warning Peugeot 407 2009 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009, Model line: 407, Model: Peugeot 407 2009Pages: 250, PDF Size: 14.81 MB
Page 23 of 250
1INSTRUMENTS and CONTROLS
24
P a r t i c l e e m i s s i o n fi l t e r
saturation warning light
(Diesel engine)
With the engine running, this indicates
t h a t t h e p a r t i c l e e m i s s i o n fi l t e r i s s t a r t -
ing to become saturated (exceptionally
prolonged urban driving type condi-
t i o n s : l o w s p e e d , l o n g t r a f fi c j a m s . . . ) o r
a low diesel additive reservoir level.
I n o r d e r t o r e g e n e r a t e t h e fi l t e r , y o u a r e
advised to drive, as soon as possible
w h e n t h e t r a f fi c c o n d i t i o n s p e r m i t , a t a
speed of 40 mph (60 km/h) or above
f o r a t l e a s t fi v e m i n u t e s ( u n t i l t h e w a r n -
ing light is switched off).
If the warning light remains on, contact
a PEUGEOT dealer.
Following prolonged use of the vehi-
cle at very low speeds or at idle, you
may, exceptionally, notice an emission
of water vapour at the exhaust dur-
ing acceleration. This does not affect
the performance of the vehicle or the
environment.
Service warning light
This is displayed to indicate an engine
management system fault.
Contact a PEUGEOT dealer as soon
as possible. Automatic gearbox fault
warning light
This indicates an automatic gearbox
fault.
The gearbox will operate in down-
grade mode, locked in 3rd gear.
Never force the selector lever.
Consult a PEUGEOT dealer.
Electronically controlled
suspension fault warning
light
This indicates an electronically con-
trolled suspension malfunction.
Select automatic operation and con-
tact a PEUGEOT dealer as soon as
possible. Obstacle proximity
detection system warning
light
In reverse gear, this indicates an ob-
stacle proximity detection system
fault.
Consult a PEUGEOT dealer. Electronically controlled
suspension indicator lights
This comes on when the SPORT func-
tion is activated. This comes on when the
SPORT function is deactivated.
Automatic switching on of
the lights indicator light
Automatic switching on
of the lights deactivation
indicator light
Automatic wipers indicator
light
Automatic wipers
deactivation indicator light
This comes on when the AUTO func-
tion is activated.
This comes on when the AUTO func-
tion is deactivated.
This comes on when the AUTO func-
tion is activated.
This comes on when the AUTO func-
tion is deactivated.
Page 29 of 250
1INSTRUMENTS and CONTROLS
29
Range
(km or miles)
Current consumption
(l/100 or km/l or mpg)
This is the average quantity of fuel
consumed during the last few seconds.
This shows the distance that can still
be covered with the fuel remaining
in the tank in accordance with the
average consumption over the last
few miles (kilometres).
Distance remaining to be
travelled (km or miles)
Average speed
(km/h or mph) ''TRIP'' (Route) menu
Press the
''MENU'' button to gain access
to the general menu.
Select the ''Trip computer'' or ''Vehicle
diagnostics'' application using the navi-
g a t o r , t h e n c o n fi r m o r p r e s s t h e ''MODE''
button until you gain access to the trip
c o m p u t e r s c r e e n , t h e n c o n fi r m ''OK'' .
The ''Trip computer'' or ''Vehicle diagnostics''
menu offers various options:
- Warnings log,
- Status of the functions,
- Inputting of the distance to be
travelled.
Average consumption
(l/100 or km/l or mpg)
Distance travelled
(km or miles) Warnings log
This summarises the active warning
messages, displaying them on the
multifunction display in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining
(km or miles)
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled.
T h i s fi g u r e m a y i n c r e a s e i f
there is a change in the style
of driving or the road surface,
p r o d u c i n g a s i g n i fi c a n t d r o p i n
current consumption.
When the range is less than 20 miles
(30 km), four segments are displayed.
A f t e r fi l l i n g w i t h f u e l , t h e r a n g e i s
displayed when it exceeds 62 miles
(100 km). If horizontal segments are dis-
played for long periods instead
of digits, contact a dealer.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
This is the distance remaining to
the destination, either calculated at
any time by the navigation system if
guidance is activated or entered by
the user, minus the distance covered
since the distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last set to zero.
This indicates the distance travelled
since the computer was last set to zero. Access via the general menu
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
Page 30 of 250
2MULTIFUNCTION DISPLAYS
30
MONOCHROME DISPLAY C AND COLOUR DISPLAY C (WITH PC SOUND)
This displays the following information:
- the time,
- the date,
- the exterior temperature (the value d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k o f
ice),
- t h e a c c e s s e s c h e c k ,
- the vehicle function status messages, displayed temporarily,
- the warning messages,
- the audio functions,
- the trip computer information,
- the vehicle parameters,
- the air conditioning parameters,
- the choice of language. General menu
D e fi n e t h e v e h i c l e p a r a m e t e r s
Permits the activation or deactivation
of certain driving and comfort ele-
ments.
Example: Automatic switching on of
the lights.
Press the "MENU" button to gain ac-
cess to the general menu and select
one of the following functions: Audio
Functions, Trip Computer, Person-
a l i s a t i o n / C o n fi g u r a t i o n a n d A i r C o n d i -
tioning.
Example: display selected on "Audio
Functions".
The " P e r s o n a l i s a t i o n - C o n fi g u r a t i o n "
menu provides access to successive
c o n fi r m a t i o n w i n d o w s .
M a n a g e m e n t o f t h e d i s p l a y s
The "AUDIO" , "TRIP" and "CLIM"
b u t t o n s o n t h e a u d i o e q u i p m e n t k e y -
pad permit displaying in the main win-
dow (on the right).
Example: TRIP C h o i c e o f l a n g u a g e
German, Spanish, French, English,
I t a l i a n , D u t c h , T u r k i s h , P o r t u g u e s e
and Brazilian Portuguese.
Page 32 of 250
2MULTIFUNCTION DISPLAYS
32
D i s p l a y
This menu allows you to set the bright-
ness of the display, the display colour
scheme and the colour of the map
(day/night and auto mode).
V e h i c l e
This menu permits the activation or
deactivation of certain driving and
comfort systems:
- air conditioning (A/C),
- vehicle information,
- access to the vehicle,
- driving assistance,
- l i g h t i n g c o n fi g u r a t i o n ,
- comfort lighting.
U n i t s
This menu permits selection of the
units: temperature (°C or °F) and
c o n s u m p t i o n ( k m / l , l / 1 0 0 , m i l e s a n d
mpg).
S y s t e m
This menu permits restoring of the
f a c t o r y c o n fi g u r a t i o n , d i s p l a y i n g o f t h e
software version and activation of the
scrolling text. F o r s a f e t y r e a s o n s , c o n fi g u r a -
tion of the multifunction dis-
plays by the driver must be
carried out when stationary. COLOUR DISPLAY(WITH PC NAV) "SETUP" menu
Press the SETUP button to gain access
to the "SETUP" menu. This provides
access to the following functions:
- System language,
- Date & Time,
- Display,
- Vehicle,
- Units,
- System.
S y s t e m l a n g u a g e
This menu allows you to select
the language used by the display:
German, English, Spanish, French,
Italian, Dutch, Polish, Portuguese.
D a t e & T i m e
This menu allows you to set the date
and time, the format of the date and
the format of the time (refer to the "Au-
dio and Telematics" section).
This displays the following informa-
tion:
- the time,
- the date,
- the exterior temperature (the value
d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k o f
ice),
- t h e a c c e s s e s c h e c k ,
- the vehicle function status messag- es, displayed temporarily,
- the warning messages,
- the audio functions,
- the trip computer information,
- the air conditioning parameters,
- the satellite navigation system infor- mation.
Page 33 of 250
2MULTIFUNCTION DISPLAYS
33
HIGH DEFINITION COLOUR DISPLAY (WITH PC COM)
This displays the following information:
- the time,
- the date,
- the exterior temperature (the value d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k o f
ice),
- t h e a c c e s s e s c h e c k ,
- the vehicle function status messages, displayed temporarily,
- the warning messages,
- the audio functions,
- the trip computer information,
- the air conditioning parameters,
- the satellite navigation system infor- mation.
General menu D i s p l a y c o n fi g u r a t i o n
Press the "MENU" button to gain ac-
cess to the general menu and select
one of the following functions: Naviga-
t i o n - G u i d a n c e , M a p , T r a f fi c I n f o r m a t i o n ,
A u d i o F u n c t i o n s , T e l e m a t i c s , C o n fi g u r a -
tion, Video, Vehicle Diagnostics and Air
Conditioning. - Choose colour,
- Adjust brightness,
- Adjust date and time,
- Choose units.
D e fi n e t h e v e h i c l e p a r a m e t e r s
Permits the activation or deactivation of
certain driving and comfort elements:
- p e r m a n e n t l o c k i n g o f t h e b o o t o n
the 407 Saloon,
- automatic switching on of the lights,
- automatic "follow-me-home" lighting,
- automatic rear wiping on engaging reverse gear on the 407 SW.
The " C o n fi g u r a t i o n " menu provides
access to the following functions:
- D i s p l a y c o n fi g u r a t i o n ,
- Sound,
- Choice of language,
- D e fi n e t h e v e h i c l e p a r a m e t e r s .
You can connect video equipment
(camcorder, digital camera, ...) to the
t h r e e v i d e o s o c k e t s , l o c a t e d i n t h e
glove box.
Video display is only possible when
stationary.
Select the Video menu from the general
menu:
- "Activate video mode" to activate/deactivate the video,
- "Video parameters" to set the dis- play format, the brightness, the con-
trast and the colours.
P r e s s t h e " E S C " o r " D A R K " b u t t o n t o
exit from video mode.
P r e s s t h e " S O U R C E " b u t t o n s e v e r a l
times in succession to select an audio
source other than that of the video. VIDEO MENU (WITH PC COM)
Page 74 of 250
4ACCESS
66
ALARM When the alarm is triggered, the siren
sounds and the direction indicator lights
fl a s h f o r a p p r o x i m a t e l y t h i r t y s e c o n d s .
After triggering, the alarm remains set,
ten times in succession.
On the eleventh time it will become
inactive again, until the next cycle of
disarming then setting of the alarm.
Warning: if button A indicator light
fl a s h e s r a p i d l y , t h e a l a r m h a s b e e n
triggered while you were away from
your vehicle.
Note: if the alarm has been triggered
i n y o u r a b s e n c e , t h i s fl a s h i n g s t o p s
when the ignition is switched on. Remote control failure,
alarm set
Unlock the doors with the key and
o p e n t h e d o o r . T h e a l a r m i s t r i g -
gered.
Switch on the ignition. The alarm is
disarmed.
* According to country.
Setting the alarm
Switch off the ignition and get out
of the vehicle.
S e t t h e a l a r m , b y l o c k i n g o r d e a d -
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once per second).
If you wish to lock or deadlock your
vehicle without setting the alarm, lock
it (one turn of the key) or deadlock it
( a s e c o n d t u r n w i t h i n fi v e s e c o n d s
maximum) using the lock. Disarming
Unlock the vehicle with the remote
control key.
The alarm is disarmed, indicator light
A
goes out when the ignition is switched on
(unless the alarm has been triggered).
To set the alarm with exterior
protection only
If, while you are away from the vehicle,
you wish to leave a window partially
open or a pet inside the vehicle, you
should choose exterior protection only.
Switch off the ignition,
I n t h e n e x t t e n s e c o n d s , p r e s s b u t -
ton A until the indicator light is on
continuously,
Get out of the vehicle,
S e t t h e a l a r m b y l o c k i n g o r d e a d -
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once a second). Incorrect operation
When the ignition is switched on, if
button
A lights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have
the system checked.
Automatic activation *
The alarm is activated automatically
two minutes after the last closure of a
door or the boot.
In order to avoid accidental triggering
of the alarm when a door or the boot
is opened, it is essential to press the
unlocking button on the remote control
again.
When the alarm is set, if a door,
the tailgate or the bonnet is
not closed correctly, the siren
i s t r i g g e r e d b r i e fl y . I f t h e v e h i -
cle is closed correctly within the next
45 seconds, the alarm is set. In all cases,
the alarm is set after 45 seconds.
This provides two types of surveillance:
-
exterior protection: it sounds if
a door, the boot or the bonnet is
opened. - interior protection: it sounds if the
v o l u m e i n s i d e t h e p a s s e n g e r c o m p a r t -
ment changes (breaking of a window
or a movement inside the vehicle).
Page 78 of 250
4ACCESS
69
"Rear screen open" warning
When the engine is running, if the
rear screen is not fully closed, you are
w a r n e d b y a m e s s a g e o n t h e m u l t i -
function display.
When the vehicle is moving (speed
greater than 6 mph (10 km/h)), if the
rear screen is not fully closed, you are
w a r n e d b y a n a u d i b l e s i g n a l , a m e s -
sage on the multifunction display and
lighting of the service warning light. Tailgate release
T h i s e n a b l e s t h e t a i l g a t e t o b e u n -
locked in the event of a central locking
fault.
- F o l d b a c k t h e r e a r s e a t s t o g a i n
access to the lock from inside the
boot,
- I n s e r t a s m a l l s c r e w d r i v e r i n t o h o l e A
of the lock to unlock the tailgate.
Page 81 of 250
4ACCESS
72
FILLING WITH FUEL
The ignition must be switched
o f f a n d t h e v e h i c l e m u s t b e u n -
l o c k e d w h e n fi l l i n g w i t h f u e l . When this warning light comes
on in certain driving conditions
and depending on the engine,
the distance which can be
travelled with the fuel remaining may
be less than 30 miles (50 kilometres).
Note: should you run out of fuel, you
must add at least 6 litres.
Operating fault
A fuel gauge fault is indicated by the
fuel level indicator needle returning to
zero.
Consult a PEUGEOT dealer.
Fuel warning
A l a b e l a f fi x e d t o t h e i n s i d e o f t h e f u e l
fi l l e r fl a p i n d i c a t e s w h i c h t y p e o f f u e l
to use.
W h e n y o u fi l l y o u r t a n k , d o n o t c o n -
t i n u e a f t e r t h e t h i r d c u t - o f f o f t h e p u m p .
T h i s c o u l d c a u s e y o u r v e h i c l e t o m a l -
function.
T h e c a p a c i t y o f t h e t a n k i s a p p r o x i -
mately 67 litres.
A f t e r fi l l i n g t h e t a n k , s c r e w o n t h e
c a p a n d c l o s e t h e f u e l fi l l e r fl a p .
O p e n t h e f u e l fi l l e r fl a p .
Turn the cap to the left.
Remove the cap and hang the end
on the hook located on the inside
o f t h e fl a p . BioFlex engine
A Flex vehicle has been designed to
run on unleaded petrol (RON 95 or
RON 98) or ethanol (this is a mixture
c o n t a i n i n g 8 5 % e t h a n o l a n d 1 5 % u n -
leaded petrol, called E85).
So, regardless of the quantity of fuel
r e m a i n i n g i n y o u r t a n k a n d i r r e s p e c -
tive of its type (RON 95/RON 98, E85
o r a m i x t u r e o f t h e t w o ) , y o u c a n fi l l
your tank at any time with unleaded
petrol (RON 95 or RON 98) or ethanol
(E85).
There is no problem driving on unleaded
petrol only with this vehicle.
In winter conditions, starting the
e n g i n e f r o m c o l d m a y s o m e -
t i m e s p r o v e d i f fi c u l t . D u r i n g
these very cold periods you
are advised to favour unleaded petrol to
guarantee optimum starting conditions.
Page 83 of 250
5
74
Automatic switching on of the lights
T h e d i p p e d b e a m h e a d l a m p s s w i t c h
o n a u t o m a t i c a l l y i f t h e l i g h t i s p o o r a n d
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
the brightness sensor can detect suf-
fi c i e n t l i g h t . T h e l i g h t s w i l l n o t c o m e o n
a u t o m a t i c a l l y .
I f n e c e s s a r y , y o u m u s t s w i t c h t h e
d i p p e d h e a d l a m p s o n m a n u a l l y . Activation Manual "Follow-me-home"
lighting
When you leave your vehicle, the side
l i g h t s a n d d i p p e d h e a d l a m p s c a n b e
left on for a few seconds.
When the function is activated,
t h e i n d i c a t o r l i g h t c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l d i s p l a y .
T o d i s a r m o r a c t i v a t e t h e
function, pass via the
" P e r s o n a l i s a t i o n - c o n -
fi g u r a t i o n " m e n u o n y o u r
m u l t i f u n c t i o n d i s p l a y .
F o r s a f e t y r e a s o n s , a c t i v a t i o n /
d e a c t i v a t i o n o f t h e " A u t o m a t i c
switching on of the lights"
f u n c t i o n v i a t h e m e n u m u s t b e
carried out when stationary. To deactivate or activate the
" A u t o m a t i c f o l l o w - m e - h o m e
lighting" function, pass via the
" P e r s o n a l i s a t i o n - c o n fi g u -
ration" m e n u o n y o u r m u l t i -
function screen.
T h e d u r a t i o n o f t i m i n g c a n b e
set via the "Personalisation-
c o n fi g u r a t i o n " m e n u o f y o u r
m u l t i f u n c t i o n d i s p l a y .
Automatic "Follow-me-home"
lighting
When you leave your vehicle
with the
automatic switching on of the lights
activated, the side lights and dipped
h e a d l a m p s r e m a i n o n f o r t h e d u r a t i o n
selected after the ignition is switched
off.
Disarming
W h e n t h e f u n c t i o n i s d i s a r m e d ,
t h e i n d i c a t o r l i g h t c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l d i s p l a y .
D o n o t c o v e r t h e s u n s h i n e /
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
c o n d i t i o n i n g a n d f o r t h e a u t o m a t i c
switching on of the lights.
If the sunshine/brightness sensor
does not function correctly, the side
l i g h t s a n d d i p p e d h e a d l a m p s c o m e o n .
Consult a PEUGEOT dealer. Activation:
switch off the engine,
" fl a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Page 84 of 250
5
74
Automatic switching on of the lights
T h e d i p p e d b e a m h e a d l a m p s s w i t c h
o n a u t o m a t i c a l l y i f t h e l i g h t i s p o o r a n d
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
the brightness sensor can detect suf-
fi c i e n t l i g h t . T h e l i g h t s w i l l n o t c o m e o n
a u t o m a t i c a l l y .
I f n e c e s s a r y , y o u m u s t s w i t c h t h e
d i p p e d h e a d l a m p s o n m a n u a l l y . Activation Manual "Follow-me-home"
lighting
When you leave your vehicle, the side
l i g h t s a n d d i p p e d h e a d l a m p s c a n b e
left on for a few seconds.
When the function is activated,
t h e i n d i c a t o r l i g h t c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l d i s p l a y .
T o d i s a r m o r a c t i v a t e t h e
function, pass via the
" P e r s o n a l i s a t i o n - c o n -
fi g u r a t i o n " m e n u o n y o u r
m u l t i f u n c t i o n d i s p l a y .
F o r s a f e t y r e a s o n s , a c t i v a t i o n /
d e a c t i v a t i o n o f t h e " A u t o m a t i c
switching on of the lights"
f u n c t i o n v i a t h e m e n u m u s t b e
carried out when stationary. To deactivate or activate the
" A u t o m a t i c f o l l o w - m e - h o m e
lighting" function, pass via the
" P e r s o n a l i s a t i o n - c o n fi g u -
ration" m e n u o n y o u r m u l t i -
function screen.
T h e d u r a t i o n o f t i m i n g c a n b e
set via the "Personalisation-
c o n fi g u r a t i o n " m e n u o f y o u r
m u l t i f u n c t i o n d i s p l a y .
Automatic "Follow-me-home"
lighting
When you leave your vehicle
with the
automatic switching on of the lights
activated, the side lights and dipped
h e a d l a m p s r e m a i n o n f o r t h e d u r a t i o n
selected after the ignition is switched
off.
Disarming
W h e n t h e f u n c t i o n i s d i s a r m e d ,
t h e i n d i c a t o r l i g h t c o m e s o n o n t h e
5 - d i a l i n s t r u m e n t p a n e l d i s p l a y .
D o n o t c o v e r t h e s u n s h i n e /
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
c o n d i t i o n i n g a n d f o r t h e a u t o m a t i c
switching on of the lights.
If the sunshine/brightness sensor
does not function correctly, the side
l i g h t s a n d d i p p e d h e a d l a m p s c o m e o n .
Consult a PEUGEOT dealer. Activation:
switch off the engine,
" fl a s h " t h e h e a d l a m p s ,
get out of the vehicle and lock it.