coolant level Peugeot 407 2010 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 407, Model: Peugeot 407 2010Pages: 249, PDF Size: 14.69 MB
Page 16 of 249
1
19
1. Coolant temperature gauge.
2. Lighting on indicators:
dipped beam headlamps.
main beam headlamps.
front foglamps.
rear foglamps.
3. Rev counter dial.
4. Warning lamps:
seat belts not fastened in the front.
fuel level.
left direction indicator.
5. Fuel level gauge.
PETROL-DIESEL MANUAL AND AUTOMATICGEARBOX INSTRUMENT PANELS
10. CHECK and trip recorder zero
reset and service display button.
11. Instrument panel screen:
Total distance recorder.
Trip recorder.
Automatic gearbox lever position indicator.
Cruise control/speed limiter reference value.
Service indicator.
Navigation instructions
CHECK (vehicle autotest).
Trip computer information displays.
Warning and status displays.
12. Instrument panel lighting rheostat.
6. Warning lamps:
parking brake applied or brake fl u i d l e v e l o r e l e c t r o n i c b r a k e f o r c e
distribution fault.
right direction indicator.
7. Speedometer.
8. Warning lamps:
emission control system.
anti-lock braking system (ABS).
passenger's airbag deactivated.
pre-heat (Diesel engine starting).
9. Engine oil temperature gauge.
Page 19 of 249
1
21
Fuel warning lamp
In certain driving conditions and de-
pending on the engine, the distance
which you will be able to travel with
the remaining fuel may be less than
30 miles (50 kilometres) (the capacity
of the tank is approximately 67 litres).
Emission control system
warning lamp
This should switch off a few seconds
after the engine is switched on.
When the engine is running, if the
w a r n i n g l a m p fl a s h e s o r c o m e s o n
continuously, this indicates an emis-
sion control system malfunction.
Contact a PEUGEOT dealer as soon
as possible. Diesel engine pre-heat
warning lamp
Wait for the warning lamp to switch off
before starting. The illumination period
is determined by the ambient conditions.
Passenger's airbag
deactivated warning lamp *
If the warning lamp remains on, this
indicates that the passenger's airbag
has been deactivated intentionally.
If it comes on continuously above 6 mph
(10 km/h), it indicates an ABS fault.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
Anti-lock braking system
(ABS) warning lamp
* According to country.
The warning lamp is repea-
ted on the instrument panel
screen.
When the needle is in zone
A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature warning
lamp comes on (linked with the STOP
warning lamp), stop as soon as it is
safe to do so.
Wait for the engine to cool down be-
fore topping up the level, if necessary.
As the cooling circuit is pressurised, in
order to prevent any risk of scalding,
unscrew the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level, if
necessary.
Consult a PEUGEOT dealer.
Page 20 of 249
1
21
Fuel warning lamp
In certain driving conditions and de-
pending on the engine, the distance
which you will be able to travel with
the remaining fuel may be less than
30 miles (50 kilometres) (the capacity
of the tank is approximately 67 litres).
Emission control system
warning lamp
This should switch off a few seconds
after the engine is switched on.
When the engine is running, if the
w a r n i n g l a m p fl a s h e s o r c o m e s o n
continuously, this indicates an emis-
sion control system malfunction.
Contact a PEUGEOT dealer as soon
as possible. Diesel engine pre-heat
warning lamp
Wait for the warning lamp to switch off
before starting. The illumination period
is determined by the ambient conditions.
Passenger's airbag
deactivated warning lamp *
If the warning lamp remains on, this
indicates that the passenger's airbag
has been deactivated intentionally.
If it comes on continuously above 6 mph
(10 km/h), it indicates an ABS fault.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
Anti-lock braking system
(ABS) warning lamp
* According to country.
The warning lamp is repea-
ted on the instrument panel
screen.
When the needle is in zone
A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature warning
lamp comes on (linked with the STOP
warning lamp), stop as soon as it is
safe to do so.
Wait for the engine to cool down be-
fore topping up the level, if necessary.
As the cooling circuit is pressurised, in
order to prevent any risk of scalding,
unscrew the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level, if
necessary.
Consult a PEUGEOT dealer.
Page 21 of 249
1
22
Battery charge warning
lamp
When the engine is running, this in-
dicates a charging circuit malfunction
(battery terminals, alternator belt).
Consult a PEUGEOT dealer. T y r e u n d e r - i n fl a t i o n w a r n i n g
lamp
This indicates that the tyre pressure is
too low.
A message on the multifunction screen
indicates the wheel(s) concerned.
R e f e r t o t h e i n f o r m a t i o n l a b e l a f fi x e d
to the central pillar of the driver's door.
For your safety, check the tyre pres-
sures as soon as possible.
Electronic stability control system
(ESP) warning lamps Activation warning lamp
Operation warning lamp
Deactivation warning lamp
Malfunction warning lamp
Power steering warning
lamp
This indicates a power steering fault.
It is linked with the STOP warning
lamp.
Consult a PEUGEOT dealer. Parking brake warning lamp
This indicates that the parking brake is
still applied or has not been released
correctly.
It is linked with the braking system
warning lamp. Low screenwash and
h e a d l a m p w a s h fl u i d l e v e l
warning lamp
When the wipers are switched on, this
i n d i c a t e s t h a t t h e fl u i d l e v e l i s t o o l o w .
Fill the screenwash and headlamp
w a s h fl u i d r e s e r v o i r .
Engine oil level warning
lamp
This indicates that the engine oil level
is too low.
WARNING LAMPS IN THE INSTRUMENT PANEL SCREEN
These warning lamps are displayed
on the instrument panel screen.
STOP warning lamp
When this is displayed alone, it indi-
cates a power steering fault.
It comes on linked with the engine oil
pressure, coolant temperature, bra-
king system or punctured tyre warning
lamps.
Stop as soon as it is safe to do so.
Consult a PEUGEOT dealer.
Punctured tyre warning lamp
This indicates that one or more punc-
tured tyres have been detected.
A message on the multifunction screen
i d e n t i fi e s t h e w h e e l ( s ) c o n c e r n e d .
It is linked with the STOP warning
lamp.
Stop as soon as it is safe to do so.
Consult a PEUGEOT dealer.
Stop as soon as it is safe to do so.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Page 122 of 249
9CHECKS
107
1.8 LITRE 16V, 2 LITRE 16V, 2 LITRE 16V BIOFLEX PETROL ENGINES
* According to country.
Important: if you have to re-
m o v e o r r e fi t t h e e n g i n e s t y l e
cover, handle it with care to
a v o i d d a m a g i n g t h e fi x i n g c l i p s .
Check the levels!
1. Power steering reservoir.
2. Engine coolant reservoir
(header tank).
3. E n g i n e o i l fi l l e r c a p .
4. B r a k e fl u i d r e s e r v o i r .
5. A i r fi l t e r .
6. Engine oil dipstick.
7. Screenwash and headlamp * wash
r e s e r v o i r fi l l e r c a p .
Page 123 of 249
9CHECKS
108
2.2 LITRE 16V AND 3 LITRE V6 24V PETROL ENGINES
* According to country.
Important: if you have to re-
m o v e o r r e fi t t h e e n g i n e s t y l e
cover, handle it with care to
a v o i d d a m a g i n g t h e fi x i n g c l i p s .
Check the levels!
1. Power steering reservoir.
2. Engine coolant reservoir
(header tank).
3. E n g i n e o i l fi l l e r c a p .
4. B r a k e fl u i d r e s e r v o i r .
5. A i r fi l t e r .
6. Engine oil dipstick.
7. Screenwash and headlamp * wash
r e s e r v o i r fi l l e r c a p .
Page 124 of 249
9CHECKS
109
1.6 LITRE HDI 16V AND 2 LITRE HDI 16V DIESEL ENGINES
* According to country.
Important : if you have to re-
m o v e / r e fi t t h e e n g i n e s t y l e c o -
ver, handle it with care to avoid
d a m a g i n g t h e fi x i n g c l i p s .
Check the levels!
1. Power steering reservoir.
2. Engine coolant reservoir
(header tank).
3. E n g i n e o i l fi l l e r c a p .
4. B r a k e fl u i d r e s e r v o i r .
5. A i r fi l t e r .
6. Engine oil dipstick.
7. Screenwash and headlamp wash *
r e s e r v o i r fi l l e r c a p .
8. Priming pump.
9. Bleed screw.
Page 125 of 249
9CHECKS
110
2.2 LITRE HDI 16V DIESEL ENGINES
* According to country.
Important: if you have to re-
m o v e / r e fi t t h e e n g i n e s t y l e c o -
ver, handle it with care to avoid
d a m a g i n g t h e fi x i n g c l i p s .
Check the levels!
1. Power steering reservoir.
2. Engine coolant reservoir
(header tank).
3. E n g i n e o i l fi l l e r c a p .
4. B r a k e fl u i d r e s e r v o i r .
5. A i r fi l t e r .
6. Engine ol dipstick.
7. Screenwash and headlamp wash *
r e s e r v o i r fi l l e r c a p .
8. Priming pump.
9. Bleed screw.
Page 126 of 249
9CHECKS
111
CHECKING THE LEVELS
These are normal maintenance opera-
tions which keep your vehicle in good
working order. Obtan advice from the
PEUGEOT dealer network or from the
Warranty and Maintenance Record
provided with the vehicle.
I f y o u h a v e t o r e m o v e / r e fi t t h e e n g i n e
style cover, handle it with care to avoid
d a m a g i n g t h e fi x i n g c l i p s .
Dipstick There are two marks on
the dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
To maintain the reliability
of engines and emission
control systems, the use
of additives in engine oil is
prohibited.
Oil level
Check the level regularly and top
up between changes.
Check the level with the vehicle level,
the engine having been off for more
than 15 minutes, using the dipstick. Oil change
It is essential that this is carried out at
t h e i n t e r v a l s s p e c i fi e d a n d t h e v i s c o s i t y
of the oil chosen must meet the require-
ments laid down in the manufacturer's
servicing schedule. Ask for advice from
the PEUGEOT dealer network.
Note : avoid used oil coming into pro-
longed contact with the skin. Empty
the used oil into the containers provid-
ed for this purpose in the PEUGEOT
dealer network (France) or take it to
an approved recycling centre. system is pressurised, wait for at least
one hour after the engine has stopped
before carrying out any work.
Oil filter
R e p l a c e t h e fi l t e r r e g u l a r l y i n a c c o r -
dance with the recommendations of
the servicing schedule.
Brake fluid change
U s e t h e fl u i d r e c o m m e n d e d b y t h e
m a n u f a c t u r e r , w h i c h f u l fi l s t h e D O T 4
standard.
I t i s e s s e n t i a l t h a t t h e b r a k e fl u i d i s
c h a n g e d a t t h e i n t e r v a l s s p e c i fi e d i n
the manufacturer's servicing schedule.
Note : avoid all contact with the skin;
t h e b r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
is very corrosive. Used oil
Power steering reservoir
U s e t h e fl u i d r e c o m m e n d e d b y t h e
manufacturer.
Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
Cooling system Screenwash and headlamp
wash level
To ensure optimum cleaning and avoid
f r e e z i n g , t h i s fl u i d s h o u l d n o t b e t o p p e d
up or replaced with plain water. Slacken the cap by two turns
to release the pressure to pre-
vent any risk of scalding. When
the pressure has dropped, re-
move the cap and top up the level.
Note : the coolant does not need to be
changed.
U s e t h e fl u i d r e c o m m e n d e d
by the manufacturer.
When the engine is warm, the
temperature of the coolant is
controlled by the engine fan. As this
fan can operate with the ignition key
removed and because the cooling Do not dispose of used oil,
b r a k e fl u i d o r c o o l a n t i n t o
drains or onto the ground.
Take care when working un-
der the bonnet, as some parts
of the engine can be very hot
(risk of burns).