mirror controls Peugeot 406 C Dag 2002 Owner's Manual

10 -Passenger air bag.
11 - Glove box.
12 - Side adjustable heating/ ven- tilation vents and air flow reg-ulation.
13 - Window demisting vent.
14 - Speaker (tweeter) location.
15 - Multi-function display.
16 - Heating/ventilation controls.
17 - Radio.
18 - Gear lever.
19 - Front ashtray.
20 - Rear footwell heating vent.
21 - Lighter. 22 -
Heated seat switches. Coin storage. Passenger air bag disarming switch.
23 - Handbrake.
24 - Cup-holder.
25 - Rear ashtray.
26 - Steering lock and ignition.
27 - Steering wheel adjustment.
28 - Fuse box.
29 - Electronic stability programme (ASR/ESP)
30 - Headlamp height adjustment.
31 - Cruise control.
YOUR 406 COUPE AT A GLANCE
3
1 - Electric mirror controls. Window controls.
2 - Lights and direction indicators stalk.
3 - Driver's air bag.Horn.
4 - Instrument dials.
5 - Radio remote control stalk.
6 - Windscreen wash-wipe stalk.
Trip computer stalk.
7 - Hazard warning lights switch.
8 - Central adjustable heating/ventilation vents and air flowregulation.
9 - Windscreen demistingvents.
01-07-2002

Recalling a memorised position
¥ Door open and ignition off Within ten minutes of switching off
the ignition and opening the door, ashort press on button 1or 2recalls
the memorised position of the seat,then of the exterior mirrors.
¥ Door closed or ignition on:
- keeping the button pressedadjusts the seat and the exteriormirrors. When adjustment is completed a bleep will sound.
YOUR 406 COUPE IN DETAIL 93
Memorising the seat and mirror positions
Two driving positions can be memo- rised.
To memorise:
- place the ignition key in the acces- sories position;
- adjust your seat and mirrors;
- simultaneously press button " M"
and button " 1" for the first driving
position or button " 2" for the
second driving position. When the position has been memorised, you will hear twobleeps. Memorising a new position cancels the previous one. Heated seat controls Press the switch.The temperature is controlled auto-
matically. Pressing a second time stops opera- tion.
01-07-2002

THE KEYS The keys allow you to switch on the ignition and to independently operatethe locks on the doors, the fuel fillercap, the glove box and the passen-ger air bag disarming switch. Central locking From the doors the keys allow you to lock, deadlock and unlock the doorsand the boot, as well as fold back theexterior mirrors. If one of the front doors or the boot is open, central locking is not possible.In this case a bleep indicates lockingby remote control. The remote control performs the same functions at a distance. The remote control LockingPress button Ato lock the vehicle. This is confirmed by fixed lighting of the direction indicators for approxi-mately 2 seconds. Note:
in addition to locking, pressing
button Aautomatically closes the
windows and the sunroof. Deadlocking Deadlocking renders ithe internal and external door controls inopera-tive. Press button Ato deadlock the vehi-
cle. This is confirmed by fixed light- ing of the direction indicators forapproximately two seconds. Note : a long press on button A, in
addition to deadlocking, automatical- ly closes the windows and the sun-roof. Another press on button A, within
five seconds of deadlocking, changes this to normal locking. This is confirmed by fixed ighting of the direction indicators for approxi-mately two seconds, accompaniedby a brief sound of the horn. Unlocking Press button Bto unlock the vehicle.
This is confirmed by rapid flashing of the direction indicators. Note:
avoid handling the button of
your remote control when out of
range of your vehicle. You run therisk of stopping it from working. Itwould then be necessary to repro-gramme the remote control.
YOUR 406 COUPE IN DETAIL
84
ELECTRONIC ENGINE IMMOBILISER This locks the engine management system as soon as the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the codeis recognised and starting is possi-ble. If the system does not function
correctly, an audible signal sounds,
accompanied by a message on the
multi-function display.
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon as possible.
01-07-2002

AUTOMATIC SWITCHING ON OF THE LIGHTS Side lights and dipped beam head- lamps switch on automatically if the
light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories position (1st notch),
 Press the end of the lights stalkfor more than two seconds.
Note: In foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located in the windscreen behind
the mirror. It is used for automaticswitching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multi-function display. Note: Always operate the lighting
controls manually where this is pos- sible. Disarming Disarming of the function is accom- panied by an audible signal. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is however possible to disarm this
function and switch off the lights by:
- manually switching off the lights using the lights stalk,
- switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights comeon). The driver is alerted by the flashingof the ''dipped beam'' warning lighton the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute.
To do this: place the lights stalk in the AUTO
position,
 place the key in the accessories position (first notch),
 press the end of the lights stalk formore than two seconds,
 place the lights stalk in the 0posi-
tion,
 flash the headlamps,
 get out of the car and lock it.
YOUR 406 COUPE IN DETAIL
100
01-07-2002