reverse Peugeot 308 2016 Owner's Guide

206
308_en_Chap06_conduite_ed02-2015
F Once you have identified a
parking zone, press this control
at the steering wheel,
Assistance with bay parking
manoeuvres
F Select " P ark Assist" in the
" Driving assistance " menu of
the touch screen to activate the
function. F
Op

erate the direction indicator on the
parking side chosen to activate the
measurement function. You should drive
at a distance of between 0.5 m and 1.5 m
from the row of parked vehicles.
F
Dr
ive slowly following the instructions until
the system finds a free space. F
Mov

e for wards slowly until a message is
displayed, accompanied by an audible
signal, asking you to engage reverse gear.
or
F
Li
mit the speed of the vehicle to
a maximum of 12 mph (20 km/h)
and select " Star t parking in a
bay " on the touch screen. When several successive bays are
found, the vehicle will be directed
towards the last one.
Driving

207
308_en_Chap06_conduite_ed02-2015
F Select reverse, release the steering wheel
and start moving without exceeding 5 mph
(8 km/h).
F


t
he a
ssisted parking manoeuvre is in
progress.
Wi

thout exceeding 5 mph (8 km/h), follow
the instructions displayed in the instrument
panel, aided by the warnings from the
"Parking sensors" system, until the
indication of the end of the manoeuvre. At the end of the manoeuvre, the operating
indicator lamp goes off in the instrument panel,
accompanied by a message and an audible
signal.
the a

ssistance is deactivated: you can take
over control. During parking and exit from
parking manoeuvres, the reversing
camera function may come into
operation. It facilitates monitoring
of the surroundings of the vehicle,
by displaying additional information
in the instrument panel (see the
corresponding section). During a bay parking manoeuvre, the
Park Assist system is automatically
deactivated once the rear of the vehicle
is within 50 cm of an obstacle.
6
Driving

258
308_en_Chap08_en-cas-de-panne_ed02-2015
Main beam headlamps
(halogen model)
F Remove the protective plastic cover by
p
ulling on the tab.
F


t
ur
n the connector (with its bulb) towards
the top (1/4 turn).
F
Re

move the bulb by pulling it out and
change it.
For reassembly, carry out these operations in
reverse order.
Dipped beam headlamps
(halogen model)
F Remove the protective plastic cover by
p
ulling on the tab.
F
Di

sconnect the bulb connector.
F
Disenga

ge the two springs (press then
move them outwards).
F


e
xt
ract the bulb by pulling and change it.
For reassembly, carry out these operations in
reverse order.
Be aware that the area behind the
right-hand headlamp (facing forwards)
may be hot, with the risk of burns
(over flow
p

ipe).
to al

low the headlamp to be moved for ward
a few centimetres for access to the bulbs,
proceed as follows:
F Move the orange clip towards the rear
t hen while pressing on the black part
(located above the orange clip) pull on the
connector.
F
Re

move the two screws holding the lamp.
F
Disenga

ge the rear pin then the front
centre piece.
F
Mov

e the lamp for wards.
Tips for removing the headlamp (halogen model)
In the event of a breakdown

259
308_en_Chap08_en-cas-de-panne_ed02-2015
For reassembly, carry out these operations in
reverse order.
Direction indicators
(halogen model)
Faster flashing of a direction indicator
warning lamp (left or right) indicates a
failed bulb on that side.
Daytime running lamps /
sidelamps
("full LED" technology model)
For the replacement of this type of "full LeD"
l ight emitting diode lamps, contact a Peu geOt
d
ealer or a qualified workshop.
Direction indicators
("full LED" technology model)
the direction indicator bulb is located below
t he front lamp.
F


u
nc
lip the finisher by pulling at the top
(cut-out).
F


u
ns
crew the bulb holder (1/4 turn).
F
Ch

ange the failed bulb.
For reassembly, carry out these operations in
reverse order. Faster flashing of a direction indicator
warning lamp (left or right) indicates a
failed bulb on that side.
F


u
ns

crew the bulb holder (1/4 turn).
F
Re

move the bulb holder.
F
Ch

ange the failed bulb.
8
In the event of a breakdown

260
308_en_Chap08_en-cas-de-panne_ed02-2015
Integrated direction indicator
side repeaters
You should contact a Peu geOt d ealer or a
qualified workshop for the replacement of these
bulbs. You should contact a P
eu
ge
Ot d
ealer or a
qualified workshop for the replacement of the
light emitting diode - L
eD.
Front foglamps
F unclip the finisher by pulling at the top
( cut-out).
F
Re

move the two screws to remove the unit
from its housing. F Di
sconnect the connector.
F uns crew the bulb holder (1/4 turn).
F
Re

move the bulb holder.
F
Ch

ange the failed bulb.
For reassembly, carry out these operations in
reverse order, pressing on the finisher to refit it.
Door mirror spotlamps
In the event of a breakdown

261
308_en_Chap08_en-cas-de-panne_ed02-2015
1. Sidelamps (light emitting diodes - LeDs ).
2. Re versing lamps (W16W).
3.
Di

rection indicators (PY21W amber).
4.
Br

ake lamps (light emitting diodes - L
eDs
).
5.
Fo

glamps (P21W).
Rear lamps
(hatchback)
Light emitting
diodes-LEDs
For replacement, contact a Peu geOt
d ealer or qualified workshop.
Reversing lamps, direction
indicators (on the wings)
F Disconnect the lamp connector.
F Re move the lamp fixing nut.
F
Ca

refully remove the lamp unit from
outside.
F


u
ns
crew the bulb holder (a quarter of a
turn) and change the bulb.
For reassembly, carry out these operations in
reverse order.
F Op
en the tailgate then remove the access
c ove r.
8
In the event of a breakdown

262
308_en_Chap08_en-cas-de-panne_ed02-2015
F unclip the left and right access covers.
F Re move the screws located in each
opening.
F


u
nc
lip the boot trim for access to the lamp
connector.
F
Di

sconnect the lamp connector.
F
Re

move the lamp fixing nut.
F
Ca

refully remove the lamp from the
outside.
F


u
ns
crew the bulb holder (a quarter of a
turn) and change the bulb.
For reassembly, carry out these operations in
reverse order.
Foglamp (tailgate)
F Open the tailgate and then remove the
l arge plastic cover.
In the event of a breakdown

263
308_en_Chap08_en-cas-de-panne_ed02-2015
Rear lamps
(SW)
Light emitting
diodes-LEDs
For replacement, contact a Peu geOt
d ealer or qualified workshop.
Direction indicators
(on the wings)
F Open the tailgate then remove the access
c ove r.
F
Re

move the two lamp fixing nut (pipe
spanner or socket recommended).
F
Disenga

ge the retaining clip, carefully
removing the lamp unit from outside. F
Di

sconnect the lamp connector.
F
Rem
ove the sealing foam.
F

u
nc
lip the bulb holder by pressing on the
two tongues.
F
Re
place the bulb.
For reassembly, carry out these operations in
reverse order.
1.
Si

delamps (light emitting diodes - L
eDs

).
2.
Di

rection indicators (PY21W amber).
3.
Br

ake lamps (light emitting diodes - L
eDs

).
4.
Re

versing lamps (W16W).
5.
Fo

glamps (P21W).
8
In the event of a breakdown

264
308_en_Chap08_en-cas-de-panne_ed02-2015
Reversing lamp, rear foglamp
(tailgate)
F Open the tailgate and then remove the
a
ccess cover. F
Ca

refully remove the lamp from the
outside.
F
Di
sconnect the lamp connector.
F
Fo
glamp: unclip the bulb holder by
pressing on the two tongues then replace
the bulb.
F
Re
versing lamp: turn the bulb holder a
quarter of a turn then replace the bulb.
For reassembly, carry out these operations in
reverse order.
F
Re

move the lamp fixing nut.
In the event of a breakdown

273
308_en_Chap08_en-cas-de-panne_ed02-2015
Starting using another battery
First check that the slave battery has a
nominal voltage of 12 V and a capacity
at least equal to that of the discharged
battery.
Do not try to start the engine by
connecting a battery charger.
Do not disconnect the (+) terminal when
the engine is running.
F
Re

move the plastic cover from
the
(

+)
t
erminal, if your vehicle has one.
F
Co

nnect the red cable to the positive
terminal (+) of the flat battery A , then to the
positive terminal (+) of the slave battery B.
F
Co

nnect one end of the green or black
cable to the negative terminal (-) of the
slave battery B (or earth point on the other
vehicle).
F
Co

nnect the other end of the green or black
cable to the earth point C on the broken
down vehicle (or on the engine mounting).
F
St

art the engine of the vehicle with the
good battery and leave it running for a
few
m

inutes. F
Op

erate the starter on the broken down
vehicle and let the engine run
If t

he engine does not start straight
away, switch off the ignition and wait a
few
m

oments before trying again.
F
Wa

it until the engine returns to idle then
disconnect the jump lead cables in the
reverse order.
F
Re

fit the plastic cover to the (+) terminal, if
your vehicle has one.
When your vehicle's battery is discharged, the
engine can be started using a slave battery
(external or on another vehicle) and jump lead
cables.Before disconnecting the battery
Wait 2 minutes after switching off the ignition
before disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.
Following reconnection of the
battery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before starting to
permit initialisation of the electronic systems.
However, if problems remain following this
operation, contact a P
eu

ge
Ot d
ealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise (depending on
version):
-
th

e remote control key,
-
th

e electric blind(s),
-
... S

ome functions are not available if the
battery is not sufficiently charged.
8
In the event of a breakdown