .
3. Brake lights (P 21 W).
4. S i d e l i g h t s ( x 2 ) ( R 5 W ) .
Using a 10 mm box spanner,
u n s c r e w t h e 2 i x i n g n u t s 1 .
Release the lamp unit by pushing
it outwards.
Squeeze the two tabs 2 to release
the bulb holder.
Change the faulty bulb.
W h e n r e i t t i n g , e n s u r e t h a t t h e
lamp unit seal has been put back
in place correctly.
These 6 bulbs are changed from
inside the boot:
Move aside the boot trim to
access the bulb holder,
Press the two tabs and remove
the bulb holder,
Change the faulty bulb.
W h e n r e i t t i n g , t a k e c a r e t o p a s s t h e
trim under the seal.
Rear lights (saloon) T h i r d b r a k e l i g h t ( s a l o o n )
(4 W 5 W bulbs)
Page 141 of 212
10PRACTICAL INFORMATION
127
Remove the tailgate upper trim
carefully by unclipping it on either
side, perpendicular to its direction
of engagement.
Insert a screwdriver into the two
outer holes B to press on the two
tabs C .
Push the light unit outwards while
maintaining the pressure on the
tabs.
Pull the light unit outwards while
tilting it.
Change the faulty bulb.
W h e n r e i t t i n g , e n s u r e t h a t t h e
light unit tabs are engaged
correctly and that the tailgate
upper trim has been put back in
place correctly.
1. Brake lights (P 21 W).
2. S i d e l i g h t s ( x 2 ) ( R 5 W ) .
3. D i r e c t i o n i n d i c a t o r s ( P 2 1 W ) .
4. R e v e r s i n g l i g h t ( P 2 1 W ) ,
l e f t - h a n d s i d e .
F o g l a m p ( P 2 1 W ) , r i g h t - h a n d
s i d e .
These 6 bulbs are changed by
removing the light:
Remove the corresponding boot
side trim to access the light,
R e m o v e t h e l i g h t i x i n g n u t i n s i d e
the boot,
R e m o v e t h e l i g h t i x i n g n u t o u t -
side the boot,
Remove the light,
Unclip the harness,
Remove the bulb holder pressing
on the tabs A ,
Change the faulty bulb.
Note: if necessary, use the wheel-
brace to remove the nuts.
W h e n r e i t t i n g , t a k e c a r e t o p o s i t i o n
the bulb holder and the light
correctly.
Number plate lights
(W 5 W)
Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Change the faulty bulb.
Rear lights (estate) T h i r d b r a k e l i g h t ( e s t a t e )
(4 W 5 W bulbs)
Page 153 of 212
10PRACTICAL INFORMATION
138
A C C E S S O R I E S F O R Y O U R 3 0 7
A wide range of accessories recom-
mended by PEUGEOT and original
parts are offered by the network.
T h e y a l l b e n e i t f r o m P E U G E O T ’ s
recommendation.
These accessories and parts, having
been tested and approved for reli-
ability and safety, are all adapted to
your PEUGEOT vehicle.
The product range offered by
PEUGEOT Accessories is structured
around 5 categories: PROTECTION -
TOURING - IN-CAR TECHNOLOGY -
STYLING - UNIVERSAL, it is dedicated
to:
"Touring":
mats, boot tray, luggage
n e t , i x e d c o a t h o o k o n
head restraint, aluminium
or PVC door sills.
For leisure pursuits: roof
bars, tailgate bicycle car-
rier * (estate), bicycle carrier on roof
bars, ski carrier, roof box, booster
seats and child seats, side blinds
and rear blind, front centre armrest,
CD storage, under shelf storage (sa-
loon).
T r a i l e r t o w b a r w h i c h m u s t b e i t t e d b y
the PEUGEOT network.
T h e i t t i n g o f e l e c t r i c a l e q u i p -
ment or accessories which
are not recommended by
PEUGEOT may result in a
failure of your vehicle’s electronic
system.
P l e a s e n o t e t h i s s p e c i i c w a r n i n g .
You are advised to contact a repre-
sentative of the Marque to be shown
the range of recommended equip-
ment and accessories. " U n i v e r s a l " :
screenwash, interior and
exterior maintenance and
cleaning products.
"Protection":
anti-theft alarm, window en-
g r a v i n g , w h e e l l o c k s , i r s t
aid kit, warning triangle,
safety jacket, stolen vehicle
tracking system, dog guard,
snow chains. " I n - c a r t e c h n o l o g y " :
audio systems, audio/tele-
p h o n e , a m p l i i e r s , s a t e l l i t e
navigation systems, hands-
free kit, entertainment
screen kit, CD changer,
speakers, DVD player, con-
nection kit for MP3 player or portable
CD player, rear parking assistance. " S t y l i n g " :
seat covers compatible with
side air bags, aluminium
gear lever knob, fog lamps,
d o o r d e l e c t o r s , s p o i l e r
(saloon), styling strips, al-
loy wheels, trims, sport ex-
haust.
* When using a tailgate bicycle car- rier, deactivate the rear wiper via
t h e m u l t i f u n c t i o n d i s p l a y c o n i g u -
ration menu.
Note
To avoid any risk of jamming of the
pedals:
- ensure that the mat is positioned and secured correctly,
-
n e v e r i t o n e m a t o n t o p o f a n o t h e r .
Depending on the country
in which the vehicle is sold,
it is compulsory to have a
high visibility safety jacket, a
warning triangle and a set of spare
bulbs available in the vehicle.