roof Peugeot 308 SW BL 2008 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 308 SW BL, Model: Peugeot 308 SW BL 2008Pages: 260, PDF Size: 12.06 MB
Page 51 of 260
i
!
70
COMFORT
SEAT MODULARITY AND VARIOUS CONFIGURATIONS
Examples of configurations 7 seats
It is imperative that the operations
t o c h a n g e t h e e x i s t i n g c o n fi g u r a -
tion are carried out when stationary
(see paragraphs "Rear seats" and
"Additional seats" of the SW with
panoramic roof).
Special features
The side seats of the 2nd row can be
re-aligned, once the central seat has
been removed.
The 2nd row seats can be installed in
the 3rd row.
Conversely, the 3rd row seats cannot
be installed in the 2nd row.
5 seats with additional seats folded
Do not seat passengers in the 3rd
row if the 2nd row seats are in the
fully folded position.
Designed to be modular, your vehicle
offers numerous seat installation and
l o a d i n g c o n fi g u r a t i o n s .
Page 76 of 260
!
i
88
ACCESS
GLASS PANORAMIC ROOF
Component which has a tinted glass
panoramic surface to increase the light
and visibility in the passenger compart-
ment.
Fitted with an electric shutter in several
sections to improve temperature and
noise related comfort. If the shutter meets an obstacle
during operation, you must reverse
the movement of the shutter. To do
this, press the control concerned.
When the driver operates the shut-
ter control, he must ensure that no
one is preventing correct closing of
the shutter.
The driver must ensure that pas-
sengers use the shutter correctly.
Be aware of children when operating
the shutter.
-
manual mode
Pull or press control A gently.
The shutter stops when you release the control. -
automatic mode
Pull or press control A fi r m l y .
One press opens or closes the shutter completely.
Pressing the control again stops the shutter.
Safety auto-reverse
In automatic mode and at the end of its
travel, if the shutter meets an obstacle
while closing it stops and moves back
slightly.
One-touch electric shutter
There are two options for opening and
closing: If the shutter’s supply is cut off, the
safety auto-reverse must be reini-
tialised:
press the control until the
shutter is fully closed.
If the shutter re-opens during the
closing manoeuvre, and immedi-
ately after it stops:
pull the control until the shutter
is fully open,
press the control until the
shutter is fully closed.
The safety auto-reverse function
is not operational during these
operations.
Page 104 of 260
i
i
111
LAYOUT
High load retaining net
Hooked onto the special upper and low-
e r fi x i n g s , t h i s p e r m i t s u s e o f t h e e n t i r e
loading volume up to the roof:
- behind the rear seats (row 2),
- behind the front seats (row 1) when the rear seats are folded.
To use it in row 1:
o p e n t h e c o v e r s o f t h e u p p e r fi x i n g s 1 ,
unroll the high load retaining net,
position one of the ends of the net’s
metal bar in the corresponding upper
fi x i n g 1 , then do the same with the
other end,
slacken the straps fully,
fi x t h e s n a p h o o k o f e a c h o f t h e
straps on the corresponding bar 3 ,
located under the cushion of the
rear seats,
fold the rear seats,
tighten the straps,
check that the net is hooked and
tightened correctly. To use it in row 2:
fold or remove the load space
cover,
o p e n t h e c o v e r s o f t h e u p p e r fi x i n g s 2 ,
unroll the high load retaining net,
position one of the ends of the net’s
metal bar in the corresponding upper
fi x i n g 2 , then do the same with the
other end,
fi x t h e s n a p h o o k o f e a c h o f t h e
straps in the corresponding ring 4 ,
located on the rear seats mechanism
support,
tighten the straps,
check that the net is hooked and
tightened correctly.
When positioning the net, check
that the strap loops are visible from
the boot; this will make slackening
or tightening easier.
This net can be stored in the stor-
a g e t r a y o n t h e fl o o r .
Page 107 of 260
i
114
LAYOUT
High load retaining net
Hooked onto the special upper and low-
e r fi x i n g s , t h i s p e r m i t s u s e o f t h e e n t i r e
loading volume up to the roof behind
the seats of the 2nd row. 12 V accessories socket
In order to connect a 12 V accessory
( m a x p o w e r : 1 0 0 W a t t s ) , r e m o v e
the cap and connect the appropriate
adaptor.
Turn the key to the ignition position.
To use the net in the 2nd row (additional
seats folded or removed):
roll up or remove the load space
screen,
o p e n t h e c o v e r s o f t h e u p p e r fi x i n g s 1 ,
unroll the high load retaining net,
position one of the ends of the net’s
metal bar in the corresponding upper
fi x i n g 1 , then do the same with the
other end,
attach the snap hook of each of the
net’s straps in the corresponding
ring 2 , l o c a t e d o n t h e l o w e r fi x i n g o f
the rear side seat belt,
tighten the straps,
check that the net is hooked and
tightened correctly. Hooks
The hooks permit the securing of shop-
ping bags.
When positioning the net, check
that the strap loops are visible from
the boot; this will make slackening
or tightening easier.
Page 127 of 260
i
132
SAFETY 2 nd row rear centre
seat belt
Installation Removal and storing
Press the red button on the buckle
B , then on the buckle A .
Guide the strap as it rolls up and
bring the tongue B , then A onto the
magnet of the attachment point on
the roof.
3 rd row rear seat belts
Installation
Pull the strap and insert the tongue
C in the buckle, on the boot side trim
side.
Insert the tongue D in the opposite
buckle.
Check the fastening of each buckle
by pulling the strap.
Pull the strap and insert the tongue
A in the left-hand buckle.
Insert the tongue B in the right-hand
buckle.
Check the fastening of each buckle
by pulling the strap.
The seat belts for the rear seats of the
3 rd row are incorporated at the corner
of the corresponding boot pillar and of
the roof. If the two side seats of the 2nd row
are re-aligned, always use the rear
side seat belts.
Removal and storing
Press the red button on the buckle
D , then on the buckle C .
Guide the strap as it rolls up and
bring the tongue D , then C onto the
magnet of the attachment point on
the corresponding boot pillar.
The seat belt for the rear centre seat of
the 2 nd row is incorporated at the rear
left of the roof.
Page 171 of 260
11
176
PRACTICAL INFORMATION
Fascia fuses
T h e f u s e b o x i s p l a c e d i n t h e l o w e r s e c -
tion of the fascia (left-hand side).
Access to the fuses
refer to the paragraph "Access to
the tools". Fuse tables
Fuse N° Rating Functions
G36 - Not used.
G37 5 A T r a i l e r f u s e b o x .
G38 30 A Driver's seat memory unit.
G39 30 A T r a i l e r f u s e b o x s u p p l y .
G40 30 A H i - F i a m p l i fi e r .
Fuse N° Rating Functions
F1 15 A Rear wiper.
F2 - Not used.
F3 5 A Air bags and pretensioners control unit.
F4 10 A Clutch pedal and dual-function brake switches,
electrochromatic interior mirror, air conditioning,
s t e e r i n g w h e e l a n g l e s e n s o r , a u t o m a t i c g e a r b o x ,
switching and protection unit.
F5 30 A Front one-touch electric windows, folding mirrors
supply, glass panoramic roof shutter.
F6 30 A Rear one-touch electric windows.
F7 5 A Front and rear courtesy lights, map reading lights,
r e a r r e a d i n g l i g h t s , s u n v i s o r l i g h t i n g , g l o v e b o x
lighting, portable lamp.
Page 177 of 260
11
!
!
i
182
PRACTICAL INFORMATION Do not disconnect the terminals
while the engine is running.
Do not charge the batteries without
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
Do not push the vehicle to start the
e n g i n e i f i t i s fi t t e d w i t h a 6 - s p e e d
p i l o t e d m a n u a l g e a r b o x .
The batteries contain harmful sub-
stances such as sulphuric acid and
lead. They must be disposed of in
accordance with regulations and
must not, in any circumstances, be
discarded with household waste.
Take used remote control batteries
and vehicle batteries to a special
collection point.
Charging the battery using a
battery charger
Disconnect the battery from the
vehicle.
Follow the instructions for use
provided by the manufacturer of the
charger.
Reconnect starting with the negative
terminal (-).
Check that the terminals and
connectors are clean. If they are
covered with sulphate (whitish or
greenish deposit), remove them and
clean them.
At the risk of discharging the bat-
tery, the deactivated functions can
be reactivated manually.
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions in relation to the level of
charge remaining in the battery.
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
conditioning, the rear screen de-icing...
The deactivated functions are reactivated
automatically as soon as conditions
permit.
It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month. Before disconnecting
the battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery.
Following reconnection of
the battery
Following reconnection of the
battery, switch on the ignition
and wait 1 minute before starting
to permit initialisation of the
electronic systems. However, if
s l i g h t d i f fi c u l t i e s a r e e n c o u n t e r e d
following this operation, contact a
PEUGEOT dealer.
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the glass panoramic roof shutter,
- the GPS satellite navigation
system.
Page 178 of 260
11
!
!
i
182
PRACTICAL INFORMATION Do not disconnect the terminals
while the engine is running.
Do not charge the batteries without
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
Do not push the vehicle to start the
e n g i n e i f i t i s fi t t e d w i t h a 6 - s p e e d
p i l o t e d m a n u a l g e a r b o x .
The batteries contain harmful sub-
stances such as sulphuric acid and
lead. They must be disposed of in
accordance with regulations and
must not, in any circumstances, be
discarded with household waste.
Take used remote control batteries
and vehicle batteries to a special
collection point.
Charging the battery using a
battery charger
Disconnect the battery from the
vehicle.
Follow the instructions for use
provided by the manufacturer of the
charger.
Reconnect starting with the negative
terminal (-).
Check that the terminals and
connectors are clean. If they are
covered with sulphate (whitish or
greenish deposit), remove them and
clean them.
At the risk of discharging the bat-
tery, the deactivated functions can
be reactivated manually.
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions in relation to the level of
charge remaining in the battery.
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
conditioning, the rear screen de-icing...
The deactivated functions are reactivated
automatically as soon as conditions
permit.
It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month. Before disconnecting
the battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the doors
before disconnecting the battery.
Following reconnection of
the battery
Following reconnection of the
battery, switch on the ignition
and wait 1 minute before starting
to permit initialisation of the
electronic systems. However, if
s l i g h t d i f fi c u l t i e s a r e e n c o u n t e r e d
following this operation, contact a
PEUGEOT dealer.
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the glass panoramic roof shutter,
- the GPS satellite navigation
system.
Page 183 of 260
11
ii
PRACTICAL INFORMATION
FITTING ROOF BARS
M a x i m u m a u t h o r i s e d w e i g h t o n t h e
roof rack, for a loading height not
e x c e e d i n g 4 0 c m ( w i t h t h e e x c e p -
tion of bicycle carriers): 80 kg.
I f t h e h e i g h t e x c e e d s 4 0 c m , a d a p t
the speed of the vehicle to the pro-
fi l e o f t h e r o a d t o a v o i d d a m a g i n g
t h e r o o f b a r s a n d t h e fi x i n g s o n t h e
roof.
Be sure to refer to national legis-
lation in order to comply with the
regulations for transporting objects
which are longer than the vehicle.
FITTING ROOF BARS
W h e n fi t t i n g t r a n s v e r s e
roof bars, ensure that they
are positioned correctly as
shown by marks under the
longitudinal roof bars.
Use accessories recommended by
PEUGEOT and follow the accessory
m a n u f a c t u r e r ’ s fi t t i n g i n s t r u c t i o n s .
In order to place a load on the roof,
t r a n s v e r s e r o o f b a r s m u s t b e fi t t e d o n
the longitudinal roof bars.
After putting the load in place and se-
curing it, retighten the transverse roof
bars.
The longitudinal roof bars cannot
be removed.
M a x i m u m a u t h o r i s e d w e i g h t o n t h e
roof bars, for a loading height not
e x c e e d i n g 4 0 c m ( e x c e p t b i c y c l e
carriers): 80 kg.
I f t h e h e i g h t e x c e e d s 4 0 c m , a d a p t
the speed of the vehicle to the con-
dition of the road, to avoid damag-
i n g t h e r o o f b a r s a n d t h e fi x i n g s o n
the roof.
Please refer to national legislation
to comply with the regulations re-
garding the transportation of objects
which are longer than the vehicle.
W h e n fi t t i n g t r a n s v e r s e r o o f b a r s , u s e
t h e f o u r q u i c k - fi t fi x i n g s p r o v i d e d f o r t h i s
purpose:
l i f t t h e c o n c e a l i n g fl a p s ,
o p e n t h e fi x i n g c o v e r s o n e a c h b a r
using the spanner,
p u t e a c h fi x i n g i n p l a c e a n d l o c k
them on the roof one by one,
c l o s e t h e fi x i n g c o v e r s o n e a c h b a r
using the spanner.
Page 184 of 260
11
i
188
PRACTICAL INFORMATION
ACCESSORIES
You can obtain a wide range of ac-
cessories and original parts from the
PEUGEOT network.
These accessories and parts have been
tested and approved for reliability and
safety.
They are all adapted to your vehicle and
b e n e fi t f r o m P E U G E O T ’ s r e c o m m e n d a -
tion and warranty.
The product range offered by PEUGEOT
Accessories is structured around 5 cat-
egories: PROTECTION - TOURING -
IN-CAR TECHNOLOGY - STYLING -
UNIVERSAL.
"Protection": "Touring":
mats ** , boot tray, luggage net,
fi x e d c o a t h o o k o n h e a d r e -
straint, aluminium or PVC door
sills, fragrance cartridges.
anti-theft alarm, window en-
g r a v i n g , w h e e l l o c k s , fi r s t a i d
kit, warning triangle, safety
jacket, stolen vehicle track-
ing system, dog guard, snow
chains. For leisure pursuits: roof bars, bicycle
carrier on towbar, bicycle carrier on roof
b a r s , s k i c a r r i e r , r o o f b o x , b o o s t e r s e a t s
and child seats, side blinds and rear
blind, front centre armrest, CD storage,
under shelf storage.
T r a i l e r t o w b a r w h i c h m u s t b e fi t t e d b y
the PEUGEOT network.
** To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned
and secured correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
VERY COLD CLIMATE SCREEN *
Removable device which prevents the
accumulation of snow at the radiator
cooling fan.
Fitting
Offer up the very cold climate screen
in front of the lower section of the
front bumper.
Press on its periphery to clip its
fi x i n g c l i p s o n e b y o n e .
Do not forget to remove the very
cold climate screen:
- when the outside temperature e x c e e d s 1 0 ° C ,
- when towing,
- at speeds higher than 75 mph (120 km/h).
Removal
Use a screwdriver as a lever to
u n c l i p e a c h fi x i n g c l i p i n t u r n .
* According to country.