turn signal Peugeot 307 2007.5 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2007.5, Model line: 307, Model: Peugeot 307 2007.5Pages: 212, PDF Size: 7.59 MB
Page 17 of 212
INSTRUMENTS and CONTROLS
20
OPERATION WARNING
LIGHTS
A permanently lit warning light or
o n e t h a t l a s h e s w i t h t h e e n g i n e
r u n n i n g , i n d i c a t e s a n o p e r a t i n g f a u l t
in the relevant unit. Some warning
l i g h t s m a y b e l i n k e d t o b u z z e r s a n d
a m e s s a g e o n t h e m u l t i - f u n c t i o n
d i s p l a y . D o n o t i g n o r e t h i s w a r n i n g :
c o n t a c t a P E U G E O T d e a l e r a s s o o n
a s p o s s i b l e .
I f t h e C e n t r a l S T O P w a r n i n g l i g h t
c o m e s o n w h e n y o u a r e d r i v i n g ,
s t o p i m m e d i a t e l y w h e r e i t i s s a f e
t o d o s o .
Central STOP
warning light
This light comes on
for a few seconds
each time the igni-
tion is switched on.
It is linked to the "engine oil pres-
s u r e " * , " l o w b r a k e l u i d l e v e l " a n d
"electronic brake force distribution
fault" warning lights and the coolant
temperature gauge.
S t o p i m m e d i a t e l y i f i t l a s h e s w i t h
the engine running.
Contact a PEUGEOT dealer.
It also comes on in the event of a
puncture,accompanied by an audible
signal and a message on the multi-
function display locating the wheel
concerned. Service warning light
This light comes on for a
few seconds each time
the ignition is switched on.
If it remains on or comes
on when the engine is running, ac-
companied by an audible signal and
a message on the multifunction dis-
play, it indicates one of the following:
- a battery charge fault * ,
- an automatic gearbox operation fault,
- an engine immobiliser system fault,
- an engine management system fault,
- a speed control system fault (cruise control/speed limiter),
- a rear parking assistance system fault,
- an automatic switching on of the lights system fault,
- an automatic headlamp height adjustment system fault,
- a t y r e u n d e r - i n l a t i o n d e t e c t i o n system fault,
- a d e l a t e d w h e e l ,
- a l a t r e m o t e c o n t r o l b a t t e r y ,
-
one or more door(s) open at a vehi-
cle speed above 6 mph (10 km/h),
- a low diesel additive reservoir level (Diesel),
- a lack of engine oil,
- the start of saturation of the par- t i c l e e m i s s i o n i l t e r ( D i e s e l ) d u e
to exceptionally prolonged urban
driving conditions: low speed,
l o n g t r a f i c j a m s , . . . I n o r d e r t o r e g e n e r a t e t h e i l -
ter, you are advised to drive at
a speed of 40 mph (60 km/h) or
a b o v e f o r a t l e a s t i v e m i n u t e s
(until the warning light is switched
off) as soon as possible, when
t r a f i c c o n d i t i o n s p e r m i t . I f t h e
warning light remains on, contact
a PEUGEOT dealer.
During regeneration of the par- t i c l e e m i s s i o n i l t e r , r e l a y n o i s e
may be heard from underneath
the fascia.
- the presence of water in the die- s e l i l t e r ( D i e s e l ) * .
R i s k o f d a m a g e t o t h e i n j e c t i o n
s y s t e m .
Contact a PEUGEOT dealer as soon as possible.
- a low coolant level ** .
Stop immediately.
Warning: wait for the engine to cool
before topping up the level. The cool-
ing system is pressurised.
In order to avoid any risk of scalding,
unscrew the cap by two turns to allow
the pressure to drop. When the pres-
sure has dropped, remove the cap
and top up the level.
Contact a PEUGEOT dealer.
** According to engine.
* According to country.
Page 20 of 212
INSTRUMENTS and CONTROLS
23
Coolant temperature indicator Engine oil temperature gauge
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B , the tem-
perature is too high. The central STOP
w a r n i n g l i g h t l a s h e s , a c c o m p a n i e d b y
an audible signal and a message on
the multifunction display.
Y o u m u s t s t o p i m m e d i a t e l y .
Warning: wait for the engine to cool
before topping up the level.
The cooling system is pressurised.
In order to avoid any risk of scalding,
unscrew the cap two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level.
Contact a PEUGEOT dealer. When the engine is running, this indi-
cates the oil temperature.
The temperature is too high if the
maximum graduation is reached.
Y o u m u s t s t o p i m m e d i a t e l y .
Contact a PEUGEOT dealer.
P a r k
A u t o m a t i c g e a r b o x l e v e r
p o s i t i o n s i n d i c a t o r
R e v e r s e
Neutral
Drive
Manual mode:
1
s t gear engaged
2
nd gear engaged
3
rd gear engaged
4
th gear engaged
5
th gear
engaged
***
6
th gear engaged ***
*** According to model.
Page 67 of 212
ACCESS
64
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by any-
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi-
ble.
If the system does not function
correctly, the service warning light
comes on, accompanied by an audi-
ble signal and a message on the mul-
tifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
A heavy object attached to the key
(key ring, ...), weighing down on the
shaft of the key in the switch, may
cause a malfunction.
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y l a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible sig-
nal and a message on the multifunc-
tion display.
To replace the battery, unclip the cas-
ing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the driv-
er’s door, if the key has been left in
the ignition.
control battery or in the event of a re-
mote control malfunction, the remote
control must be reinitialised.
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few sec-
onds.
Switch off the ignition and remove
the remote control key from the
ignition lock.
The remote control is now working
again.
Locating your vehicle
Using the key
Turn the key in the lock on the
driver’s door to lock the vehicle.
T u r n t h e k e y a g a i n w i t h i n i v e
seconds to deadlock the vehicle.
E a c h a c t i o n i s c o n i r m e d b y i x e d
lighting of the direction indicators for
approximately two seconds.
When the vehicle is locked,
if unlocking is activated inad-
vertently without a door being
opened within 30 seconds,
the vehicle will lock automatically.
The folding and unfolding of the ex-
terior mirrors can be deactivated by
a PEUGEOT dealer.
To locate your vehicle, if
you have locked it, in a
car park:
press button B , the courtesy lights
come on and the direction indica-
t o r s l a s h f o r a f e w s e c o n d s .
Changing the remote control
battery
Reprogramming the remote
control
Following disconnection of the vehi-
cle’s battery, replacement of the remote
Page 69 of 212
ACCESS
64
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by any-
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi-
ble.
If the system does not function
correctly, the service warning light
comes on, accompanied by an audi-
ble signal and a message on the mul-
tifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
A heavy object attached to the key
(key ring, ...), weighing down on the
shaft of the key in the switch, may
cause a malfunction.
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y l a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible sig-
nal and a message on the multifunc-
tion display.
To replace the battery, unclip the cas-
ing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the driv-
er’s door, if the key has been left in
the ignition.
control battery or in the event of a re-
mote control malfunction, the remote
control must be reinitialised.
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few sec-
onds.
Switch off the ignition and remove
the remote control key from the
ignition lock.
The remote control is now working
again.
Locating your vehicle
Using the key
Turn the key in the lock on the
driver’s door to lock the vehicle.
T u r n t h e k e y a g a i n w i t h i n i v e
seconds to deadlock the vehicle.
E a c h a c t i o n i s c o n i r m e d b y i x e d
lighting of the direction indicators for
approximately two seconds.
When the vehicle is locked,
if unlocking is activated inad-
vertently without a door being
opened within 30 seconds,
the vehicle will lock automatically.
The folding and unfolding of the ex-
terior mirrors can be deactivated by
a PEUGEOT dealer.
To locate your vehicle, if
you have locked it, in a
car park:
press button B , the courtesy lights
come on and the direction indica-
t o r s l a s h f o r a f e w s e c o n d s .
Changing the remote control
battery
Reprogramming the remote
control
Following disconnection of the vehi-
cle’s battery, replacement of the remote
Page 76 of 212
ACCESS
69
To switch on
Press and hold button A .
Activation of the function is accom-
panied by a message on the multi-
function display.
Automatic central locking of the
doors
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h)).
Above 6 mph (10 km/h), press button
A
b r i e l y t o u n l o c k t h e d o o r s t e m p o r a r i l y .
You can activate or deactivate this
function .
To switch off
Press and hold button A .
Deactivation of the function is ac-
companied by a message on the
multifunction display. "Door open" alert
If a door has not been closed properly:
-
when the engine is running ,
you are warned by a diagram and
a message on the multifunction
display for a few seconds,
- when the vehicle is moving
(speed above 6 mph (10 km/h)),
the service warning light comes on.
This is accompanied by an audible
signal, a message and a diagram
on the multifunction display for a few
seconds.
This prevents either of the rear doors
being opened from inside.
Turn the switch on each rear door
a quarter of a turn using the igni-
tion key.
Child safety
Notes:
If one of the doors is open, locking
from the inside and automatic central
locking are not possible.
If the boot is open, automatic central
locking of the doors is active.
Page 77 of 212
ACCESS
69
To switch on
Press and hold button A .
Activation of the function is accom-
panied by a message on the multi-
function display.
Automatic central locking of the
doors
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h)).
Above 6 mph (10 km/h), press button
A
b r i e l y t o u n l o c k t h e d o o r s t e m p o r a r i l y .
You can activate or deactivate this
function .
To switch off
Press and hold button A .
Deactivation of the function is ac-
companied by a message on the
multifunction display. "Door open" alert
If a door has not been closed properly:
-
when the engine is running ,
you are warned by a diagram and
a message on the multifunction
display for a few seconds,
- when the vehicle is moving
(speed above 6 mph (10 km/h)),
the service warning light comes on.
This is accompanied by an audible
signal, a message and a diagram
on the multifunction display for a few
seconds.
This prevents either of the rear doors
being opened from inside.
Turn the switch on each rear door
a quarter of a turn using the igni-
tion key.
Child safety
Notes:
If one of the doors is open, locking
from the inside and automatic central
locking are not possible.
If the boot is open, automatic central
locking of the doors is active.
Page 82 of 212
VISIBILITY
74
A u t o m a t i c s w i t c h i n g o n o f t h e
lights
Side lights and dipped beam
headlamps switch on automatically if
the light is poor, or during operation of
the windscreen wipers. They switch
off as soon as the light becomes
bright enough or the windscreen
wipers stop.
Note: in foggy weather or in snow,
the brightness sensor can detect
s u f i c i e n t l i g h t . A s a c o n s e q u e n c e , t h e
lights will not come on automatically.
Deactivation
Turn ring A to a position other
than "AUTO" . Switching off is
accompanied by a message on
the multifunction display.
I f t h e b r i g h t n e s s s e n s o r d o e s n o t
f u n c t i o n c o r r e c t l y , the lights come
on accompanied by the service
warning light, an audible signal and
a message on the multifunction
display.
Contact a PEUGEOT dealer.
M a n u a l " F o l l o w - m e - h o m e "
lighting
W h e n t h e a u t o m a t i c s w i t c h i n g o n
o f t h e l i g h t s f u n c t i o n i s d e a c t i v a t e d ,
the side lights and dipped headlamps
remain on for the duration selected
for the automatic "follow-me-home"
lighting.
I f t h e v e h i c l e i s n o t i t t e d w i t h t h e
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
f u n c t i o n , when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
D i r e c t i o n i n d i c a t o r s ( l a s h e r s )
L e f t : downwards.
Right: upwards.
Note: if you forget to cancel the
direction indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
A u t o m a t i c " F o l l o w m e h o m e "
lighting
With the ignition off, when you leave
your vehicle with the automatic
s w i t c h i n g o n o f t h e l i g h t s f u n c t i o n
activated , the side lights and dipped
headlamps remain on for the selected
duration. Activation:
switch off the engine,
" l a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
" l a s h " t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
To deactivate or activate this
function, go to the multifunction
d i s p l a y c o n i g u r a t i o n m e n u .
The duration of the timed
period must also be set (15,
30, 60 seconds), via the multifunction
d i s p l a y c o n i g u r a t i o n m e n u , e x c e p t i n
the case of the monochrome screen
A for which it is pre-set.
C a n c e l l i n g :
" l a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it. Activation
Turn ring A to the "AUTO"
position. The automatic lighting
is accompanied by a message on
the multifunction display.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen, behind
the interior mirror. It is used for the
automatic switching on of the lights.
Page 83 of 212
VISIBILITY
74
A u t o m a t i c s w i t c h i n g o n o f t h e
lights
Side lights and dipped beam
headlamps switch on automatically if
the light is poor, or during operation of
the windscreen wipers. They switch
off as soon as the light becomes
bright enough or the windscreen
wipers stop.
Note: in foggy weather or in snow,
the brightness sensor can detect
s u f i c i e n t l i g h t . A s a c o n s e q u e n c e , t h e
lights will not come on automatically.
Deactivation
Turn ring A to a position other
than "AUTO" . Switching off is
accompanied by a message on
the multifunction display.
I f t h e b r i g h t n e s s s e n s o r d o e s n o t
f u n c t i o n c o r r e c t l y , the lights come
on accompanied by the service
warning light, an audible signal and
a message on the multifunction
display.
Contact a PEUGEOT dealer.
M a n u a l " F o l l o w - m e - h o m e "
lighting
W h e n t h e a u t o m a t i c s w i t c h i n g o n
o f t h e l i g h t s f u n c t i o n i s d e a c t i v a t e d ,
the side lights and dipped headlamps
remain on for the duration selected
for the automatic "follow-me-home"
lighting.
I f t h e v e h i c l e i s n o t i t t e d w i t h t h e
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
f u n c t i o n , when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
D i r e c t i o n i n d i c a t o r s ( l a s h e r s )
L e f t : downwards.
Right: upwards.
Note: if you forget to cancel the
direction indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
A u t o m a t i c " F o l l o w m e h o m e "
lighting
With the ignition off, when you leave
your vehicle with the automatic
s w i t c h i n g o n o f t h e l i g h t s f u n c t i o n
activated , the side lights and dipped
headlamps remain on for the selected
duration. Activation:
switch off the engine,
" l a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
" l a s h " t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
To deactivate or activate this
function, go to the multifunction
d i s p l a y c o n i g u r a t i o n m e n u .
The duration of the timed
period must also be set (15,
30, 60 seconds), via the multifunction
d i s p l a y c o n i g u r a t i o n m e n u , e x c e p t i n
the case of the monochrome screen
A for which it is pre-set.
C a n c e l l i n g :
" l a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it. Activation
Turn ring A to the "AUTO"
position. The automatic lighting
is accompanied by a message on
the multifunction display.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen, behind
the interior mirror. It is used for the
automatic switching on of the lights.
Page 110 of 212
DRIVING
98
HANDBRAKE
Applying
Pull the handbrake to immobilise
your vehicle. When the vehicle is being
driven, illumination of
this warning light and
of the STOP warning
light, accompanied by an
audible signal and a message on the
multifunction etdisplay, indicates that
the handbrake is still on or has not
been properly released.
When parking on a slope,
direct your wheels towards
the pavement and pull the
handbrake.
Releasing
Pull on the handle and press the
button to release the handbrake.
The four or six speed automatic
gearbox offers a choice between
the comfort of integral automatic
operation , enhanced by a sport and
a snow programme, or manual gear
changing .
P ark: to immobilise the vehicle or
start the engine , with the handbrake
on or off.
R everse: to reverse (select this
position with the vehicle stationary,
engine at idle).
N eutral: to start the engine and to
park , with the handbrake on.
Note: if position N is engaged
inadvertently while driving, allow
the engine to return to idle before
engaging position D to accelerate.
D rive: for driving in automatic
mode.
M anual: to select the gears.
S : sport programme.
: snow programme.
Gear selection gate
Move the lever in the gate to
select a position.
The indicator light for the selection is displayed on the instrument
panel display.
Starting the engine
with the handbrake applied,
select position P or N in the gate,
turn the ignition key to the
Starting position.
Otherwise, you are warned by an
audible signal and a message on the
multifunction display.
"PORSCHE TIPTRONIC
SYSTEM" AUTOMATIC
GEARBOX
Page 111 of 212
DRIVING
98
HANDBRAKE
Applying
Pull the handbrake to immobilise
your vehicle. When the vehicle is being
driven, illumination of
this warning light and
of the STOP warning
light, accompanied by an
audible signal and a message on the
multifunction etdisplay, indicates that
the handbrake is still on or has not
been properly released.
When parking on a slope,
direct your wheels towards
the pavement and pull the
handbrake.
Releasing
Pull on the handle and press the
button to release the handbrake.
The four or six speed automatic
gearbox offers a choice between
the comfort of integral automatic
operation , enhanced by a sport and
a snow programme, or manual gear
changing .
P ark: to immobilise the vehicle or
start the engine , with the handbrake
on or off.
R everse: to reverse (select this
position with the vehicle stationary,
engine at idle).
N eutral: to start the engine and to
park , with the handbrake on.
Note: if position N is engaged
inadvertently while driving, allow
the engine to return to idle before
engaging position D to accelerate.
D rive: for driving in automatic
mode.
M anual: to select the gears.
S : sport programme.
: snow programme.
Gear selection gate
Move the lever in the gate to
select a position.
The indicator light for the selection is displayed on the instrument
panel display.
Starting the engine
with the handbrake applied,
select position P or N in the gate,
turn the ignition key to the
Starting position.
Otherwise, you are warned by an
audible signal and a message on the
multifunction display.
"PORSCHE TIPTRONIC
SYSTEM" AUTOMATIC
GEARBOX