display Peugeot 406 C 2003 Owner's Guide

24-03-2003
AUTOMATIC SWITCHING ON OF THE LIGHTS Side lights and dipped beam head- lamps switch on automatically if the
light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function:
☞ Place the key in the accessories position (1st notch),
☞ Press the end of the lights stalkfor more than two seconds.
Note: In foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located in the windscreen behind
the mirror. It is used for automaticswitching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multifunction display. Note: Always operate the lighting
controls manually where this is pos- sible. Disarming Disarming of the function is accom- panied by an audible signal and themessage "Automatic lighting of
the headlamps deactivated" on the
multifunction display. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is however possible to disarm this
function and switch off the lights by: - manually switching off the lights using the lights stalk,
- switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights comeon). The driver is alerted by the flashingof the ''dipped beam'' warning lighton the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute.
To do this:
☞ place the lights stalk in the AUTO
position,
☞ place the key in the accessories position (first notch),
☞ press the end of the lights stalk formore than two seconds,
☞ place the lights stalk in the 0posi-
tion,
☞ flash the headlamps,
☞ get out of the car and lock it.
YOUR 406 COUPE IN DETAIL 103

24-03-2003
WINDSCREEN WIPER STALK Front windscreen wipers2. Rapid wipe (heavy rain)
1 . Normal wipe (moderate rain).
AUTO Automatic wipe.
0 .Off.


. Single wipe (press downwards). Operation In position
1or 2, when the vehicle
stops, the windscreen wiper changes to a lower wiping speed, thenresumes its initial speed when thevehicle starts again. When the ignition has been switched off for more than a
minute with the stalk in the AUTOposition, it is necesary to reacti-vate this function. To do this, move
the stalk to any position, then move itback to the AUTOposition.
Automatic wipe In the AUTOposition, the wiper
operates automatically and adjusts
its speed to the intensity of the rainfall. Operating check ActivationActivation of the function is accom- panied by the message "Automatic
wiper activated" on the multifunc-
tion display. In the event of malfunction in the
AUTO position, the windscreen
wiper will operate in downgrade mode. Have the system checked by a
PEUGEOT dealer.
YOUR 406 COUPE IN DETAIL
104
Do not cover the rain detector located on thewindscreen behind the
interior mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not inthe automatic position.
In winter, it is advisable to wait for the windscreen to completelyclear of ice before operating theautomatic wipe.
W indscreen and headlamp wash
Pull the windscreen wiper stalk towards you. The windscreen wash then the wind- screen wipers operate for a fixedperiod. The windscreen wash and headlamp wash operate simultaneously for twoseconds, only if the headlamps are
on.

24-03-2003
TRIP COMPUTERDisplay B Display C
- the range
- the distance travelled
- the average consumption
- the current consumption
- the average speed
Zero reset Press the stalk for more than two seconds. Pressing the button on the end of the
wash/wipe stalkenables the following data to
be displayed:
-the current consumption and the range,
- the average consumption, the distance travelled and the average speed calculated over a period "1",
- the average consumption, the distance travelled and theaverage speed calculated over a period "2".
Periods "1"and "2"are defined by the frequency of the zero
reset. They allow, for instance, daily calculations over period"1" and monthly calculations over period "2".
Zero reset When the required period is displayed, press the stalk for more than two seconds.
YOUR 406 COUPE IN DETAIL
116

24-03-2003
Range The display shows the distance that can still be covered with the fuelremaining in the tank. Note:this figure may rise if there is a
change in driving style or road sur- face, causing a significant drop incurrent fuel consumption. If there are less than 3 litres of fuel in the tank, only three segments will bedisplayed. A
verage consumption
This is the ratio between the amountof fuel consumed and the distancetravelled since the computer was lastreset to zero.
Current fuel consumption This gives the fuel consumption recorded during the last two sec-
onds. This function is only displayedwhen the vehicle is travelling at morethan 12 m.p.h. (20 km/h). A
verage speed
This is obtained by dividing the dis-tance travelled by the period of timethe vehicle has been in use (with theignition on), since the computer waslast reset to zero. Distance travelled This shows the distance travelled since the computer was last reset tozero. After the trip computer has been reset to zero, the range databecomes meaningful only after thevehicle has been in use for a certainperiod. If horizontal segments are displayed instead of figures when driving, con-
tact a PEUGEOT dealer.
YOUR 406 COUPE IN DETAIL
117

24-03-2003
124DRIVING YOUR 406 COUPE
AUTOMATIC AUTOADAPTIVE GEARBOX The 4-speed automaticgearbox offers the comfort of integral automatic
operation , enhanced by a sportprogramme (switch A) and a snowprogramme
(switch B).
Gear selection gate ☞ Move the lever in the gate to select one of the positions. Once the position is selected, the indicator light for that position illuminates on the instrument panel
display.
P Park: for immobilising the vehicle and for startingthe engine, with the
handbrake on or off. R Reverse: this must be engaged when the vehicle is stationary and the engine
at idle.N Neutral: for startingthe engine and for parking, with the handbrake on.
D Drive: for driving in autoadaptive mode (automatic changing of the four gears).
3. For driving in townor on winding roads (automatic changing of the first three
gears only).
2. For driving in the mountainsor for towing a trailer (automatic changing of
the first two gears only).
1. For use on steep gradients (selection of first gear only).
Special feature of the gearbox (2 litre petrol engine)Selection of first gear is by pressing button Cwith the lever in position 2.
To exit first gear, press button Cagain or move the selector lever.
V6 engine 2 litre engine

24-03-2003
DRIVING YOUR 406 COUPE
128
Handbrake Applying When parking, pull the handbrake to immobilise your vehicle. Warning: when parking on a slope,
direct your wheels towards the pave- ment and apply the handbrake. Releasing Pull the handle and press the button to release the handbrake.
Disarming the ESP / ASR systems In certain conditions (vehicle stuck in
mud or snow, or on loose ground...),it could prove useful to disarm theASR system to make the wheelsspin and regain grip. ☞
Press the switch "ESP OFF",
situated to the left of the steering wheel.
The switch lights up and the indicatorlights come on, accompanied by themessage ''ASR/ESP de-activated''
on the multifunction display: the ESP
and ASR systems no longer affectthe operation of the engine or thebrakes. They engage again:☞ automatically when the ignition is
switched off,
☞ manually by pressing the switchagain. The ESP system offersincreased safety duringnormal driving, but shouldnot incite the driver to take
risks or to drive at high speed.The operation of the system isassured to the extent to which therecommendations of the manufac-turer regarding the wheels (tyresand wheel rims), the braking com-ponents, the electronic compo-nents and the assembly andrepair procedures within thePEUGEOT network are respect-ed.After an accident or impact, havethe system checked by a
PEUGEOT dealer.
Operating check When a system malfunctionoccurs, the switch lightflashes and the indicatorlight comes on.
Contact a PEUGEOT dealer tocheck the system.
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP) These systems are linked and com-
plement the ABS.
The ASR system optimises drive to prevent the wheels skidding, by act-ing on the brakes of the drive wheelsand on the engine. It also allows thedirectional stability of the vehicle tobe improved on acceleration. Ifthere is a variation between the tra-jectory followed by the vehicle and
that required by the driver, the ESPsystem automatically acts on theengine and the brake of one or morewheels, in order to put the vehicleback on course.
Operation of the ASR and ESP systems
When one of these two sys-tems is operating, this lightflashes.

24-03-2003
DRIVING YOUR 406 COUPE129
AIR BAGS
The air bags have been designed to maximise the safety of the occupantsin the event of serious collisions.They work in conjunction with theforce-limiting seat belts. The electronic detectors register and analyse any abrupt deceleration ofthe vehicle: if the triggering thresholdis reached, the air bags inflateinstantly and protect the occupantsof the vehicle. Immediately after the impact, the air bags deflate rapidly so that they donot hinder the visibility of the occu-pants nor their exit if necessary fromthe vehicle. The air bags are not deployed in the case of collisions which are not seri-
ous, for which the seat belt is suffi-cient to ensure maximum protection.The seriousness of a collisiondepends on the nature of the obsta-cle and the speed of the vehicle atthe moment of the collision. Air bags only operate when the ignition is switched on. Note:
the gas escaping from the air
bags can be a minor irritant. FRONT AIR BAGSThese are folded in the centre of the steering wheel for the driver and in
the fascia for the front passenger.
They are deployed simultaneously,except in cases where the passen-ger air bag is disarmed.
Front air bag fault If this warning light comes on, accompanied by anaudible signal and the mes-
sage "Air bag fault" on the
multiÐfunction display, contact a
PEUGEOT dealer to have the sys-tem checked. Passenger air bag precautions For a vehicle fitted with a passenger air bag disarming switch:
- disarm the airbag if you installa rear-facingchild seat on thefront passengerseat,
- arm the air bag for an adult pas-
senger.
For a vehicle not fitted with a pas-senger air bag disarming switch: - do not install a rear-fac-ing child seat on thefront passenger seat.
Never place your feet or any objecton the fascia.

24-03-2003
DRIVING YOUR 406 COUPE
130
Operating check This is confirmed by an indi- cator light, accompanied byan audible signal and a
message on the multifunction dis-
play. With the ignition on (2nd notch), illu- mination of this warning light accom-panied by an audible signal and themessage "Passenger air bag dis-
armed" on the multifunction display,
indicates that the passenger air bagis disarmed (switch in the "OFF"
position).
Disarming the passenger air bag*
To
ensure the safety of your child,
it is essential to disarm the pas- senger air bag when you install arear-facing child seat on the frontpassenger seat. ☞ With the ignition switched off, insert the key into the passengerair bag disarming switch 1, turn it
to the "OFF"position, then
remove the key keeping the slot inthis position.
The air bag warning light on theinstrument panel is lit throughout thedisarming process. In the "OFF" position, the passenger
air bag will not be triggered in the event of an impact. As soon as the child seat is removed, turn the air bag slot to the"ON" position to re-activate the air
bag and thus ensure the safety ofyour passenger in the event of animpact.
* According to destination. SIDE AIR BAGS The side air bags are incorporated into the backs of the front seats, onthe door side. They are deployed independently of
each other, on whichever side thecollision occurs.
Operating check This is confirmed by an indicator light, accompanied by an audiblesignal and a message on the
multifunction display.
If this indicator light comeson, accompanied by an audi-ble signal and the message"Air bag fault" on the
multifunction display, contact
a PEUGEOT dealer to have the system checked.

24-03-2003
DRIVING YOUR 406 COUPE
130
Operating check This is confirmed by an indi- cator light, accompanied byan audible signal and a
message on the multifunction dis-
play. With the ignition on (2nd notch), illu- mination of this warning light accom-panied by an audible signal and themessage "Passenger air bag dis-
armed" on the multifunction display,
indicates that the passenger air bagis disarmed (switch in the "OFF"
position).
Disarming the passenger air bag*
To
ensure the safety of your child,
it is essential to disarm the pas- senger air bag when you install arear-facing child seat on the frontpassenger seat. ☞ With the ignition switched off, insert the key into the passengerair bag disarming switch 1, turn it
to the "OFF"position, then
remove the key keeping the slot inthis position.
The air bag warning light on theinstrument panel is lit throughout thedisarming process. In the "OFF" position, the passenger
air bag will not be triggered in the event of an impact. As soon as the child seat is removed, turn the air bag slot to the"ON" position to re-activate the air
bag and thus ensure the safety ofyour passenger in the event of animpact.
* According to destination. SIDE AIR BAGS The side air bags are incorporated into the backs of the front seats, onthe door side. They are deployed independently of
each other, on whichever side thecollision occurs.
Operating check This is confirmed by an indicator light, accompanied by an audiblesignal and a message on the
multifunction display.
If this indicator light comeson, accompanied by an audi-ble signal and the message"Air bag fault" on the
multifunction display, contact
a PEUGEOT dealer to have the system checked.

24-03-2003
MAINTENANCE OF YOUR 406 COUPE37
CHANGING A FUSE The fuse boxes are under the fascia and in the engine compartment. Fascia fuse box T
urn the three screws a quarter turn
with a coin. Pull at Aand tilt the cover to access
the fuses. Removing and changing a fuse Before changing a fuse you must find out the cause of the fault and have it put
right. The fuse numbers are indicated on the fuse box. Use the special pliers
Aattached to the box.
Always change a faulty fuse for one of the same rating.
Correct Incorrect Pliers AFuse no. Rating FunctionsA 20 A Locking/Unlocking.
B 10 A Rear fog lamps.
C 40 A Demisting the mirrors.
D— Not used.
E 30 A Electric windows.
F 15 A Supply to instrument panel -
Display - Audio equipment -Satellite navigation system - Air conditioning.
Remove the fascia lower trim to access the built-in systems interface.