tyre pressure Peugeot 406 C 2003 Owner's Manual

24-03-2003
MAINTENANCE OF YOUR 406 COUPE23

All driving conditions. oArduous conditions. * According to destination.
A
AND C SERVICE LEVELS AND THE INTERMEDIATE VISIT
- Oil filter- Fuel filter* (Petrol)- Fuel filter element (diesel).- Air filter element- Spark plugs (petrol)
- Engine oil- Bleed fuel filter (diesel)
- Engine oil (check + top-up)- Manual gearbox oil (check + top-up)- Battery (check + top-up) if cap is removable- Screen wash front/rear (check + top-up)- Coolant (check + top-up)- Brake fluid (check + top-up)- Power steering fluid (check + top up according to specification)- Operation of lights and indicators- Condition of glass, headlamp and light lenses and mirrors- Horn- Windscreen washer jets-Condition of wiper blades- Condition and tension of the ancillary drive belts- Handbrake- Condition of hydraulic circuits (hoses and covers)- Condition of rubber boots and gaiters- Brake pads o- Play in hubs, link rods, ball joints, flexible mountings- Shock absorbers-Rear drum brake lining wear- Condition and pressure of tyres (including spare wheel)- Emission control check as per current legislation (petrol)- Smoke opacity (diesel)- Passenger compartment filter (according to specification) o-Visual check of the whole vehicle
DRAIN/REFILL
REPLACE
LEVEL
CHECK

ROAD TEST
- Courtesy vehicle
SERVICE*
LevelOperations Description of operation 1st Service
ACIntermediate

24-03-2003
DRIVING YOUR 406 COUPE127
CRUISE CONTROL Cruise control enables the vehicle to maintain a steady speed pro-
grammed by the driver, regardless ofthe road characteristics and withoutthe driver having to touch the accelerator or brake pedals. In order for it to be memorised, the vehicle speed must be greater than25 mph (40 km/h) or 37 mph (60 km/h), depending on the engine,and fourth gear at least must beengaged (second gear for the auto-matic gearbox). Operation ☞
Place switch 1in the ONposition.
A speed can be memorised.
☞ Place switch 1in the OFF position
to cancel.
Memorising a speedAs soon as you reach the chosen speed, press button 2or 3. This
memorises the speed, which will be
maintained automatically. Note:
It is possible to accelerate and drive
momentarily at a speed greater than the memorised speed. When the acceleratorpedal is released, the vehicle will return tothe memorised speed. Cancelling the memorised speed If you wish to cancel the memorised speed: ☞ Press button 4or the brake or
clutch pedal.
Recalling the memorised speedAfter cancellation, press button 4.
Y our vehicle will return to the last
memorised speed. Changing a memorised speed
To memorise a speed higher than
the previous one: ☞ press button 3;
☞ release it when you have reached the required speed.
To memorise a speed lower than the
previous one: ☞ press button 2;
☞ release it when you have reached the required speed.
Cancelling the cruise control ☞ place switch 1in the OFF position
or switch off the ignition.
Do not use cruise control on slippery roads or inheavy traffic. THE ABS ANTI-LOCK BRAKINGSYSTEM
When used with approved tyres in
good condition, the ABS increasesthe stability and manoeuvrability ofyour vehicle, particularly on poor orslippery road surfaces. The anti-lock braking system comes into operation automatically whenthere is a risk of wheel lock.
EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system enables the optimum braking pres-
sure to be reached more quickly,thus reducing the stopping distance. It is triggered by the speed at which
the brake pedal is activated. The
effect of this is a reduction in theresistance of the pedal and an
increase in braking efficiency. The normal operation of the ABSmay make itself felt by slightvibrations of the brake pedal. In emergency braking, press very firmly without releasingthe pressure.

24-03-2003
-The jack is fitted with a system which enables it to be folded or
unfolded rapidly.
-T ake the jack from the toolkit and
close it by pressing the ends A.
- Place the jack at one of the loca-tions Eunderneath the vehicle, as
close as possible to the wheel tobe changed. Unfold it by pulling theends A.
- Extend the jack using the wheel-brace 1and the extension 3.
-T ake out a wheel bolt at the top
and fit the centralising tool 2.
- Loosen the wheel bolts and remo-ve the wheel. Fitting a wheel -
Position the wheel using the cen- tralising tool to assist you.
-T ighten the bolts by hand, and
remove the centralising tool.
- Partly tighten the bolts using thewheelbrace.
- Fold the jack and remove it.
- Fully tighten the wheel bolts usingthe wheelbrace.
- Replace the centre trim by pres-sing it with the palm of your hand.
MAINTENANCE OF YOUR 406 COUPE 33
For your safety, always change the wheel:
- on level, stable, non-slipperyground,
- with the handbrake applied,
- with first or reverse gear enga-ged (position Pfor the automatic
gearbox).
Never go underneath a vehiclewhich is supported only by a jack(use a ramp). After changing the wheel - have the tightening of the bolts and the tyre pressure checkedby a PEUGEOT dealer as soonas possible,
- have the punctured tyre repai-red and refit it to the vehicle assoon as possible.

24-03-2003
TOWING A TRAILER,
CARAVAN, BOAT etc.
Only use original PEUGEOT tow bars that have been tested andapproved from the design stage of
your vehicle. The tow bar must be
fitted by a PEUGEOT dealer. Y our vehicle is primarily designed for
transporting people and luggage but
it may also be used for towing a trailer. Driving with a trailer subjects the towing vehicle to more significantstress and its driver must be particu-larly careful. Air density decreases with altitude, thus reducing engine performance.Above 1000 metres, the maximumtowing load must be reduced by 10%and so on for every 1000 metres ofaltitude. Driving advice Distribution of loads:Distribute the load in the trailer so that the heaviest items are as closeas possible to the axle and the noseweight approaches the maximumpermitted without exceeding it. Cooling: T
owing a trailer on a slope increases
the temperature of the coolant. As the fan is electrically controlled, its cooling capacity is not dependenton the engine speed.
On the contrary, use a high gear to lower the engine speed, and reduceyour speed. The maximum towing load on a long slope depends on the gradient andthe outside temperature. In all cases, pay attention to the coolant temperature. If the warning light comes on, stop
the vehicle and switch off the engineas soon as possible. T
yres:
Check the tyre pressures of the tow-
ing vehicle and of the trailer, observ-ing the recommended pressures. Braking: T owing increases the braking dis-
tance. Lights: Check the electrical signalling on the
trailer. Side wind: T ake into acount the increased sen-
sitivity to side wind.
MAINTENANCE OF YOUR 406 COUPE 45

24-03-2003
THE IDENTIFICATION FEATURES OF YOUR 406 COUPE
A. Manufacturer's plate.
B. Model serial number on the bodywork.
C. Paint colour reference.
D. Serial number on the fascia.
E. Tyre pressure label.
Tyres
The tyre pressure label Eon the dri-
ver's door pillar, near the hinges, gives: Ð the wheel and tyre sizes,
Ð the brands of tyres approved by
the manufacturer,
Ð the tyre pressures.
The tyre pressure must be checkedwhen cold, at least once a month. T yre sizes fitted as standard:
Ð 215/55 R 16 V for vehicles fitted with the 2.2 litre 16V and 3 litre24V V6 petrol engines and the2.2 litre 16V HDI diesel engine.
Ð 205/55 R 16 for vehicles fitted withthe 2 litre 16V petrol engine.
Ð winter tyres for all engines:
Michelin Pilot Alpin 205/55 R 16.
TECHNICAL DATA 137