ABS Peugeot 307 Break 2002.5 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2002.5, Model line: 307 Break, Model: Peugeot 307 Break 2002.5Pages: 185, PDF Size: 2.54 MB
Page 21 of 185
09-09-2002
PEUGEOT SERVICING25
A AND C SERVICE LEVELS AND THE INTERMEDIATE VISIT
Level
Operations Description of operation 1st Service
A C Intermediate
DRAIN/REFILL Engine oil Bleed fuel filter (diesel) Oil filter Fuel filter *(petrol) REPLACE Fuel filter element (diesel) Air filter element Spark plugs (petrol) Engine oil (check + top up) Manual gearbox oil (check + top up) Battery (check + top up) if cap is removable Level Screen wash (check + top up) Coolant (check + top up) Brake fluid (check + top up) Power steering fluid (check + top up according to specification) Operation of lights and indicators Condition of glass, headlamp and light lenses and mirrors Horn Windscreen washer jets Condition of wiper blades Condition and tension of the ancillary drive belts Handbrake Condition of hydraulic circuits (hoses and covers) CHECK Condition of rubber boots and gaiters Brake pads Play in hubs, link rods, ball joints, flexible mountings Shock absorbers Rear drum brake lining wear. Condition and pressure of tyres (including spare wheel) Emission control check as per current legislation (petrol) Smoke opacity (diesel) Pollen filter (according to specification) Visual check of the whole vehicle
SERVICE* Courtesy vehicle
ROAD TEST
: All driving conditions : Arduous conditions * According to country.
Page 23 of 185
09-09-2002
RECOMMENDATIONS FOR
APPROVED LUBRICANTS
The oils which appear in the table
opposite are suitable for most pur
poses.
The diagram opposite states the
optimum range of viscosity depend
ing on the temperatures at which the
oils are to be used.
It is also possible to use "superior
quality" synthetic oils.
In the absence of semi synthetic or
synthetic oils, oils of API SH/SJ qual
ity (for petrol engines), or CD/CF
quality (for diesel engines) may be
used by following the "Arduous
Conditions" servicing schedule,
which specifies shorter intervals.
Do not hesitate to ask for advice from
a PEUGEOT dealer to maintain dri
ving pleasure and to minimise the
maintenance cost of your vehicle.
For countries outside Europe, please
contact a local PEUGEOT dealer.
PEUGEOT SERVICING27
Manual
ONLY ONLY
Gearbox ESSO Gear Oil BV TOTAL TRANSMISSION BV 75W 80 PR 9736.41 75W 80
AutomaticONLY
GearboxATF 4HP20 AL4PR 9736.22
Other approved products
Power steering FLUIDE DA PR 9730. A1
Brake fluid PEUGEOT DOT4
Coolant
ONLY PROCOR TM108/GLYSANTIN G33 or REVKOGEL 2000
Protection to minus 35C
Page 24 of 185
09-09-2002
1 Rev counter.
2 Seat belt not fastened warning
light.
3 Engine diagnostics warning
light.
4 Handbrake and low brake fluid
level warning light.
5 Left hand direction indicator.
6 Coolant temperature indicator. 7
Battery charge warning light.
8 Central (STOP) warning light.
9 Engine oil pressure warning
light.
10 Low fuel level warning light.
11 Right hand direction indicator.
12 Fuel gauge.
13 ABS warning light. 14
Air bag warning light.indicator
light.
16 Speedometer.
17 Service indicator, oil level and
total distance recorder.
18 Trip recorder zero reset.
19 Rear fog lamp indicator light.
20 ESP/ASR warning light
21 Front fog lamps indicator
light.
22 Diesel engine preheating light.
23 Main beam headlamps
indicator light.
24 Low coolant level warning light.
25 Dipped beam headlamps
indicator light.
26 Water in diesel filter warning
light.
27 Lighting rheostat.
INSTRUMENTS AND CONTROLS
28
PETROL / DIESEL INSTRUMENT PANEL DIALS: MANUAL GEARBOX
Page 25 of 185
09-09-2002
INSTRUMENTS AND CONTROLS29
1
Rev counter.
2 Seat belt not fastened warning
light.
3 Engine diagnostics warning
light.
4 Handbrake and low brake fluid
level warning light.
5 Left hand direction indicator.
6 Coolant temperature indicator. 7
Battery charge warning light.
8 Central (STOP) warning light.
9 Engine oil pressure warning
light.
10 Low fuel level warning light.
11 Right hand direction indicator.
12 Fuel gauge.
13 ABS warning light. 14
Air bag warning light.
15 Passenger air bag disarming
indicator light.
16 Speedometer.
17 Service indicator, oil level and
total distance recorder.
18 Trip recorder zero reset.
19 Rear fog lamp indicator
light.
20 ESP/ASR warning light
21 Front fog lamps indicator light.
22 Main beam headlamps indicator
light.
23 Low coolant level warning light.
24 Dipped beam headlamps
indicator light.
25 Lighting rheostat.
26 Sport programme indicator light.
27 Snow programme indicator
light.
28 Gear lever position indicator.
PETROL INSTRUMENT PANEL DIALS: AUTOMATIC GEARBOX
Page 26 of 185
Low coolant level warning light
Linked to the central STOPwarning light.
This comes on for approximately 3 seconds each time the ignition is switched on.
This warning light is accompanied by an audible signal and the message "Top up
coolant " on the multi function display.
Stop immediately. Central STOP warning light
This light comes on each time the ignition is switched on.
It is linked to the "engine oil pressure", ''oil temperature''
, ''coolant
level low'', ''brake fluid level'', "electronic brake force dist ribution
fault' and ''coolant temperature gauge'' warning lights.
The STOP warning light flashes if one of the doors or the boot is o pen. A diagram appears
on the multi function display for a few seconds, accompanied by an audible signal.
In this case, it is not essential to stop if this is a delib erate action on the part of
the driver (e.g. transportation of long objects).
Stop immediately if it comes on permanently with the engine running.
Contact a PEUGEOT dealer.
Engine oil pressure warning light
Linked to the central STOPwarning light.
If it comes on with the engine running, it is accompanied b y an audible
signal and the message ''Oil pressure low''or ''Top up engine oil'' on
the multi function display.
Stop immediately.
If there is a lack of oil in the lubrication circuit, top up the level.
Contact a PEUGEOT dealer without delay.
INSTRUMENTS AND CONTROLS
A permanently lit warning light or one that flashes with the engine running,
indicates an operating fault in the relevant unit. Some war ning lights may
be linked to buzzers and a message on the multi function di splay. Do not
ignore this warning: contact a PEUGEOT dealer as soon as p ossible.
If the Central STOP warning light comes on when you are d riving, stop
immediately where it is safe to do so. Warning:
Allow the engine to cool
before topping up.
The cooling system is pressurised.
To prevent the risk of scalding,
unscrew the cap by two turns to
allow the pressure to drop.
Once the pressure has dropped,
remove the cap and top up the level.
Contact a PEUGEOT dealer.
Handbrake and low brake
fluid level warning light
Linked to the central STOP
warning light.
This comes on each time the ignition is
switched on.
Illumination of this light is accompa
nied by an audible signal and a
message on the multi function display
indicating the cause of the warning: ''Handbrake on'', if the handbrake
is applied or has not been released
correctly,
''Low brake fluid level'' if there is
an excessive drop in the brake fluid
(if the light remains on even with the
handbrake released),
''Brake system problem'' is dis
played simultaneously with the ABS
light, indicating a malfunction of the
electronic brake force distribution.
Stop immediately.
Contact a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS
30
09-09-2002
Page 27 of 185
09-09-2002
Battery charge
warning light
This comes on each time
the ignition is switched on.
If it comes on with the engine run
ning, it is accompanied by an audible
signal and a message "Low battery
charge" on the multi function
display.
It can indicate:
faulty operation of the charging circuit,
loose battery or starter terminals,
a cut or slack alternator belt,
an alternator fault.
Contact a PEUGEOT dealer.
ABS warning light
This light comes on for
3 seconds each time the
ignition is switched on.
If it remains on or comes on above
8mph (12 kmh), this indicates a mal
function of the ABS.
However, the vehicle retains conven
tional servo assisted braking.
Illumination of this light is accompa
nied by an audible signal and the
message ''ABS system problem''
on the multi function display.
Contact a PEUGEOT dealer. Electronic stability programme (ESP/ASR) warning light
This comes on for 3 seconds each time the ignition is switched o
n.
If the light remains on or comes on when the engine is runni ng and the
vehicle is moving, it is accompanied by an audible signal and the mes
sage ''ESP/ASR system not operational'' on the multi function display; contact
a PEUGEOT dealer.
Diesel pre heat light
This comes on each time the ignition is switched on
Wait until it goes out before trying the starter.
Water in diesel filter warning light
(according to country)
Illumination on of this warning light is accompanied by an audible signal
and the message ''Water in diesel filter'' on the multi function display.
There is a risk of damage to the injection system.
Contact a PEUGEOT dealer a soon as possible. .
Engine diagnostics warning light
This comes on each time the ignition is switched on.
The warning light showing clogging of the particulate emi
ssion filter is
linked to the engine diagnostics warning light.
If it comes on with the engine running, accompanied by an a udible signal and the
message ''Emission control system problem'' on the multi function display, it
indicates a malfunction in the emission control system. ''Diesel additive low level'' or "Risk of clogging of particulate emission
filter" indicates a malfunction in the particulate emission filter.
If it flashes when the engine is running, accompanied by an audible signal and
the message ''Catalytic converter faulty'' on the multi function display, it indi
cates a malfunction in the injection or ignition system. There is a risk of damage
to the catalytic converter (petrol engines only).
Contact a PEUGEOT dealer as soon as possible.
INSTRUMENTS AND CONTROLS 31
Page 55 of 185
09-09-2002
YOUR 307 IN DETAIL
54
GENERAL FUNCTIONS On/off
With the ignition switch in the accessories position or with the ignition on, press button Cto switch the audio
function of the RT3 audio/telephone on or off.
Note: in the absence of an ignition key, press button Cto switch the telematics system on or off.
The RT3 telephone can operate for 30 minutes without switc hing the vehicle ignition on.
Notes:
the SIM card must be removed only after the audio/telephone h as been switched off,
following automatic switching off of the audio/telepho ne after 30 minutes it is possible to make a telephone call by press
ing button D,
after the ignition has been switched off, the audio/te lephone can be switched on again by pressing buttons D, E , V or by
inserting a CD in the player.
Anti theft system
The RT3 audio/telephone is coded in such a way that it ca n operate only on your vehicle. If fitting it to another vehicle, con
sult your PEUGEOT dealer for configuration of the system.
The system is automatic and requires no action on your part.
ADJUSTING THE VOLUME
Turn button Cclockwise to increase the volume of the audio/telephone or an ti clockwise to decrease it.
Note: the volume setting is specific to each source. It is possible to have different settings for radio, CD or CD changer.
AUDIO SETTINGS Press buttonUto access Bass,Treble , Loudness , Fader (front/rear balance), Balance (left/right balance)
and Automatic volume adjustment settings.
Exit from audio mode is automatic after a few seconds without a ny action, or by pressing button J.
Note: bass and treble settings are specific to each source. It is possibl e to have different settings for radio,
CD or CD changer.
Page 69 of 185
09-09-2002
YOUR 307 IN DETAIL
68
Services* Press button Eto display the "Services"menu and select one of the following services:
• "Customer Contact Centre" which enables you to contact the PEUGEOT Customer Contact Centre directly
and access the services offered (this type of call is suspended if a n emergency or breakown call is made).
• "Peugeot Assistance" which enables you to contact the call centre which controls the PEUGEOT breakdown ser
vice directly and receive rapid assistance (you have 6 seconds within which to cancel the call when it is made).
During the breakdown call phase it is not possible to make an y other calls with the exception of emergency calls.
• "Operator services" which gives access to the list of services specific to the operator (e .g.: customer service, consump
tion monitoring, news, stock market, weather, travel, games, etc) if they are available.
Note: during connection to a service, it is not possible to receive cal ls or SMS mini messages, they will be diverted to your
voice message service. Contrarily, it is possible to send a call wh ich results in automatic disconnection.
Emergency call*
In an emergency, press button Vuntil a signal is heard and a call validation / deletion screen is displayed (delay of
6 seconds) or enter 11 2directly.
Note: in this case, a green diode flashes on the RT3 audio/tele phone panel when the emergency call procedure begins then
lights permanently when the call is taken by the emergency services.
In the absence of a specific service contract, the parameters of th e SOS button are set so that a call is made to 11 2 unique
number made available by the worldwide GSM network, reserved for e mergency calls.
Before making a call of this kind, the audio/telephone must detect a cellular network. No security mode is required and,
depending on the network, you do not need to insert your SI M card or enter your PIN.
If you have signed the specific contract, refer to its general co nditions.
* If option and service available.
Page 70 of 185
YOUR 307 IN DETAIL69
Voice commands
The voice commands make it possible to use pre recorded words or phrases to control a certain number of functions of the
RT3 audio/telephone.
Activation of the voice commands
Press the button on the end of the lights stalk to activate this function.
Example: to recall the radio station stored on button 3, the key words are: "Radio" "Memory" "3" .
To use these key words, you must say the word "Radio", wait for the audible confirmation signal, then say the w ord
"Memory" , wait for the audible confirmation signal, then end wit h the word"3", wait for the audible confirmaton signal which
will carry out the action requested.
Notes:
in the absence of any voice commands, this function will be sw itched off after approximately ten seconds,
if a command is not understood, a double audible signal i s emitted.
Saying the word "Help"displays all of the commands available on the screen.
List of
commands available
To change the source (Radio, CD, CD changer, telephone) : "RADIO" / "CD" / "CHANGER" / "CALL"
For the radio: "LISTEN" / "PREVIOUS" / "FOLLOWING" / "MEMORY" + N° / "AUTOSTORE"
For the CD: "LISTEN" / "PLAY" / " PREVIOUS TRACK" / "FOLLOWING TRACK" / "TRACK NUMBER" + N° / "SHUFFLE" / "SCAN" /
"LOOP"
for the CD changer: "LISTEN"/ "PLAY" / " PREVIOUS TRACK" / "FOLLOWING TRACK" / "TRACK NUMBER" + N° / "PREVIOUS DISC" / "FOL
LOWING DISC" / "DISC NUMBER" + N° / "SHUFFLE" / "SCAN" / "LOOP"
For the telephone: "CALL" / "REPEAT" / " PEUGEOT SERVICE"
For the navigation/card: "STOP GUIDANCE" / "RE START GUIDANCE" / "REDUCE ZOOM " / "INCREASE ZOOM "
Various: "CANCEL" / "HELP"
09-09-2002
Page 80 of 185
09-09-2002
YOUR 307 IN DETAIL79
The menu ''Guidance options'' pro
vides access to the following func
tions:
changing of the route calculation criteria,
voice synthesis adjustment of guid ance messages,
description of the information relat ing to the navigation CD Rom,
management of the addresses stored in the directory.
Guidance options
The last criteria used are displayed.
Select a criterion from the list, then
validate by pressing the dial.
When the criterion of your choice has
been selected, select the
"OK"func
tion then confirm by pressing the
dial.
Adjusting the voice synthesiser
Select the type of voice "male"or
"female" , after inserting the configu
ration CD ROM.
Adjust the volume of the voice syn
thesis by turning the dial, then vali
date by pressing the dial.
Note: the volume can also be adjust
ed during a message, using the
audio/telephone button on the steer
ing wheel control. Management of the directory
This function enables you to rename
or delete an address stored in the
directory.
Select the description corresponding
to the stored address to be changed.
Select the
"Delete" function or the
"Rename" function, then confirm by
pressing the dial.
Select the "OK" function, then con
firm by pressing the dial to record the
changes made.
Stopping / Resuming guidance
"Stop guidance"
During guidance, select this function
then validate.
"Resume guidance"
In the absence of guidance select
this function then validate to activate
guidance to the last destination pro
grammed.
Calculation criteria