maintenance Peugeot 406 Break Dag 2003 Owner's Guide

17-02-2003
MAINTENANCE OF YOUR 40635
Ð The jack is fitted with a system
which enables it to be folded or
unfolded rapidly. Take the jackfrom the toolkit and fold it by press-ing the ends A. Place the jack at
one of the locations Eunderneath
the vehicle (as close as possible tothe wheel to be changed) andunfold it by pulling the ends A.
Ð Extend the jack using the wheel- brace 1and the extension 3.
Ð Take out a wheel bolt at the top and fit the centralising tool 2.
Ð Loosen the wheel bolts and remove the wheel. Fitting a wheel
Ð Position the wheel using the cen-
tralising tool to assist you.
Ð Tighten the bolts by hand, and remove the centralising tool.
Ð Partly tighten the bolts using the wheelbrace.
Ð Fold the jack and remove it.
Ð Fully tighten the wheel bolts using the wheelbrace.
Ð Replace the wheel trim, except in the case of a space-saver wheel, by starting with the valve andpressing on using the palm of yourhand. For your safety, alwayschange the wheel:
Ð on level, stable, non-slippery ground,
Ð with the handbrake applied,
Ð with first or reverse gear engaged (position Pfor the
automatic gearbox).
Ð Never go underneath a vehicle which is supported only by a jack (use a ramp).
After changing the wheel
Ð have the tightening of the bolts and the tyre pressure checked by a PEUGEOT dealer as soonas possible,
Ð have the punctured tyre repaired and refit it to the vehi-cle as soon as possible.
7 seater Estate model The space-saver spare wheel fit- ted with a 125/80R15 tyre mustonly be used as a short-term mea-
sure. Tyre pressure is 61 lb in2(4.2 bars), maximum speed is 50 mph (80 km/h).

17-02-2003
MAINTENANCE OF YOUR 406
36
Anti-theft bolts* If your wheels are fitted with an anti- theft bolt (one per wheel), thechrome trim and then the plasticcover must be removed using tool 7,
before unscrewing the bolt using oneof the two anti-theft sockets (whichwere given to you on delivery of yourvehicle along with the duplicate keysand the confidential card) and thewheel brace 1.
Note: make a careful note of the
code number engraved on the head
of the anti-theft socket. This willenable you to obtain duplicate anti-
theft sockets from a Peugeot dealer.
* According to model and destination.
Special features of alloy wheels Bolt covers Alloy wheel bolts are covered by chrome trims. Use tool 7to remove the trims before
slackening the bolts.Fitting the spare wheel If your vehicle is fitted with a steel spare wheel, when fitting it, it is normal to notice when tightening the
bolts that the washers do not come
into contact with the rim. The sparewheel is secured by the cone-shapeof each bolt. Fitting snow tyres If you fit snow tyres mounted on steel wheels to your vehicle, it is essential
to use special bolts available from
your PEUGEOT dealer.

17-02-2003
Amber bulbs must be replaced by bulbs of iden-tical specification and
colour.
In certain weather conditions (lowtemperatures, humidity), the
presence of condensation onthe inside of the headlampglass is normal; it disappears a
few minutes after the lights havebeen switched on.
CHANGING A BULB 1 - Dipped beam headlamps 2 - Main beam headlamps 2 bulbs (H7-55 W)
Ð Press the tab and remove the protective cover corresponding to the faulty bulb.
Ð Disconnect the connector.
Ð Press the end of the securing clip to remove it. Change the bulb.
Ð When fitting, ensure that the direction notches are positioned correctly and that the securing clip is corrrectly fixed.
Ð Reconnect the connector.
Ð Refit the protective cover. 3 - Side lights (W 5 W)
Turn the socket using the lever and remove it. Change the bulb.
4 - Direction indicators (P 21 W)
Turn the bulb holder a quarter turn and remove it. Change the bulb. Note: only handle H7 bulbs using a dry cloth.
To replace the left-hand bulbs, remove the protective battery cover. Direction indicator (WY 5 W)
Ð Pull the rear section of the trans-
parent cover and release the
assembly.
Ð Turn the connector a quarter turn and remove it.
Ð Change the bulb.
MAINTENANCE OF YOUR 406 37

17-02-2003
Third brake light - saloon (5 W5W bulbs) Lower the two metal clips on either side of the light and slide the cover
towards the rear.
Remove the bulb-holder.Change the faulty bulb.Rear lights, saloon
1 - Direction indicators (P 21 W).
2 - Reversing lights (P 21 W).
3 - Brake lights/Side lights (P 21/5 W).
4 - Side lights (P 21/5 W).
5 - Fog lamp (P 21 W). These 5 bulbs are changed from inside the boot:
Ð remove the retaining clips then release the carpet,
Ð remove the connector by pressing the tab
A,
Ð remove the bulb holder by squeezing the tabs,
Ð change the faulty bulb.
MAINTENANCE OF YOUR 406
38

17-02-2003
Tailgate lights Open the flap using the cut-out pro- vided. Disconnect the connector by releas- ing tab A.
Unscrew the two nuts. Remove the light by squeezing the two tabs B. Extract the bulb holder by pressingthe tabs
C.
Change the faulty bulb.
1 - Side lights (P 21/5 W).
2 - Reversing lights (P 21 W).
3 - Fog lamp (P 21 W). Number plate lights (W 5 W)
Remove the translucent protector.Change the faulty bulb.
MAINTENANCE OF YOUR 406
40

17-02-2003
Rear lights, estate
Wing lights
To remove the trim, pull the handle towards you and release the panelupwards.Open the flap using the ignition key. Remove the connector by pressing the metal bar
A.
Unscrew the wing nut B.
Release the light. To gain access to the bulbs, press
the tabs and release the bulb holder.
1 - Brake/side lights (P 21/5 W).
2 - Direction indicators (P 21 W). Change the faulty bulb.
MAINTENANCE OF YOUR 406
39

17-02-2003
Tailgate lights Open the flap using the cut-out pro- vided. Disconnect the connector by releas- ing tab A.
Unscrew the two nuts. Remove the light by squeezing the two tabs B. Extract the bulb holder by pressingthe tabs
C.
Change the faulty bulb.
1 - Side lights (P 21/5 W).
2 - Reversing lights (P 21 W).
3 - Fog lamp (P 21 W). Number plate lights (W 5 W)
Remove the translucent protector.Change the faulty bulb.
MAINTENANCE OF YOUR 406
40

17-02-2003
CHANGING A FUSE The fuse boxes are under the fascia and in the engine compartment. Fascia fuse box
Turn the three screws a quarter turn with a coin. Pull at Aand tilt the
cover to access the fuses. Removing and changing a fuse Before changing a fuse you must find out the cause of the fault and have it put
right. The fuse numbers are indicated on the fuse box. Use the special pliers
Aattached to the box.
Always change a faulty fuse for one of the same rating.
Correct Incorrect Pliers A
Remove the fascia panel lower trim to access the built-in systems interface.
Fuse n o
. Rating Functions
A 20 A Locking/Unlocking.
B 10 A Rear fog lamps.
.
C 40 A Demisting of mirrors.
D 15 A Rear screen wiper.
E 30 A Electric windows.
F 15 A Supply to: Instrument panel,
Display, Audio equipment,Satellite navigation system,Air conditioning.
MAINTENANCE OF YOUR 406 41

17-02-2003
Engine compartment fuses Fuse box
To access the fuse box in the engine compartment (beside the battery),
unclip the cover. Carefully close the cover when you have finished.The electrical system of your vehicle is designedto operate with standardor optional equipment.
Before installing other electricalequipment or accessories on yourvehicle, contact a PEUGEOT
dealer. Some electrical accessories or the way in which they are fitted canhave damaging effects on theoperation of your vehicle; theelectronic control circuits, theaudio circuit and the batterycharging circuit. PEUGEOT will not accept respon- sibility for the cost incurred inrepairing your vehicle or for recti-fying the malfunctions resultingfrom the installation of acces-sories not supplied and not rec-ommended by PEUGEOT and notinstalled in accordance with itsinstructions, in particular wherethe equipment in question con-sumes more than 10 mil-liamperes. * The maxi-fuses provide addition- al protection for the electrical sys-
tems. All work must be carried out
by a PEUGEOT dealer.
Fuse N¡ Rating Functions
1* 10 A Reversing lights - Double injection relay - Engine oil temperature - Oil level -
Air conditioning compressor.
2* 15 A Fuel pump - Canister solenoid valve.
3* 10 AElectronic Control unit.
4* 10 AEngine control unit and automatic gearbox.
5 10 A Particulate Emission Filter control unit -
Rear windscreen relay.
6 15 A Front fog lamps.
7 20 AHeadlamp wash.
8* 20 ADirect petrol injection engine control unit - Clutch pedal.
9* 15 A Left-hand dipped beam lights.
10* 15 A Right-hand dipped beam lights.
MAINTENANCE OF YOUR 406
44

17-02-2003
Fuse N¡ RatingFunctions
11* 10 ALeft-hand main beam.
12* 10 A Right-hand main beam.
13* 15 AHorn.
14 10 AFront and rear screen wash pump.
15* 30 A Ignition coil - Windscreen wiper - Oxygen sensor - Oil pressure - Injection system.
16* 30 A Air pump and oil temperature - Oil level - Brake lights function - Alternator - Water in diesel
detector - Injection relay control.
17* 30 A Passenger's electric seat.
18 40 A Heater blower - Starter - Windscreen wiper slow speed.
MAINTENANCE OF YOUR 406 45