bonnet Peugeot 407 2010 Owner's Manual

FAMILIARISATION
Remote control key

A. Unfolding/folding the key.

B. Unlocking the vehicle
(brief press).

C.
Unlocking and partial opening of the
boot (saloon) or of the rear screen (SW)
(long press).

Also...

D. Normal locking
(a single press)
or
deadlocking of the vehicle
(two presses in succession). Fuel tank

1. Opening of the fuel fi ller fl ap.

2. Opening and hooking of the fuel
tank cap.
Tank capacity: approximately 67 litres.

A. Interior control.

B. Exterior control.

 61

 72  106
Bonnet

FAMILIARISATION INSTRUMENTS AND CONTROLS
1. Audio equipment steering wheel
stalk.

2. Steering lock and ignition.

3. Steering wheel height and depth
adjustment.

4. Cruise control/speed limiter stalk.

5. Lights/Direction indicator stalk.

6. Air conditioned glove box.
Fuse box.

7. Bonnet release.

8. Passenger-operated electric
window control.

9. Speakers (tweeters).

10. Air diffuser vent grille.

11. Instrument panel.

12. Wiper/Wash-wipe/Trip computer
stalk.

13. Headlamp height adjustment.

14. Storage compartment (driver’s side).

4ACCESS
65
ALARM
For all work on the alarm system, contact
a PEUGEOT dealer.
- Exterior perimeter
The system checks for opening of the
vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- Interior volumetric
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks
a window, enters the passenger com-
partment or moves inside the vehicle.
Self-protection function
The system checks for the
putting out of service of its
components.
The alarm is triggered if the battery, the
central control or the wires of the siren
are put out of service or damaged. Locking the vehicle with full
alarm system
Activation

 Switch off the ignition and get out
of the vehicle.

 Press the locking button on the re-
mote control.
The monitoring system is active: the
indicator lamp on the button fl ashes
once per second.
After the locking button on the remote
control is pressed, the exterior perime-
ter monitoring is activated after a delay
of 5 seconds and the interior volumetric
after a delay of 45 seconds.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric monitoring.
System which protects and provides a
deterrent against theft and break-ins.
It provides the following types of moni-
toring.
Deactivation

 Press the unlocking button on the
remote control.
The alarm system is deactivated: the in-
dicator lamp on the button switches off.
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric pro-
tection to avoid unwanted triggering of
the alarm in certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea.
Deactivation of the interior
volumetric monitoring

 Switch off the ignition.

 Within ten seconds, press the but-
ton until the indicator lamp is lit
continuously.

 Get out of the vehicle.

 Press the locking button on the re-
mote control immediately.

The exterior perimeter monitoring alone
is activated: the indicator lamp on the
button fl ashes once per second.
To be effective, this deactivation must
be carried out each time the ignition is
switched off.

9CHECKS
106
Bonnet stay BONNET
Handle the exterior safety catch and
the bonnet stay with care when the en-
gine is hot (risk of burns).
Opening

From inside: pull the release lever on
the left-hand side under the dashboard
towards you.

From outside: move the safety catch to
the left and up then raise the bonnet. Secure the stay in its housing to hold
the bonnet open.
Before closing the bonnet, replace the
stay in its clip. Closing
Lower the bonnet and release it at the
end of its travel. Check that the bonnet
is fully closed.

9CHECKS
111
CHECKING THE LEVELS
These are normal maintenance opera-
tions which keep your vehicle in good
working order. Obtan advice from the
PEUGEOT dealer network or from the
Warranty and Maintenance Record
provided with the vehicle.
If you have to remove/refi t the engine
style cover, handle it with care to avoid
damaging the fi xing clips.
Dipstick There are two marks on
the dipstick:

A = maximum
Never fi ll past this mark.

B = minimum
To maintain the reliability
of engines and emission
control systems, the use
of additives in engine oil is
prohibited.
Oil level

 Check the level regularly and top
up between changes.
Check the level with the vehicle level,
the engine having been off for more
than 15 minutes, using the dipstick. Oil change
It is essential that this is carried out at
the intervals specifi ed and the viscosity
of the oil chosen must meet the require-
ments laid down in the manufacturer's
servicing schedule. Ask for advice from
the PEUGEOT dealer network.

Note : avoid used oil coming into pro-
longed contact with the skin. Empty
the used oil into the containers provid-
ed for this purpose in the PEUGEOT
dealer network (France) or take it to
an approved recycling centre. system is pressurised, wait for at least
one hour after the engine has stopped
before carrying out any work.
Oil filter
Replace the fi lter regularly in accor-
dance with the recommendations of
the servicing schedule.
Brake fluid change
Use the fl uid recommended by the
manufacturer, which fulfi ls the DOT4
standard.
It is essential that the brake fl uid is
changed at the intervals specifi ed in
the manufacturer's servicing schedule.

Note : avoid all contact with the skin;
the brake fl uid is harmful to health and
is very corrosive. Used oil
Power steering reservoir
Use the fl uid recommended by the
manufacturer.

 Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
Cooling system Screenwash and headlamp
wash level
To ensure optimum cleaning and avoid
freezing, this fl uid should not be topped
up or replaced with plain water. Slacken the cap by two turns
to release the pressure to pre-
vent any risk of scalding. When
the pressure has dropped, re-
move the cap and top up the level.

Note : the coolant does not need to be
changed.
Use the fl uid recommended
by the manufacturer.
When the engine is warm, the
temperature of the coolant is
controlled by the engine fan. As this
fan can operate with the ignition key
removed and because the cooling Do not dispose of used oil,
brake fl uid or coolant into
drains or onto the ground.
Take care when working un-
der the bonnet, as some parts
of the engine can be very hot
(risk of burns).

9CHECKS
112
CHECKS
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Have the fi lter elements
replaced regularly. If you
drive in dusty conditions,
change them twice as often.
Air filter and passenger compartment filter
Particle emission filter (Diesel)
It is essential that the particle emission
fi lter is maintained in accordance with
the manufacturer's servicing schedule,
by a PEUGEOT dealer.

Note : following prolonged operation
of the vehicle at very low speed or at
idle, you may, in exceptional circum-
stances, notice emissions of water va-
pour at the exhaust on acceleration.
This does not have any effect on the
performance of the vehicle or the en-
vironment.
On vehicles which are fi tted with a par-
ticle emission fi lter, the cooling fan may
operate after the vehicle has stopped,
even when the engine is cold. Where the parking brake trav-
el is too great or there is a re-
duction in the performance of
the system, the parking brake
should be adjusted.
Have the system checked by a PEUGEOT
dealer.
Parking brake
Disc wear status
For any information relating to check-
ing disc wear, contact a PEUGEOT
dealer.
FUEL SUPPLY CUT-OFF (PETROL) *
As a safety precaution, in certain cir-
cumstances the fuel supply to the en-
gine is cut off.
To re-establish the fuel supply:
RUNNING OUT OF FUEL (DIESEL)
If you should run out of fuel, it is ne-
cessary to prime the fuel system.
The priming pump and the bleed screw
are located under the bonnet (see cor-
responding illustration in the technical
information section):
1.6 litre 16V HDI engine
- fi ll the fuel tank with at least fi ve li-
tres of diesel,
- squeeze and release the manual priming pump until fuel appears in
the transparent pipe,
- operate the starter until the engine starts.
2 litre 16V HDI engine
- fi ll the fuel tank with at least fi ve li- tres of diesel,
- unscrew the bleed screw,
- squeeze and release the manual priming pump until diesel is seen
escaping via the bleed screw,
- retighten the bleed screw,
- operate the starter until the engine starts.
Brake pad wear depends on
the style of driving, in particu-
lar for vehicles which are used
in town, over short distances.
Brake pads It may be necessary to check
the brake pads for wear, even
between services.
* According to version.
To ensure the best perfor-
mance from components as
important as the power steer-
ing and the braking system,
the manufacturer selects and offers
specifi c products, only use products
recommended by PEUGEOT.
Battery
To prevent damage to the electrical
units, high pressure washing of the en-
gine compartment is strictly prohibited .
 press the red button on the angle
of the front right-hand suspension
housing, under the bonnet.