key Peugeot 407 2010 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 407, Model: Peugeot 407 2010Pages: 249, PDF Size: 14.69 MB
Page 68 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to re-
trieve the key code and the transponder
code required to order a replacement key.
Page 69 of 249
4ACCESS
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REINITIALISATION
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking but-
ton immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator lamp
It is accompanied by a message on
the multi-function screen.
Your vehicle will not start.
Consult a PEUGEOT dealer.
This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the ig-
nition is switched on, the code must be
recognised for starting to be possible.
If the system does not function correct-
ly, the following indicator lamp comes on:
Remote control
The high frequency remote control is
a sensitive system; do not operate it
while it is in your pocket as there is a
possibility that it may unlock the vehi-
cle, without you being aware of it.
Do not repeatedly press the buttons of
your remote control out of range and
out of sight of your vehicle. You run the
risk of stopping it from working and the
remote control would have to be reini-
tialised.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off, ex-
cept for reinitialisation.
Locking the vehicle
Driving with the doors locked may
make access to the passenger com-
partment by the emergency services
m o r e d i f fi c u l t i n a n e m e r g e n c y .
As a safety precaution (with children
on board), remove the key from the
ignition when you leave the vehicle,
even for a short time. Lost keys
Visit a PEUGEOT dealer with
the vehicle's V5 registration
d o c u m e n t a n d y o u r p e r s o n a l i d e n t i fi -
cation documents.
The PEUGEOT dealer will be able to re-
trieve the key code and the transponder
code required to order a replacement key.
Page 70 of 249
4ACCESS
64
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a -
tions to the electronic engine
immobiliser system; this could
cause malfunctions. CHILD LOCK
This prevents opening of both of the
rear doors from the inside.
With the ignition on, press the button.
A message appears on the multi-func-
tion display.
This system is independent and does
not, in any circumstances, take the
place of the central locking control.
Electric mode
When purchasing a second-
hand vehicle
Have the key codes memorised by a
PEUGEOT dealer, to ensure that the
keys in your possession are the only
ones which can start the vehicle. Do not throw the remote con-
trol batteries away, they contain
metals which are harmful to the
environment.
Take them to an approved col-
lection point.
Always remove the ignition
key when leaving the vehicle,
even for a short time.
It is advisable to check that
the child lock is active each time the
ignition is switched on.
In the event of a serious impact, the
electric child lock is deactivated auto-
matically to permit the exit of the rear
passengers.
Page 71 of 249
4ACCESS
64
Anti-theft protection
D o n o t m a k e a n y m o d i fi c a -
tions to the electronic engine
immobiliser system; this could
cause malfunctions. CHILD LOCK
This prevents opening of both of the
rear doors from the inside.
With the ignition on, press the button.
A message appears on the multi-func-
tion display.
This system is independent and does
not, in any circumstances, take the
place of the central locking control.
Electric mode
When purchasing a second-
hand vehicle
Have the key codes memorised by a
PEUGEOT dealer, to ensure that the
keys in your possession are the only
ones which can start the vehicle. Do not throw the remote con-
trol batteries away, they contain
metals which are harmful to the
environment.
Take them to an approved col-
lection point.
Always remove the ignition
key when leaving the vehicle,
even for a short time.
It is advisable to check that
the child lock is active each time the
ignition is switched on.
In the event of a serious impact, the
electric child lock is deactivated auto-
matically to permit the exit of the rear
passengers.
Page 73 of 249
4ACCESS
66
Reactivation of the interior
volumetric monitoring
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp on the button again
fl a s h e s o n c e p e r s e c o n d . Triggering of the alarm
This is indicated by sounding of the
s i r e n a n d fl a s h i n g o f t h e d i r e c t i o n i n d i -
cators for thirty seconds.
The monitoring functions remain ac-
tive until the alarm has been triggered
eleven times in succession.
When the vehicle is unlocked using
t h e r e m o t e c o n t r o l , r a p i d fl a s h i n g o f
the indicator lamp on the button in-
forms you that the alarm was triggered
during your absence. When the igni-
t i o n i s s w i t c h e d o n , t h i s fl a s h i n g s t o p s
immediately.
Failure of the remote control
To deactivate the monitoring functions:
Unlock the vehicle using the key in
the driver's door lock.
Open the door; the alarm is trig-
gered.
Switch on the ignition; the alarm
stops. The indicator lamp on the
button switches off. Locking the vehicle without
activating the alarm
Lock or deadlock the vehicle using
the key in the driver's door lock.
Malfunction
W h e n t h e i g n i t i o n i s s w i t c h e d o n , fi x e d
lighting of the indicator lamp on the
button indicates a malfunction of the
system.
Have it checked by a PEUGEOT dealer.
* According to country.
Automatic activation *
2 minutes after the last door or the
boot is closed, the system is activated
automatically.
To avoid triggering the alarm on
e n t e r i n g t h e v e h i c l e , fi r s t p r e s s t h e
unlocking button on the remote
control.
Page 74 of 249
4ACCESS
67
ELECTRIC WINDOWS
Automatic operation:
To open or close the window, press or
pull switch fully: the window opens or
closes completely when the switch is
released. Pressing the switch again
stops the movement of the window.
The electric window switches remain
operational for approximately one min-
ute after the key has been removed
from the ignition.
Once this time has elapsed, the electric
windows will not operate. To reactivate
them, switch the ignition on again.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the windows, you must re-
verse the movement of the window. To
do this, press the switch concerned.
When the driver operates the passen-
ger electric window switches, he must
ensure that no one is preventing cor-
rect closing of the windows.
The driver must ensure that the pas-
sengers use the electric windows cor-
rectly.
Be aware of children when operating
the windows. REINITIALISATION OFTHE ELECTRIC WINDOWS
Following reconnection of the battery,
the safety anti-pinch function must be re-
initialised: the safety anti-pinch function
is not active during these operations.
- lower the window completely, then raise it, it will rise in steps of a few
centimetres each time the switch is
pressed. Repeat the operation un-
til the window closes completely,
- continue to press the switch for at least one second after reaching
this position, window closed.
Safety anti-pinch
When the window rises and meets an
obstacle, it stops and immediately par-
tially lowers again.
In the event of unwanted opening
of the window on closing, press the
switch until the window opens com-
pletely, then pull the switch immediate-
ly until the window closes. Continue to
hold the switch for approximately one
second after the window has closed.
The safety anti-pinch function is not
active during this operation.
Deactivating the rear window
controls
For the safety of your children, press
switch 5 to prevent operation of the rear
windows irrespective of their position.
When the button is pressed down, the
switches are deactivated. When the but-
ton is raised, the switches are active.
Manual operation:
To open or close the window, press
or pull the switch gently. The win-
dow stops as soon as the switch is
released.
1. Driver's electric window switch.
2. Passenger's electric window
switch.
3. Rear right electric window
switch.
4. Rear left electric window
switch.
5. Deactivating the rear electric
window switches (child safety).
Page 78 of 249
4ACCESS
70
Notes:
After reconnecting the battery, you
must reinitialise the safety anti-pinch:
- place the control in the maximum partial opening position (3rd notch
to the right),
- wait until the roof is in the maxi- mum partially open position,
- press the control for at least one second.
In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), and immediately af-
ter the roof stops:
- move the control to the "O" position and press the control immediately,
- continue to press the control until the roof is fully closed. SUNROOF (SALOON) Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
In the event of contact during
operation of the roof, you must reverse
the movement of the roof. To do this,
press the switch concerned.
When the driver operates the roof
switch, they must ensure that no one
is preventing correct closing of the
roof.
The driver must ensure that passen-
gers use the sunroof correctly.
Be aware of children when operating
the roof.
- To partially open the roof: Turn the switch to the right (three possible
settings).
- To open the roof completely: Turn the switch to the left (six possible
settings).
- To close it completely: Turn the switch back to position "O".
- Safety anti-pinch: When the sun- roof is closing and meets an ob-
stacle, it stops then partially opens
again.
The sunroof blind is manual.
Page 90 of 249
5
79
Windscreen and headlamp wash
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
w i n d s c r e e n w i p e r s o p e r a t e f o r a fi x e d
period.
T h e h e a d l a m p w a s h i s a l s o a c t i v a t e d ,
if the headlamps are on .
W h e n t h e m i n i m u m l e v e l o f
the reservoir is reached, this
w a r n i n g l i g h t c o m e s o n , a c -
c o m p a n i e d b y a n a u d i b l e
s i g n a l a n d a m e s s a g e o n t h e
m u l t i - f u n c t i o n d i s p l a y .
N e x t t i m e y o u s t o p , fi l l t h e s c r e e n w a s h /
h e a d l a m p w a s h r e s e r v o i r .
T h e w a r n i n g l i g h t c o m e s o n e a c h t i m e
the stalk is operated, until the reservoir
i s fi l l e d . FRONT COURTESY LAMP
T h e c o u r t e s y l a m p c a n b e d e a c t i v a t e d
by pressing switch 1 with the door open.
T h e m a p r e a d i n g l a m p s a r e n o t a f f e c t e d
b y t h i s a n d m a y b e s w i t c h e d o n .
T o r e - a c t i v a t e t h e l a m p s , p r e s s t h e
switch, with the door open.
Screenwash/headlamp wash low
1. Courtesy lamp
2. Map reading lamps
With the key in the ignition on or starting
position, operate the relevant switch.
T h e f r o n t c o u r t e s y l a m p c o m e s o n
w h e n t h e i g n i t i o n k e y i s r e m o v e d , o n
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or when the ve-
hicle is locked.
Pressing switch 1 turns on the front
c o u r t e s y l a m p .
Rear wash-wipe
Note: the rear wiper and rear
wash-wipe functions are de-
a c t i v a t e d a u t o m a t i c a l l y w h e n
the rear screen is opened.
T u r n t h e r i n g b e y o n d t h e fi r s t n o t c h ,
the wash-wipe then the wiper operate
f o r a s e t p e r i o d o f t i m e .
Page 91 of 249
5
79
Windscreen and headlamp wash
Pull the windscreen wiper stalk towards
you. The windscreen wash then the
w i n d s c r e e n w i p e r s o p e r a t e f o r a fi x e d
period.
T h e h e a d l a m p w a s h i s a l s o a c t i v a t e d ,
if the headlamps are on .
W h e n t h e m i n i m u m l e v e l o f
the reservoir is reached, this
w a r n i n g l i g h t c o m e s o n , a c -
c o m p a n i e d b y a n a u d i b l e
s i g n a l a n d a m e s s a g e o n t h e
m u l t i - f u n c t i o n d i s p l a y .
N e x t t i m e y o u s t o p , fi l l t h e s c r e e n w a s h /
h e a d l a m p w a s h r e s e r v o i r .
T h e w a r n i n g l i g h t c o m e s o n e a c h t i m e
the stalk is operated, until the reservoir
i s fi l l e d . FRONT COURTESY LAMP
T h e c o u r t e s y l a m p c a n b e d e a c t i v a t e d
by pressing switch 1 with the door open.
T h e m a p r e a d i n g l a m p s a r e n o t a f f e c t e d
b y t h i s a n d m a y b e s w i t c h e d o n .
T o r e - a c t i v a t e t h e l a m p s , p r e s s t h e
switch, with the door open.
Screenwash/headlamp wash low
1. Courtesy lamp
2. Map reading lamps
With the key in the ignition on or starting
position, operate the relevant switch.
T h e f r o n t c o u r t e s y l a m p c o m e s o n
w h e n t h e i g n i t i o n k e y i s r e m o v e d , o n
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or when the ve-
hicle is locked.
Pressing switch 1 turns on the front
c o u r t e s y l a m p .
Rear wash-wipe
Note: the rear wiper and rear
wash-wipe functions are de-
a c t i v a t e d a u t o m a t i c a l l y w h e n
the rear screen is opened.
T u r n t h e r i n g b e y o n d t h e fi r s t n o t c h ,
the wash-wipe then the wiper operate
f o r a s e t p e r i o d o f t i m e .
Page 92 of 249
5
80
REAR COURTESY LAMP (SALOON) REAR READING LAMPS (407 SW) Sill illumination
T h e s i l l l i g h t i n g i s a t t h e b o t t o m o f e a c h
door panel.
T h e l a m p s c o m e o n a u t o m a t i c a l l y
when a door is opened and switch off
a u t o m a t i c a l l y w h e n a l l o f t h e d o o r s a r e
closed.
Boot light
The boot light is located in the right-
h a n d b o o t t r i m .
I t c o m e s o n a u t o m a t i c a l l y w h e n t h e
boot is opened and switches off auto-
m a t i c a l l y w h e n t h e b o o t i s c l o s e d .
1. Courtesy lamp
2. Map reading lamps
With the key in the ignition on or start-
ing position, operate the relevant
switch.
T h e r e a r c o u r t e s y l a m p c o m e s o n
w h e n t h e i g n i t i o n k e y i s r e m o v e d , o n
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or the vehicle
is locked.
Pressing switch 1 turns on the rear
c o u r t e s y l a m p .
T h e c o u r t e s y l a m p c a n b e d e a c t i v a t e d
by pressing switch 1 with the door open.
T h e m a p r e a d i n g l a m p s a r e n o t a f f e c t e d
b y t h i s a n d m a y b e s w i t c h e d o n .
T o r e - a c t i v a t e t h e l a m p s , p r e s s t h e
switch, with the door open. With the key in the ignition on or start-
ing position, press the corresponding
switch.
T h e r e a r r e a d i n g l a m p s c o m e o n w h e n
t h e k e y i s r e m o v e d f r o m t h e i g n i t i o n
and when the vehicle is unlocked.
They switch off gradually when the ig-
nition is switched on or when the ve-
hicle is locked.
Pressing switch 1 switches on the
r e a r r e a d i n g l a m p c o n c e r n e d f o r
t e n m i n u t e s .