oil Peugeot 407 2009 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009, Model line: 407, Model: Peugeot 407 2009Pages: 250, PDF Size: 14.81 MB
Page 12 of 250
FAMILIARISATION
Instrument panel
A. When the ignition is on, the fuel
gauge needle should rise.
B. When the engine is running, its as-
sociated low level warning light
should switch off.
C. When the ignition is on, the oil level
indicator should display "OIL OK"
for a few seconds.
If the levels are not correct, top up the
level which is low. Lighting of the indicator light indicates the
status of the corresponding function.
When the ignition is on, the orange and
red warning lights come on.
When the engine is running, these
warning lights should switch off.
If any warning light remains on, refer to
the page concerned.
18
20
103
A. Audible front/rear parking
assistance off.
B. Central locking.
C. Interior protection alarm
off.
D. Hazard warning lights.
E. Selection of the electroni-
cally controlled suspen-
sion.
F. Electronic stability pro-
gramme ESP off.
63
66
85
96
85
Warning lights Controls bar
Page 16 of 250
1INSTRUMENTS and CONTROLS
19
1. Coolant temperature indicator dial.
2. Lights on indicators:
dipped headlamps.
main beam headlamps.
front fog lamps.
rear fog lamps.
3. Rev counter dial.
4. Warning lights:
seat belts not fastened
in the front.
fuel level.
left direction indicator.
5. Fuel level indicator dial.
PETROL-DIESEL MANUAL AND AUTOMATIC GEARBOX INSTRUMENT PANELS
10. CHECK and trip recorder zero
reset and service display button.
11. Instrument panel display:
Total distance recorder.
Trip recorder.
Automatic gearbox lever position
indicator.
Cruise control/speed limiter
reference value.
Service indicator.
Direction advice (navigation)
CHECK (vehicle autotest).
Trip computer information
displays.
Warning and status displays.
12. Instrument panel lighting rheostat.
6. Warning lights:
h a n d b r a k e a p p l i e d o r b r a k e fl u i d
level or electronic brake force
distribution fault.
right direction indicator.
7. Speedometer dial.
8. Warning lights:
emission control system.
anti-lock braking system (ABS).
passenger air bag disarmed.
pre-heat (diesel engine starting).
9. Engine oil temperature indicator
dial.
Page 21 of 250
1INSTRUMENTS and CONTROLS
22
Battery charge warning
light
When the engine is running, this in-
dicates a charging circuit malfunction
(battery terminals, alternator belt).
Consult a PEUGEOT dealer. T y r e u n d e r - i n fl a t i o n w a r n i n g
light
This indicates that the tyre pressure is
too low.
A message on the multifunction display
indicates the wheel(s) concerned.
R e f e r t o t h e i n f o r m a t i o n l a b e l a f fi x e d
to the central pillar of the driver's door.
For your safety, check the tyre pres-
sures as soon as possible.
Electronic stability control system
(ESP) warning lights Activation warning light
Operation warning light
Deactivation warning light
Malfunction warning light
Power steering warning
light
This indicates a power steering fault.
It is linked with the STOP warning
light.
Consult a PEUGEOT dealer. Handbrake warning light
This indicates that the handbrake is
still applied or has not been released
correctly.
It is linked with the braking system
warning light. Low wash-wipe and
h e a d l a m p w a s h fl u i d l e v e l
warning light
When the wipers are switched on, this
i n d i c a t e s t h a t t h e fl u i d l e v e l i s t o o l o w .
Fill the wash-wipe and headlamp wash
fl u i d r e s e r v o i r .
Engine oil level warning
light
This indicates a critical engine oil level
(too low).
WARNING LIGHTS ON THE INSTRUMENT PANEL DISPLAY
These warning lights are displayed on
the instrument panel display.
STOP warning light
When this is displayed alone, it indi-
cates a power steering fault.
It comes on linked with the engine oil
pressure, coolant temperature, brak-
ing system or punctured tyre warning
lights.
Stop immediately.
Consult a PEUGEOT dealer.
Punctured tyre warning light
This indicates that one or more punc-
tured tyres have been detected.
A message on the multifunction display
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
light.
Stop immediately.
Consult a PEUGEOT dealer.
Stop immediately.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Page 22 of 250
1INSTRUMENTS and CONTROLS
23
T y r e u n d e r - i n fl a t i o n d e t e c t i o n
system warning light
This indicates the absence or mal-
function of one or more tyre pressure
sensors or a system fault.
Consult a PEUGEOT dealer.
Electronic engine
immobiliser warning light
This indicates an electronic engine im-
mobiliser system malfunction.
Consult a PEUGEOT dealer. Front brake pads wear
warning light
This indicates that the brake pads are
worn.
For your safety, have them replaced
by a PEUGEOT dealer.
Fuel tank cap warning light
(according to version)
With the engine running, this indicates
that the fuel tank cap is incorrectly se-
cured or absent.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above
6 mph (10 km/h).
W a t e r i n d i e s e l fi l t e r
warning light
This indicates the presence of water
i n t h e d i e s e l fi l t e r . T h e r e i s a r i s k o f
damage to the injection system.
Contact a PEUGEOT dealer as soon
as possible. Door/boot open warning
light
With the engine running, this indicates
that an access has not been closed
correctly.
An illustration on the multifunction
d i s p l a y i d e n t i fi e s t h e a c c e s s ( e s ) c o n -
cerned.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above
6 mph (10 km/h). Air bags warning light
This indicates an air bag fault.
Consult a PEUGEOT dealer.
Automatic headlamp beam
adjustment system warning
light
This indicates that the automatic
headlamp height adjuster is faulty.
Consult a PEUGEOT dealer.
Engine oil pressure warning
light
This indicates that the engine oil
pressure is too low.
It is linked with the STOP warning
light.
Stop immediately if it comes on while
the engine is running.
If there is a lack of oil in the lubrication
circuit, top up the level and contact a
PEUGEOT dealer as soon as possible.
Page 24 of 250
1INSTRUMENTS and CONTROLS
25
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever
position indicator lights
This indicates an automatic
gearbox malfunction.
4 or 6 speed automatic gearbox
"Park" indicator
lights
"Reverse" indicator
lights
"Neutral" indicator
lights
"Drive" indicator
lights
The letter S or the symbol associat-
ed with the gate lever position indicator
lights, corresponds to the Sport or Snow
programme selected intentionally. These correspond to the manual con-
trol of the gearbox, four or six speed.
When the engine speed is too low or
too high in relation to the gear engaged,
t h e g e a r s e l e c t e d fl a s h e s f o r a f e w s e c -
onds, then the actual gear is displayed,
the auto-adaptive programme having
taken control temporarily.
Engine oil temperature
indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone
C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. "Manual" indicator lights
Page 25 of 250
1INSTRUMENTS and CONTROLS
26
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule. Service indicator zero reset
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the reset procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
reset button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears .
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time the
ignition is switched on and for 5 seconds,
t h e d i s t a n c e a n d t h e s p a n n e r fl a s h .
Example
: when the ignition is switched
on and for 5 seconds, the display
indicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal
operation and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be weighted
by the time factor, depending on the
user’s driving habits.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising the service operations is
lit. The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
before the next service.
Example
: when switching on the
ignition and for 5 seconds, the dis-
play shows that 900 miles/km remain
before the next service is due.
After this operation, if you
wish to disconnect the battery,
lock the vehicle and wait for at
l e a s t fi v e m i n u t e s , o t h e r w i s e
the zero reset will not be
registered.
Page 26 of 250
1INSTRUMENTS and CONTROLS
27
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 5 seconds, after the
service information. Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.
A = max.
B = min. Trip recorder zero reset
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y
checking using the dipstick, it is impe-
rative that the level is topped up. Oil level gauge fault
( fl a s h i n g s e g m e n t s )
Check the oil level using the dipstick.
I f t h e l e v e l i s c o r r e c t , t h e fl a s h i n g
indicates an engine oil level gauge
malfunction.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes. The total distance is displayed in
zone A of the display and the trip
distance in zone B .
Distance recorder
With the trip distance displayed, press
the button for a few seconds.
Page 127 of 250
9CHECKS
110
CHECKING THE LEVELS
These are normal maintenance opera-
tions which keep your vehicle in good
working order. Consult the instructions
in the PEUGEOT Network or in the
servicing booklet enclosed with this
handbook.
Dipstick There are two marks on
the dipstick:
A = m a x i m u m
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
To maintain the reliability
of engines and emission
control systems, the use
of additives in engine oil is
prohibited.
Oil level
Check the level regularly and top
up between changes.
Check the level with the vehicle level,
the engine having been off for more
than 15 minutes, using the dipstick. Oil change
It is imperative that this is carried out at
t h e i n t e r v a l s s p e c i fi e d a n d t h e v i s c o s i t y
of the oil chosen must meet the require-
ments laid down in the manufacturer’s
servicing schedule. Consult the instruc-
tions in the PEUGEOT Network.
Note: avoid used oil coming into pro-
longed contact with the skin. Empty the
used oil into the containers provided for
this purpose in the PEUGEOT Network. system is pressurised, wait for at least
one hour after the engine has stopped
before carrying out any work.
Oil filter
Replace the cartridge regularly in
accordance with the recommendations
of the servicing schedule.
Brake fluid change
U s e t h e fl u i d r e c o m m e n d e d b y t h e
m a n u f a c t u r e r , w h i c h f u l fi l s D O T 4
Standards.
I t i s i m p e r a t i v e t h a t t h e b r a k e fl u i d i s
c h a n g e d a t t h e i n t e r v a l s s p e c i fi e d i n
accordance with the manufacturer’s
servicing schedule.
Note: avoid all contact with the skin,
t h e b r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
very corrosive. Used oil
Power steering reservoir
U s e t h e fl u i d r e c o m m e n d e d b y t h e
manufacturer.
Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
Cooling system Windscreen and headlamp
wash level
To guarantee optimum cleaning and
a v o i d f r e e z i n g , t h i s fl u i d s h o u l d n o t b e
topped up or replaced with water. Slacken the cap by two turns
to release the pressure to pre-
vent any risk of scalding. When
the pressure has dropped,
remove the cap and top up the
level.
Note: the coolant does not need to be
changed.
U s e t h e fl u i d r e c o m m e n d e d
by the manufacturer.
When the engine is warm, the
temperature of the coolant is
controlled by the engine fan. As this
fan can operate with the ignition key
removed and because the cooling Do not dispose of used oil,
b r a k e fl u i d o r c o o l a n t i n t o
drains or onto the ground.
Important: if you have to
r e m o v e / r e fi t t h e e n g i n e s t y l e
cover, handle it with care to
a v o i d d a m a g i n g t h e fi x i n g c l i p s .
Page 142 of 250
1010PRACTICAL INFORMATION
Engine compartment fuses
To access the fuses located in the
engine compartment (next to the bat-
tery), remove the battery cover and
unclip the fuse box cover.
Close the fuse box cover carefully and
r e fi t t h e b a t t e r y c o v e r w h e n y o u h a v e
fi n i s h e d .
Fuse N°
Rating
A
Functions
1 20 Engine management control unit.
2 15 Horn.
3 10 Front and rear wash-wipe.
4 20 Headlamp wash.
5 15 Engine management actuators (fuel pump,
purge canister solenoid valves, ...).
6 10 Automatic gearbox control unit.
7 10 Switching and protection unit, intake air
fl o w s e n s o r , c l u t c h s w i t c h , s i x - s p e e d
automatic gearbox switch, STOP switches,
electrochromatic mirror, panoramic roof
c o n c e a l i n g fl a p c o n t r o l s ( 4 0 7 S W ) .
8 20 Starter coil.
9 10 Xenon bulb electronic supply, STOP switch,
power steering electropump assembly,
four-speed automatic gearbox control unit,
automatic gearbox locking relay.
10 30 Engine management actuators (ignition coil,
solenoid valves, oxygen sensors).
11 40 Air conditioning blower or not used.
12 30 Windscreen wipers.
13 40 Built-in systems interface supply
(ignition positive).
14 30 Air pump.
Page 147 of 250
1010PRACTICAL INFORMATION
125
Without lifting
(4 wheels on the ground)
You must always use a towbar.
The removable towing eye is inside
the spare wheel.
At the front and at the rear:
Unclip the cover,
Screw in the towing eye as far as it
will go. Special features of the
automatic gearbox
When towing with the engine switched
off, there is no braking or steering
assistance.
Failure to observe this special require-
ment may lead to the destruction of
certain braking units and the absence
of braking assistance when the engine
is re-started.
TOWING YOUR VEHICLE
Lifting
(2 wheels only on the ground)
It is preferable to raise the vehicle with
a professional lifting device.
Place the gear lever in neutral
(position N in the case of the
automatic gearbox).
Towing a vehicle with an auto-
matic gearbox in reverse gear
is prohibited (absence of lubri-
cation). When towing with four wheels on the
ground, the following rules must be
obeyed:
- lever in position
N ,
- tow the vehicle at less than 30 mph (50 km/h) over a maximum dis-
tance of 30 miles (50 km).
- do not add oil to the gearbox.