ECO mode PEUGEOT 4008 2012 Owners Manual

18
Familiarisation
Monitoring

Manual headlamp adjustment.
Side switch panel
137
1.Open the glove box.
2. Inser t the key.3.
Select the position:"OFF"(deactivation), with "rear facing"child seat, "ON"
(activation), with front passenger or "forwards facing" child seat. 4.Remove the key keeping the switch in the
new position.


Passenger's front airbag
155
B.Deactivation of the ASC/ TCL system.
127 C
.Deactivation of the parking sensors.
148

Passenger safety
120
D.
Deactivation of the Stop & Start (AutoStop & Go) function.

Starting



- Position 1: LOCK

- Position 2: ACC

- Position 3: ON

- Position 4: START

Each press on the START/STOPbutton,
without action on the pedals, changes the mode of the vehicle.


- First press: ACC mode

- Second press: ONmode

- Third press: OFF mode
106
107


Ignition switch

STA R T/STOP button

20
Familiarisation
Driving safely
Stop & Start
(Auto Stop & Go) function
Engine going into STOP mode
119

The "AS&G"
warning lamp comes on in
the instrument panel or the instrument
panel screen and the en
gine is put into
standby after a few seconds:

Engine going into START mode

Deactivation
/ Reactivation

You can deactivate the system at any time
by pressing the "AS&G OFF"
button; the corresponding warning lamp comes on in the
instrument panel or the instrument panel screen.120
120
The system is reactivated automatically every time you star t the engine with the key or with theSTA R T/STOP button. Th
e "AS &G "warning lamp goes off
and the engine restarts automatically:


-
with a manual gearbox;when you fullydepress the clutch pedal.-with a manual gearbox;
with the vehicle
stationary and your foot on the brake pedal,
when you put the gear lever into neutraland release the clutch pedal. In certain condition, START mode may engage
automatically; the "AS&G"warning lamp
flashes then goes off.
In certain circumstances the STOP mode may not be available; the "AS&G"
warning lamp
flashes for a few seconds then goes off.

.
21
Familiarisation
Driving safely

Three transmission modes are available and selectable manually by the driver according to
requirements:
A
.Two wheel drive (2WD),B.Four wheel drive (4WD AUTO),
C.Four wheel drive (4WD LOCK).


Four wheel drive system
1."ON / OFF" button: switches cruise controlon and off.
2. " COAST SET
" button: programme a driving speed then decrease the cruise speed. 3."ACC RES ": increase the cruise speed,
and recall the programmed speed. 4."CANCEL" button: cruise control off. LL
Cruise control "CRUISE"
124
In order to be programmed or activated, the
vehicle speed must be higher than 25 mph (40 km/h), with at least second gear engaged. 122

24
Instruments and controls

















Instrument panel
1.
Rev counter. 2.
Speedometer.
Screen t
ype 2
3.
Instrument panel display screen:


- Warning and status displays.

- Total and tri
p distance recorders.

- Ser vice indicator.

- Coolant temperature.

- Trip computer information.

- Cruise control settin
g.

- Gear shift indicator recommendations.

- Settings menu (display, sound...).

- Fuel level.

- Ambient temperature.

- Transmission mode.

Panel
grouping together the dials and warning/indicator lamps. These inform the driver of the activation/deactivation of a system or of theoccurrence of a fault.
Screen t
ype 1
Management of the display is done using the INFO
button located on the dashboard to the left of the instrument panel.

1
29
Instruments and controls
Warning lampis onCauseAction / Observations
Cruise control
fixed
This comes on when the cruisecontrol has been activated. Press the "ON/OFF" button to activate/deactivate thecruise control.
Active stabilitycontrol and traction control (ASC/TCL)

flashing.Operation of the ASC/ TCL systems. The systems optimise traction and improve the
directional stability of the vehicle.
Adapt your driving and moderate your speed.

fixed. Fault in the ASC/TCL systems. Have it checked by a PEUGEOT dealer or a qualified
workshop.
Stop & Star t(Auto Stop & Go)function
fix
ed. When the vehicle stops (red lights,
traffic jams, ...) the Stop & Star t (AS&G) function has put the engine
into STOP mode. The warnin
g lamp goes off and the engine restarts
automatically in START mode, as soon as you want to move off.

flashes for a few
seconds, then goes off.
STOP mode is temporarily
unavailable. or START mode is invoked
automatically.
See "Stop & Start (AS&G) function" for special cases
with
STOP mode and STA R T mode.
Diesel engine pre-heating fixed. The engine is cold and:
- the ignition switch is at the ONposition (ignition on), or
- the STA R T/STOP
starting button
has been pressed (ignition on).

With key starting, wait until the warning lamp has gone off
before starting.
With the Keyless Entry and Star ting system, the engine will only start after the warning lamp has gone off.
The duration for which the warnin
g lamp is on is determined by
the climatic conditions (up to 30 seconds in severe weather).
If the engine does not star t, switch the ignition off and then onagain and wait again until the warning lamp goes off, then star t
the engine.

1
47
Instruments and controls

Average fuel consumption
(l/100 km or km/l or mpg)

This is the average fuel consumption calculatedsince the trip computer was
last reset.

Average speed
(km/h or mph)

This is the average speedcalculated since the tripcomputer was last reset.


Current fuel consumption
(l/100 km or km/l or mpg)

This is the average fuel consumption calculated over
the last few seconds.

This value may change following achange in the style of driving or the relief.


If dashes "---" are displayed for long periods in place of the digits while driving, contact a PEUGEOT dealer or a qualified workshop.

Resetting the information to zero
When the required information is displayed, press the INFO
button for more than
two seconds to reset all of the information
to zero.
When the ignition is switched on, the zero
reset switches automatically from manual mode to automatic mode.
Automatic
If the ignition key remains in the OFF position
for more than 4 hours, the information is reset
to zero automaticall
y.

48
Instruments and controls
The various menus may change between the type 1
instrument panel and the type 2 instrument panel.
Adjusting vehicle settings
When the vehicle is stationary, it allows theyuser to change the following settings:


- the reinitialisation mode for average fuel consumption andaverage speed,
)Press and hold the INFObutton for a fewseconds to display the menu screen.
)In the menu screen, press the INFO
button
to select a function from the list:
- the
fuel consumption units,
- the temperature displa
y unit,
- the display language,
- activation/deactivation of the sound whenpressing the INFO
button,- the break (rest) reminder display interval,
- restore the factory settings.
To change the settings, you must stopthe vehicle and switch on the ignition.
Apply the parking brake and place the gear lever in neutral. With the ignition on
, press the INFObutton
on the dashboard, to the left of the instrumentpanel, several times in succession until the
"SETTINGS MENU" screen is displayed.


Operation
MENU1/3:-1 - 2, A - M, A - P*
(choice of the type of reset of average fuel consumption andaverage speed),

- AVG UNIT(choice of the fuel consumption
units),

- choice of the temperature display unit,-LANGUAGE(option of the display
language),

*
According to display language.
For your safety, when the vehicle is moving
, the function settings are not displayed when you press the INFObutton.

1
49
Instruments and controls
MENU2/3:-a/b (option of displaying a different language in the instrument panel screen
and the navigation screen),
-
activation / deactivation of the INFObutton sound
,

- ALERT(changing of the "REST REMINDER" display interval),
-
selection of the sound
of the direction
indicators,-activation / deactivation of the current fuel consumption ,



Press and hold the INFO
button for afew seconds to return to the previous screen. When the menu screen is displayed, if no operation is carried out within15 seconds, the Settings Menu screenis displayed.
MENU 3
/3:-RESET(restore factory settings).
Choice of the reset mode for average fuel consumption and average speed
You can choose between two average fuelconsumption and average speed reset modes:
- automatic reset,- manual reset.
In th
e menu screen: ) press the INFObutton to select:
)
press and hold the INFObutton for a few seconds to switch in succession fromreset mode 1- A (automatic) *

to reset
mode 2 - M - P (manual) * .
The mode selected is confirmed.


Choice of the fuel consumptionunit

The distance, speed and quantity of fuel units
will also be changed in accordance with your choice of fuel consumption unit.
In th
e menus screen:)
press the INFObutton to select "UNIT".
)
press and hold the INFO
button for
a few seconds to display the "AVG UNIT"screen.
*
According to display language.

50
Instruments and controls

If the battery is disconnected, thesettings memory is cleared andthe default unit (km/L) is restored automatically.

If the battery is disconnected, the settings memory is cleared and the default unit (°C) is restored automatically.

)press the INFO
button to scroll the units(km/L, L/10 0km, mpg (US), mpg (UK) and
RETURN) in succession, )press and hold the INFO
button for a few
seconds to confirm your selection.


Choice of the temperature
display unit
)
press and hold the INFObutton for a few seconds to scroll the units (°C and °F) in succession.
The mode selected is confirmed. In th
e menu screen:)
press the INFObutton to select the
temperature unit setting symbol(thermometer):


Choice of the display LANGUAGE

In the menu screen: )press the INFO
button to select"LANGUAGE":
)press and hold the INFO
button for a fewseconds to display the "LANGUAGE"screen:

1
51
Instruments and controls

If you select the "---" setting, nomessage will be displayed in messagedisplay situations.


If the battery is disconnected, thesettings memory is cleared and the default language (ENGLISH) is restored automatically.
)press the INFO
button to scroll thelanguages (Japonais, English, Deutsch,
Français, Espanol, Italiano, Russe "---" and
RETURN) in succession, )press and hold the INFO
button for a few seconds to confirm your selection.
Activation / deactivation of language cooperation between
the instrument panel screen and
the navigation screen *
You can choose to have the language used bythe instrument panel screen linked to that of the navigation screen.
In th
e menus screen:
) press and hold the INFO
for a few seconds to run through the choices ( A-1"cooperation activated" **
and M-2-P"cooperation deactivated" ** ).
The selected mode is confirmed.


If the battery is disconnected, thesettings memory is cleared andthe default unit (A - 1
"cooperationactivated") is restored automatically.

)
press the INFO
button to select
the symbol for activation /
deactivation of languagecooperation.

**
Accordin
g to display language.*
Depending on equipment.