lights Peugeot 406 Break Dag 2003 Owner's Guide

17-02-2003
Rear lights, estate
Wing lights
To remove the trim, pull the handle towards you and release the panelupwards.Open the flap using the ignition key. Remove the connector by pressing the metal bar
A.
Unscrew the wing nut B.
Release the light. To gain access to the bulbs, press
the tabs and release the bulb holder.
1 - Brake/side lights (P 21/5 W).
2 - Direction indicators (P 21 W). Change the faulty bulb.
MAINTENANCE OF YOUR 406
39

17-02-2003
Tailgate lights Open the flap using the cut-out pro- vided. Disconnect the connector by releas- ing tab A.
Unscrew the two nuts. Remove the light by squeezing the two tabs B. Extract the bulb holder by pressingthe tabs
C.
Change the faulty bulb.
1 - Side lights (P 21/5 W).
2 - Reversing lights (P 21 W).
3 - Fog lamp (P 21 W). Number plate lights (W 5 W)
Remove the translucent protector.Change the faulty bulb.
MAINTENANCE OF YOUR 406
40

17-02-2003
Engine compartment fuses Fuse box
To access the fuse box in the engine compartment (beside the battery),
unclip the cover. Carefully close the cover when you have finished.The electrical system of your vehicle is designedto operate with standardor optional equipment.
Before installing other electricalequipment or accessories on yourvehicle, contact a PEUGEOT
dealer. Some electrical accessories or the way in which they are fitted canhave damaging effects on theoperation of your vehicle; theelectronic control circuits, theaudio circuit and the batterycharging circuit. PEUGEOT will not accept respon- sibility for the cost incurred inrepairing your vehicle or for recti-fying the malfunctions resultingfrom the installation of acces-sories not supplied and not rec-ommended by PEUGEOT and notinstalled in accordance with itsinstructions, in particular wherethe equipment in question con-sumes more than 10 mil-liamperes. * The maxi-fuses provide addition- al protection for the electrical sys-
tems. All work must be carried out
by a PEUGEOT dealer.
Fuse N¡ Rating Functions
1* 10 A Reversing lights - Double injection relay - Engine oil temperature - Oil level -
Air conditioning compressor.
2* 15 A Fuel pump - Canister solenoid valve.
3* 10 AElectronic Control unit.
4* 10 AEngine control unit and automatic gearbox.
5 10 A Particulate Emission Filter control unit -
Rear windscreen relay.
6 15 A Front fog lamps.
7 20 AHeadlamp wash.
8* 20 ADirect petrol injection engine control unit - Clutch pedal.
9* 15 A Left-hand dipped beam lights.
10* 15 A Right-hand dipped beam lights.
MAINTENANCE OF YOUR 406
44

17-02-2003
Fuse N¡ RatingFunctions
11* 10 ALeft-hand main beam.
12* 10 A Right-hand main beam.
13* 15 AHorn.
14 10 AFront and rear screen wash pump.
15* 30 A Ignition coil - Windscreen wiper - Oxygen sensor - Oil pressure - Injection system.
16* 30 A Air pump and oil temperature - Oil level - Brake lights function - Alternator - Water in diesel
detector - Injection relay control.
17* 30 A Passenger's electric seat.
18 40 A Heater blower - Starter - Windscreen wiper slow speed.
MAINTENANCE OF YOUR 406 45

17-02-2003
Fuse N¡ RatingFunctions
19 10 ARear fog lamps.
20 10 ARear right and front left side light.
21 10 ARear left and front right side light.
22 10 A Glove box lighting - Map reading light - Courtesy mirror light - Front and rear courtesy
lights - Lighting for electric windows pad and Electrochrome rear view mirror.
23 20 A Lighter.
24 ÐNot used.
25 20 AAudio equipment.
26 ÐNot used.
27 5 ARear window relay.
28 15 AHeated seats.
R5 AReplacement fuse.
R2 10 A Replacement fuse.
R3 30 AReplacement fuse.
R4 20 AReplacement fuse.
R5 15 A Replacement fuse.
MAINTENANCE OF YOUR 406 43

17-02-2003
BATTERY
To charge the battery using a battery charger:
Ð Disconnect the battery,
Ð Follow the instructions for use given by the battery charger manufacturer,
Ð Reconnect starting with the negative (Ð) terminal,
Ð Check that the terminals and connectors are clean. If they are covered with sul-phate (white or greenish deposit), disconnect them and clean them.
To start the vehicle from another battery:
Ð Connect the red cable to the positive (+) terminals of the two batteries,
Ð Connect one end of the green or black cable to the negative (Ð) terminal of the slave battery,
Ð Connect the other end of the green or black cable to an earth point on the bro- ken down vehicle, as far as possible from the battery,
Operate the starter, let the engine run.
Wait for the engine to return to idle, then disconnect the cables.
Ð Never disconnect a terminal when the engine is running.
Ð Never charge a battery without first disconnecting the terminals.
Ð Close the sunroof before disconnecting the battery. If it does not operate normally following re-connection of the battery, you must
re-initialise it by turning the control to the maximum tilt position and pressing it for a few seconds.
Ð After every reconnection of the battery, switch on the ignition and wait 1 minute before starting to allow the electronic systems to be initialised. Ifslight difficulties are experienced after this, please contact a PEUGEOT deal-
er.
It is advisable to disconnect the battery if the vehicle
is not to be used for a period of more than one month.
Economy mode
With the engine switched off and the ignition key in the "running" or"accessories" position for about half
an hour, certain electrical equipment(displays, instrument panel, warninglights, courtesy lights, electric win-
dows, wipers etc.) will switch offautomatically to avoid draining the
battery. Once the electrical equipment goes into economy mode, it is necessaryto start the engine to enable theequipment to work again.
MAINTENANCE OF YOUR 406
46

17-02-2003
TOWING A TRAILER,
CARAVAN, BOAT ETC.
Only use original PEUGEOT tow bars that have been tested andapproved from the design stage ofyour vehicle. The tow bar must be fitted by a
PEUGEOT dealer.
Your vehicle is basically designed for transporting people and luggage butit may also be used for towing a
trailer. Driving with a trailer subjects the towing vehicle to more significantstress and its driver must be particu-larly careful. Air density decreases with altitude, thus reducing engine performance.The maximum towing load must
be reduced by 10 % for every
1 000 metres of altitude. Driving advice Distribution of loads: Distribute the
load in the trailer so that the heaviest items are as close as possible to theaxle and the nose weight approach-es the maximum permitted withoutexceeding it. Cooling:
Towing a trailer on a slope
increases the temperature of thecoolant. As the fan is electrically controlled, its cooling capacity is not dependenton the engine speed.
On the contrary, use a high gear to lower the engine speed, and reduceyour speed. The maximum towing speed on a long slope depends on the gradientand the outside temperature. For vehicles fitted with a direct injec- tion petrol engine, after towing or dri-ving at high speed for a long periodof time, the fan may operate forapproximately 6 minutes. In all cases, pay attention to the coolant temperature. If the warning light comes on, stop
the vehicle and switch off the engineas soon as possible. Tyres:
Check the tyre pressures of
the towing vehicle and the trailer,observing the recommended pres-sures. Brakes: Towing increases the braking
distance. Lights: Check the electrical sig-
nalling on the trailer.Side wind: Take into acount the
increased sensitivity to side wind.
MAINTENANCE OF YOUR 406 49