spare PEUGEOT 308 2010 Owners Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 308, Model: PEUGEOT 308 2010Pages: 315, PDF Size: 23.05 MB
Page 15 of 315
18
ARRANGE YOUR BOOT
3 position adjustable boot
Low position (150 kg max). 108
T o r e l e a s e t h e fl o o r , p u s h
slightly forwards then
raise.
Use the stops A , placed on each
side of the boot to change the
h e i g h t o f t h e fl o o r m o r e e a s i l y . Intermediate position (100 kg max). High position (50 kg max) w
ith the lower
tailgate closed to isolate the lower part
of the boot.
F r o m t h e h i g h p o s i t i o n , p l a c e t h e fl o o r
in this position (at an angle), two stops
support it to allow access underneath it
or to the spare wheel.
Page 119 of 315
FITTINGS
When changing a wheel
The hooks permit easy access
to the spare wheel by retain-
ing the boot carpet by means of the
two cords.
The hooks permit the securing of
shopping bags.
Hooks
In order to connect a 12 V accessory
(max power: 120 Watts), remove
the cap and connect the appropriate
adaptor.
Turn the key to the ignition position.
12 V accessories socket Luggage retaining net
Hooked onto the stowing rings on the
m o v a b l e b o o t fl o o r , t h i s e n a b l e s y o u t o
secure your luggage.
Observe the loads indicated on the side
of the boot, in accordance with the posi-
t i o n o f t h e m o v a b l e fl o o r .
For safety reasons in case of sharp
braking, we recommend that heavy ob-
j e c t s a r e p l a c e d o n t h e fl o o r a s c l o s e a s
possible to the back of the rear seats.
Page 120 of 315
FITTINGS
107
Raise the boot carpet, hooking the
two cords on the hooks, then gain
access to the storage box.
D e p e n d i n g o n t h e c o n fi g u r a t i o n , t h i s
has areas for storing:
- a box of spare bulbs,
- a fi r s t a i d k i t ,
- a tyre repair kit,
- two warning triangles,
- ... Storage box CD changer
This holds up to 6 discs.
Access
- P l a c e t h e fl o o r i n t h e l o w p o s i t i o n .
- R e m o v e t h e fl a p b y t u r n i n g i t s b u t t o n .
- Pivot the changer towards you then change the discs, one by one.
- Put the changer back in its location.
- C l o s e t h e fl a p c o r r e c t l y t o p r e v e n t the changer from coming out of its
location while driving. The use of copied compact
discs may cause faults.
Insert circular compact discs only.
Page 124 of 315
FITTINGS
When changing a wheel
The hooks permit easy access
to the spare wheel by retain-
ing the boot carpet by means of the
two cords.
The hooks permit the securing of
shopping bags.
Hooks
In order to connect a 12 V accessory
(max power: 120 Watts), remove
the cap and connect the appropriate
adaptor.
Turn the key to the ignition position.
12 V accessories socket Luggage retaining net
Hooked onto the stowing rings on the
m o v a b l e b o o t fl o o r , t h i s e n a b l e s y o u t o
secure your luggage.
Observe the loads indicated on the side
of the boot, in accordance with the posi-
t i o n o f t h e m o v a b l e fl o o r .
For safety reasons in case of sharp
braking, we recommend that heavy ob-
j e c t s a r e p l a c e d o n t h e fl o o r a s c l o s e a s
possible to the back of the rear seats.
Page 125 of 315
FITTINGS
107
Raise the boot carpet, hooking the
two cords on the hooks, then gain
access to the storage box.
D e p e n d i n g o n t h e c o n fi g u r a t i o n , t h i s
has areas for storing:
- a box of spare bulbs,
- a fi r s t a i d k i t ,
- a tyre repair kit,
- two warning triangles,
- ... Storage box CD changer
This holds up to 6 discs.
Access
- P l a c e t h e fl o o r i n t h e l o w p o s i t i o n .
- R e m o v e t h e fl a p b y t u r n i n g i t s b u t t o n .
- Pivot the changer towards you then change the discs, one by one.
- Put the changer back in its location.
- C l o s e t h e fl a p c o r r e c t l y t o p r e v e n t the changer from coming out of its
location while driving. The use of copied compact
discs may cause faults.
Insert circular compact discs only.
Page 138 of 315
119
TYRE UNDER-INFLATION DETECTION
System which automatically checks the
pressure of the tyres while driving. All repairs and changing of
t y r e s o n a w h e e l fi t t e d w i t h t h i s
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install
a wheel which is not detected by
y o u r v e h i c l e ( e x a m p l e : fi t t i n g o f s n o w
tyres), you must have the system re-
initialised by a PEUGEOT dealer.
This system does not eliminate
the need to have the tyre pres-
sure checked regularly (refer
t o t h e " I d e n t i fi c a t i o n m a r k i n g s " p a r a -
graph) to ensure that the optimum
dynamic performance of the vehicle
is maintained and prevent premature
wear of the tyres, particularly in ardu-
ous driving conditions (heavy load,
high speed).
The tyre pressures must be checked
cold, at least once a month. Re-
member to check the pressure of the
spare wheel.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n
system may experience temporary
interference due to radioelectric
emissions on a frequency close to
that used by the system.
S e n s o r s fi t t e d i n e a c h v a l v e t r i g g e r a
warning in the event of malfunction
(speed above 12 mph (20 km/h)).
T h e s p a r e w h e e l i s n o t fi t t e d w i t h a s e n s o r .
This warning lamp is displayed
on the instrument panel and/or
a message appears on the mul-
tifunction screen, accompanied
by an audible signal, to locate
the wheel concerned.
Check the tyre pressures as soon
as possible.
This check must be carried out when the
tyres are cold.
Flat tyre The
STOP warning lamp
comes on, accompanied by
an audible signal and a mes-
sage on the multifunction
screen locating the wheel
concerned.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
t u r e d o r v e r y d e fl a t e d t y r e ) , a n d
have the tyre pressure checked as
soon as possible.
Puncture
T h e t y r e u n d e r - i n fl a t i o n d e t e c -
tion system is an aid to driv-
ing which does not replace the
need for the driver to be vigilant or to
drive responsibly. Sensor(s) not detected or faulty
A message appears on the multifunc-
tion screen, accompanied by an audible
signal, to locate the wheel or wheels
which are not detected or to indicate a
fault in the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
This message is also dis-
played when one of the wheels
is away from the vehicle (be-
ing repaired) or when one or more
w h e e l s w i t h o u t a s e n s o r a r e fi t t e d .
Page 164 of 315
140
In certain extreme weather
conditions (rain and/or snow,
bright sunshine, ...) the head-
up display may not be legible or may
suffer temporary interference.
Certain glasses (sunglasses, specta-
cles or polarised lenses) may hamper
reading of the information.
To clean the transparent strip, which
is made of organic glass, use a clean,
soft cloth (such as a spectacles cloth
o r m i c r o fi b r e c l o t h ) . D o n o t u s e a d r y
or abrasive cloth or detergent or sol-
vent products as these could scratch
t h e s t r i p o r d a m a g e t h e a n t i - r e fl e c -
tion coating. We recommend that adjust-
ments are only made using
these buttons when the vehi-
cle is stationary.
When stationary or while driving, no
objects should be placed around the
transparent strip (or on its cover) to
avoid blocking the strip output and
preventing its correct operation.
With the engine running, press button 1 .
The activated/deactivated status when
the engine was switched off is retained
when the engine is switched on again.
Height adjustment
With the engine running, adjust the
display to the required height using
button 3 :
- up to move the display up,
- down to move the display down.
Activation/Deactivation Brightness adjustment
With the engine running, adjust the
brightness of the information using
button 2 :
- up to increase the brightness,
- down to decrease the brightness.
Page 182 of 315
CHECKS
159
RUNNING OUT OF FUEL (DIESEL)
I f y o u r v e h i c l e i s fi t t e d w i t h a n H D I e n -
gine, the fuel system must be primed if
you run out of fuel.
This system consists of a priming pump
and, according to engine (see graphic
and explanations below), a transparent
pipe and a bleed screw under the bonnet
(refer to the corresponding graphic). 1.6 litre Turbo HDI 16V engine
F i l l t h e f u e l t a n k w i t h a t l e a s t fi v e l i t r e s
of diesel.
Open the bonnet.
Operate the priming pump until it
hardens.
Operate the starter until the engine
starts.
Close the bonnet. 2 litre Turbo HDI 16V engine
F i l l t h e f u e l t a n k w i t h a t l e a s t fi v e l i -
tres of diesel.
Open the bonnet.
Unclip the style cover for access to
the priming pump.
Slacken the bleed screw.
Squeeze and release the priming
pump until fuel appears in the trans-
parent pipe with the green connector.
Retighten the bleed screw.
Operate the starter until the engine
starts.
Put the style cover back in position
and clip it in place.
Close the bonnet.
If the engine does not start
a t t h e fi r s t a t t e m p t , d o n o t t r y
again.
Operate the priming pump again,
then the starter. If the engine does not start
a t t h e fi r s t a t t e m p t , d o n o t t r y
again.
Operate the priming pump again,
then the starter.
Page 196 of 315
PRACTICAL INFORMATION
Access to the spare wheel
The spare wheel is installed in the boot
u n d e r t h e fl o o r .
A c c o r d i n g t o c o u n t r y , t h e s p a r e w h e e l
m a y b e s t e e l , a l l o y o r o f t h e " s p a c e -
s a v e r " t y p e .
T o g a i n a c c e s s t o i t , r e f e r t o t h e p a r a -
g r a p h " A c c e s s t o t h e t o o l s " o n t h e p r e v i -
o u s p a g e . Taking out the wheel
U n s c r e w t h e y e l l o w c e n t r a l b o l t .
Raise the spare wheel towards you
f r o m t h e r e a r .
T a k e t h e w h e e l o u t o f t h e b o o t .
Putting the wheel back in place
P u t t h e w h e e l b a c k i n i t s h o u s i n g .
Unscrew the yellow central bolt by a
few turns then put it in place in the
c e n t r e o f t h e w h e e l .
Tighten fully until the central bolt
c l i c k s t o r e t a i n t h e w h e e l c o r r e c t l y .
P u t t h e b o x b a c k i n p l a c e i n t h e c e n -
t r e o f t h e w h e e l a n d c l i p i t .
P u t t h e p o l y s t y r e n e s t o r a g e b o x
b a c k i n p l a c e .
T y r e u n d e r - i n fl a t i o n d e t e c t i o n
T h e s p a r e w h e e l i s n o t fi t -
t e d w i t h a s e n s o r . T h e p u n c -
tured wheel must be repaired by a
P E U G E O T d e a l e r .
Page 197 of 315
PRACTICAL INFORMATION
172
Parking the vehicle
I m m o b i l i s e t h e v e h i c l e w h e r e
i t d o e s n o t b l o c k t r a f fi c : t h e
g r o u n d m u s t b e l e v e l , s t a b l e a n d
n o n - s l i p p e r y g r o u n d .
Apply the parking brake unless it
has been programmed to automatic
m o d e , s w i t c h o f f t h e i g n i t i o n a n d e n -
g a g e fi r s t g e a r * t o l o c k t h e w h e e l s .
Check that the braking warning lamp
and the P w a r n i n g l a m p o n t h e p a r k -
i n g b r a k e c o n t r o l c o m e o n .
I f n e c e s s a r y , p l a c e a c h o c k u n d e r t h e
wheel diagonally opposite the wheel
t o b e c h a n g e d .
T h e o c c u p a n t s m u s t g e t o u t o f t h e v e -
h i c l e a n d w a i t w h e r e t h e y a r e s a f e .
Never go underneath a vehicle raised
u s i n g a j a c k ; u s e a n a x l e s t a n d .
Removing a wheel
List of operations
Remove the chromed bolt cover
from each of the bolts using the
tool 3 ( a c c o r d i n g t o e q u i p m e n t ) .
F i t t h e s e c u r i t y s o c k e t 5 on the
wheelbrace 1 to slacken the security
b o l t .
Slacken the other bolts using the
wheelbrace 1 o n l y .
Place the jack 2 in contact with one
of the two front A or rear B locations
p r o v i d e d o n t h e u n d e r b o d y , w h i c h -
ever is closest to the wheel to be
c h a n g e d .
E x t e n d t h e j a c k 2 until its base plate
i s i n c o n t a c t w i t h t h e g r o u n d . E n s u r e
that the centreline of the jack base
plate is directly below the location A
or B u s e d .
R a i s e t h e v e h i c l e u n t i l t h e r e i s s u f -
fi c i e n t s p a c e b e t w e e n t h e w h e e l a n d
the ground to admit the spare (not
p u n c t u r e d ) w h e e l e a s i l y .
Remove the bolts and store them in
a c l e a n p l a c e .
R e m o v e t h e w h e e l .
* p o s i t i o n R for the electronic gear
c o n t r o l m a n u a l g e a r b o x ; P for the
a u t o m a t i c g e a r b o x .