change wheel Peugeot 407 2009 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009, Model line: 407, Model: Peugeot 407 2009Pages: 250, PDF Size: 14.81 MB
Page 21 of 250
1INSTRUMENTS and CONTROLS
22
Battery charge warning
light
When the engine is running, this in-
dicates a charging circuit malfunction
(battery terminals, alternator belt).
Consult a PEUGEOT dealer. T y r e u n d e r - i n fl a t i o n w a r n i n g
light
This indicates that the tyre pressure is
too low.
A message on the multifunction display
indicates the wheel(s) concerned.
R e f e r t o t h e i n f o r m a t i o n l a b e l a f fi x e d
to the central pillar of the driver's door.
For your safety, check the tyre pres-
sures as soon as possible.
Electronic stability control system
(ESP) warning lights Activation warning light
Operation warning light
Deactivation warning light
Malfunction warning light
Power steering warning
light
This indicates a power steering fault.
It is linked with the STOP warning
light.
Consult a PEUGEOT dealer. Handbrake warning light
This indicates that the handbrake is
still applied or has not been released
correctly.
It is linked with the braking system
warning light. Low wash-wipe and
h e a d l a m p w a s h fl u i d l e v e l
warning light
When the wipers are switched on, this
i n d i c a t e s t h a t t h e fl u i d l e v e l i s t o o l o w .
Fill the wash-wipe and headlamp wash
fl u i d r e s e r v o i r .
Engine oil level warning
light
This indicates a critical engine oil level
(too low).
WARNING LIGHTS ON THE INSTRUMENT PANEL DISPLAY
These warning lights are displayed on
the instrument panel display.
STOP warning light
When this is displayed alone, it indi-
cates a power steering fault.
It comes on linked with the engine oil
pressure, coolant temperature, brak-
ing system or punctured tyre warning
lights.
Stop immediately.
Consult a PEUGEOT dealer.
Punctured tyre warning light
This indicates that one or more punc-
tured tyres have been detected.
A message on the multifunction display
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
light.
Stop immediately.
Consult a PEUGEOT dealer.
Stop immediately.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Page 111 of 250
8DRIVING
93
HANDBRAKE 6-SPEED MANUAL GEARBOX
To release
Pull the handle and press the button to
release the handbrake.
To apply
When parking on a slope, turn the
wheels towards the kerb and apply the
handbrake.
Reverse
To change to reverse gear, lift the ring
under the gear lever knob and push
the gear lever to the left then to the
front.
Reverse gear can only be engaged
when the vehicle is stationary with
the engine idling.
Page 119 of 250
8DRIVING
101
TYRE UNDER-INFLATION DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction.
Flat tyre Instrument panel display
warning light.
This is accompanied by the audible signal
and the message on the multi-function
display locating the wheel concerned.
If this warning light comes on, have
the tyre pressure checked as soon as
possible.
Puncture
This warning light, accompanied by
the audible signal and the message on
the multi-function display locating the
wheel concerned, is followed by illumi-
nation of the "STOP" warning light. Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
t u r e d o r v e r y d e fl a t e d t y r e ) , a n d h a v e
the tyre pressure checked as soon as
possible.
Sensor(s) not detected or faulty
Instrument panel display
warning light. All repairs and changing of
t y r e s o n a w h e e l fi t t e d w i t h t h i s
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install a
wheel which is not detected by your
vehicle, you must have the system
reinitialised by a PEUGEOT dealer.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n s y s -
tem is an aid to driving which does not
replace the need for the driver to be
vigilant or to drive responsibly.
This system does not eliminate
the need to have the tyre pressure
checked regularly (see manufacturer's
label on the door pillar) to ensure that
the optimum dynamic performance
of the vehicle is maintained and pre-
vent premature wear of the tyres, par-
ticularly in arduous driving conditions
(heavy load, high speed).
The tyre pressures must be checked
cold, at least once a month. Remem-
ber to check the pressure of the spare
wheel.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n s y s -
tem may experience temporary inter-
ference due to radioelectric emissions
on a frequency close to that used by
the system.
Note : this message is also
displayed when one of the
wheels is away from the ve-
hicle (being repaired) or when
one or more wheels without a
s e n s o r a r e fi t t e d .
Instrument panel display
warning light.
This is accompanied by the audible
signal and the message on the multi-
function display which indicates that
u n d e r - i n fl a t i o n d e t e c t i o n i s a b s e n t
from one (or several) wheel(s) or that
there is a fault in the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).
Page 129 of 250
1010PRACTICAL INFORMATION
112
CHANGING A WHEEL
Tools available
The following tools are located in
the holder in the centre of the spare
wheel:
1. Wheelbrace.
Permits removal of the wheel trim and removal of the wheel securing
bolts.
2. Jack with integrated handle.
Permits raising of the vehicle.
3. Removable towing eye.
See corresponding section.
4. Bolt cover tool.
Permits removal of the bolt protectors (covers) on alloy wheels. Removal
For vehicles with steel wheels,
detach the trim using the wheel-
brace 1 pulling at the valve pas-
sage hole.
For vehicles with alloy wheels,
remove the covers using tool 4 .
Loosen the wheel bolts.
Take the jack from the tool kit.
Place the jack 2 in one of the four
locations underneath the vehicle
(the nearest one to the wheel to be
changed).
Extend the jack 2 until its base is in
contact with the ground.
Unscrew the bolts and remove the
wheel.
Access to the spare wheel and the
jack in the boot
L i f t t h e fl o o r u s i n g t h e l i f t i n g h a n d l e .
Secure the handle behind the boot
seal. Never go underneath a vehicle
which is supported only by a
jack.
Park the vehicle on level, stable
and non-slippery ground.
Apply the handbrake, switch off the
i g n i t i o n a n d e n g a g e fi r s t o r r e v e r s e
gear (position P for the automatic
gearbox).
Page 130 of 250
1010PRACTICAL INFORMATION
113
Fitting a wheel
Position the wheel.
Tighten the bolts by hand.
Partly tighten the bolts using the
wheelbrace.
Fold the jack 2 and remove it.
Fully tighten the bolts using the
wheelbrace 1 .
For vehicles with steel wheels,
r e fi t t h e w h e e l t r i m s t a r t i n g b y p l a c -
ing its notch facing the valve and
press with the palm of the hand.
F o r v e h i c l e s w i t h a l l o y w h e e l s , r e fi t
the covers.
Put the tool holder back in position.
T h i s h e l p s t o k e e p t h e b o o t fl o o r i n
its correct position, to prevent any
d e f o r m a t i o n o f t h e fl o o r w h e n l o a d e d .
Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact. Punctured tyre warning
light
Information on the instrument
panel:
Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the handbrake applied,
-
w i t h fi r s t o r r e v e r s e g e a r e n g a g e d ( p o -
sition P for the automatic gearbox),
- never go underneath a vehicle
which is supported only by a jack. T y r e u n d e r - i n fl a t i o n d e t e c t i o n
system warning light
T h e s e o r i g i n a l w h e e l s a r e fi t t e d w i t h a
pressure sensor (see paragraph "Tyre
u n d e r - i n fl a t i o n d e t e c t i o n " ) . T h e a l a r m
which detects the removal or absence
o f a w h e e l fi t t e d w i t h t h e i n d i c a t o r
sensor signals the anomaly. Have
the wheel repaired and checked by a
PEUGEOT dealer.
After changing the wheel:
- have the tightening of the bolts and
the tyre pressure of the spare wheel
checked as soon as possible.
- have the punctured wheel repaired a n d r e fi t i t t o t h e v e h i c l e a s s o o n a s
possible.
- have the spare wheel checked and replace it in its boot recess.
Recommendations when using the
temporary spare wheel *
Your vehicle may be equipped with a
spare wheel with a different rim to that
of the standard wheel.
After use, replace it as soon as possible.
Follow the recommendations below
to avoid any alteration in vehicle han-
dling:
-
do not drive above 50 mph (80 km/h) ,
- d o n o t fi t a w h e e l t r i m ,
- drive carefully,
- c h e c k t h e i n fl a t i o n p r e s s u r e i n d i - cated on the label.
* According to version and country.
Page 133 of 250
1010PRACTICAL INFORMATION
115
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Main beam headlamps: H7-55 W.
Remove the protective cover cor-
responding to the faulty bulb.
Disconnect the connector.
Press the end of the securing clips
to free the bulb. Change the bulb.
W h e n fi t t i n g t h e n e w b u l b , e n s u r e t h a t
the direction notches are positioned
correctly and the securing clips are
fi x e d p r o p e r l y .
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
4 -
Direction indicators:
PY 21 W (amber).
Turn the bulb holder a quarter turn
and remove it.
Change the bulb.
WARNING: RISK OF
ELECTROCUTION
Front lights
In the engine compartment, remove
the cover secured by one or two but-
t e r fl y s c r e w s , a p l a s t i c r e t a i n e r c l i p a n d
two quarter turn screws.
1 - Dipped beam headlamps:
H1-55 W or D2S-35 W xenon bulb.
Xenon bulbs must be replaced by a
PEUGEOT dealer. Amber coloured bulbs (direction
indicators and side repeaters)
must be replaced with bulbs
o f i d e n t i c a l s p e c i fi c a t i o n a n d
colour.
5 - Front fog lamps: H11 - 55 W.
Turn the wheels to full lock.
A c c e s s t o t h e b u l b i s v i a t h e fl a p i n t h e
f r o n t m u d fl a p .
Consult a PEUGEOT dealer.
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y c a r -
bonate glass with a protective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or sol-
vent product.
E n s u r e t h a t t h e l i q u i d u s e d t o fi l l t h e
wash-wipe and headlamp wash reser-
voir is of good quality.
High pressure washing :
when using a high pressure
washer on stubborn dirt, do
not persist on the headlamps,
the lights and their periphery to avoid
damaging their coating and their seal.
In certain climatic conditions (low tem-
perature, humidity), condensation on
the inside surface of the headlamp
glass and rear lights glass is normal;
it disappears a few minutes after the
lights are switched on.
3 - Side lights: W 5 W.
Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.
Put the connector back in place.
Reconnect the connector.
R e fi t t h e p r o t e c t i v e c o v e r .
Page 134 of 250
1010PRACTICAL INFORMATION
116
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.
Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.
Press on the two tabs located at
the rear, near the rear screen.
Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.
S c r e w o n t h e l i g h t fi x i n g n u t s i n -
side the boot using the towing eye,
i f n e c e s s a r y . W h e n r e fi t t i n g , e n -
sure that the light is positioned and
fi x e d c o r r e c t l y .
Reconnect the connector.
Number plate lights:
W 5 W.
Remove the transparent cover using
a screwdriver blade.
Change the faulty bulb.
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi c a t i o n a n d c o l o u r .
1. Direction indicators:
PY 21 W (amber).
2. Reversing lights: P21 W.
3. Fog lamps/side lights:
P21/4 W.
4. Side lights: P21/4 W.
5. Brake lights/side lights: P21/4 W.
Disconnect the connector.
U n s c r e w t h e l i g h t fi x i n g n u t s i n -
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.
Remove the seal.
Unclip the bulb holder moving
aside the 5 tabs.
Unscrew the bulb and change it.
Lock the bulb holder in place.
Reposition the seal.
Page 135 of 250
1010PRACTICAL INFORMATION
116
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.
Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.
Press on the two tabs located at
the rear, near the rear screen.
Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.
S c r e w o n t h e l i g h t fi x i n g n u t s i n -
side the boot using the towing eye,
i f n e c e s s a r y . W h e n r e fi t t i n g , e n -
sure that the light is positioned and
fi x e d c o r r e c t l y .
Reconnect the connector.
Number plate lights:
W 5 W.
Remove the transparent cover using
a screwdriver blade.
Change the faulty bulb.
Push the repeater forwards or
backwards and release it.
Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi c a t i o n a n d c o l o u r .
1. Direction indicators:
PY 21 W (amber).
2. Reversing lights: P21 W.
3. Fog lamps/side lights:
P21/4 W.
4. Side lights: P21/4 W.
5. Brake lights/side lights: P21/4 W.
Disconnect the connector.
U n s c r e w t h e l i g h t fi x i n g n u t s i n -
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.
Remove the seal.
Unclip the bulb holder moving
aside the 5 tabs.
Unscrew the bulb and change it.
Lock the bulb holder in place.
Reposition the seal.
Page 136 of 250
1010PRACTICAL INFORMATION
117
CHANGING A REAR BULB (407 SW)
Left and right fog lamps:
P21 W.
Carefully unclip the tailgate interior
trim.
Detach the sealing sheet located
behind the light concerned.
Remove the bulb holder turning it a
quarter of a turn.
Change the faulty bulb.
W h e n r e fi t t i n g , e n s u r e t h a t t h e b u l b i s
positioned correctly in the bulb holder.
Unclip the light (2 clips).
Disconnect the connector and re-
move the light.
Unclip the bulb holder moving
aside the 4 tabs.
Unscrew the bulb and change it.
Reconnect the connector.
Lock the bulb holder in place.
W h e n r e fi t t i n g i t , e n s u r e t h a t t h e
lamp is correctly positioned and
secured, reclipping the rear part
then the front part.
Number plate lights:
W 5 W.
Insert a thin screwdriver in one of
the exterior holes of the transpar-
ent cover.
Push it towards the outside to un-
clip it.
Remove the transparent cover.
Change the faulty bulb. Third brake light (diodes)
All work on the diode lights must be
carried out by a PEUGEOT dealer.
Wing lights
1. Brake lights/side lights:
P21/5 W.
2. Reversing lights:
P21 W.
3. Direction indicators:
P21 W.
These three bulbs are changed by
removing the light.
Remove the corresponding boot
s i d e fl a p t o g a i n a c c e s s t o t h e
light.
R e m o v e t h e l i g h t fi x i n g n u t i n s i d e
the boot.
Note: if necessary, use the wheelbrace
to remove the nuts. In some climatic conditions
(e.g. low temperature or hu-
midity), the presence of misting
on the internal surface of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
Page 150 of 250
1010PRACTICAL INFORMATION
128
ACCESSORIES FOR YOUR 407
A wide range of accessories recom-
mended by PEUGEOT and original
parts are offered by the Network.
They all benefit from PEUGEOT recommendation.
These accessories and parts, having
been tested and approved for reliability
and safety, are all adapted to your
PEUGEOT vehicle.
The product range offered by PEUGEOT Accessories is structured
around 5 categories: PROTECTION -
TOURING - IN-CAR TECHNOLOGY -
STYLING - UNIVERSAL. Anti-theft alarm, parking as-
sistance, engraved windows,
w h e e l a n t i - t h e f t d e v i c e s , fi r s t
aid kit, warning triangle, high
visibility safety jacket, snow
chains, anti-skid covers, dog
guard, etc.
"Protection": Seat covers compatible with
side air bags, mats, boot
tray.
For leisure pursuits: roof bars, transportation acces-
sories (bicycle carrier, ski
carrier), roof box, child seats and
booster cushions, rear screen blind,
audio/telephone console, side blinds,
cool box.
T r a i l e r t o w b a r w h i c h m u s t b e fi t t e d b y
the PEUGEOT Network.
"Touring":
Telephone, hands-free kits,
satellite navigation, CD changer, multimedia, connec-
tion for portable MP3 player
(in the glove box), USB Box.
"In-Car Technology": Alloy wheels, wheel trims,
spoiler, leather steering wheel,
styling strips, door spoilers,
stainless steel sill protectors.
"Styling":
W i n d s c r e e n w a s h fl u i d , i n t e -
rior and exterior cleaning and
maintenance products.
"Universal":
T h e fi t t i n g o f e l e c t r i c a l e q u i p m e n t or accessories which are not
recommended by PEUGEOT
may result in a failure of your
vehicle's electronic system.
P l e a s e n o t e t h i s s p e c i fi c w a r n i n g . Y o u
are advised to contact a representa-
tive of the Marque to be shown the
range of recommended equipment
and accessories.
Note
To avoid any jamming under the pedals:
- ensure that the mat is positioned
and secured correctly,
- never place one mat on top of another.
Depending on the country in
which the vehicle is sold, it
is compulsory to have a high
visibility safety jacket, warning
triangle and spare bulbs available in the vehicle.
Installation of radiocommunication
transmitters
It is advisable to contact a representa-
tive of the PEUGEOT marque before
installing accessory radiocommunica-
tion transmitters with external aerial
on your vehicle. The PEUGEOT Network will inform
y o u o f t h e s p e c i fi c a t i o n s ( f r e q u e n c y
waveband, maximum output power,
a e r i a l p o s i t i o n , s p e c i fi c i n s t a l l a t i o n
conditions) of the transmitters which
c a n b e fi t t e d , i n a c c o r d a n c e w i t h t h e
Motor Vehicle Electromagnetic Com-
patibility Directive (2004/104/EC).
407 SW: you can obtain "Van" con-
version kits to convert from a private
vehicle to a van.