warning Peugeot 407 C Dag 2008 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 407 C Dag, Model: Peugeot 407 C Dag 2008Pages: 211, PDF Size: 11.75 MB
Page 24 of 211
1
27
Coolant temperature indicator
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature
warning light comes on (linked
with the STOP warning light),
stop immediately.
Wait for the engine to cool
down before topping up the level, if
necessary.
As the cooling circuit is pres-
surised, in order to prevent
any risk of scalding, unscrew
the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, remove
the cap and top up the level with coolant,
if necessary.
Consult a PEUGEOT dealer.
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever position indicator lights
Automatic gearbox fault
warning light
This indicates an automatic
gearbox fault.
The gearbox will operate in down-grade
mode, locked in 3rd gear.
Never force the selector lever.
Consult a PEUGEOT dealer.
6 speed automatic gearbox
"Park" indicator
lights
"Reverse" indicator
lights
"Neutral" indicator
lights
"Drive" indicator
lights
The letter S or the symbol
, associa-
ted with the gate lever position indicator
lights, corresponds to the Sport or Snow
programme selected intentionally. "Manual" indicator lights
These correspond to the manual control
of the gearbox.
When the engine speed is too low or too
high in relation to the gear engaged, the
g e a r s e l e c t e d fl a s h e s f o r a f e w s e c o n d s ,
then the actual gear is displayed, the
auto-adaptive programme having taken
control temporarily.
Page 31 of 211
1
32
Press the "MENU" button to gain access
to the general menu.
Select the "Trip computer" or "Vehicle
diagnostics" application using the navi-
g a t o r , t h e n c o n fi r m o r p r e s s t h e "MODE"
button until you reach the trip computer
s c r e e n , t h e n c o n fi r m u s i n g "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Warnings log,
- Status of the functions,
- Inputting of the distance to be trav- elled.
Warnings log
This summarises the active warning
messages, displaying them on the
multifunction display in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled value.
Display on the instrument panel screen
All of the various items of trip computer
information also appear on the instrument
panel screen at the same time.
Distance remaining to be travelled (km or miles)
Average speed (km/h or mph)
Average consumption (l/100 or km/l or mpg)
Distance travelled (km or miles)
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
This is the distance remaining to the
destination, either calculated at any
time by the navigation if guidance is
activated or entered by the user, minus
the distance covered since the distance
was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last set to
zero.
This indicates the distance travelled
since the computer was last set to
zero.
"TRIP" (Route) menu
Page 32 of 211
2
33
COLOUR SCREEN C
This displays the following information,
via the WIP Sound audio system control
pad:
- the time,
- the date,
- the exterior temperature (the value d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k
of ice),
- t h e a c c e s s e s c h e c k ,
- the warning messages,
- the audio functions,
- the trip computer information,
- t h e p e r s o n a l i s a t i o n a n d c o n fi g u r a t i o n displays,
- the air conditioning parameters,
- t h e f r o n t a n d r e a r p a r k i n g a s s i s t a n c e display,
- t h e h a n d s - f r e e k i t d i s p l a y s . Management of the displays
General menu
Press the
"MENU" button to gain access
to the general menu and select one of
the following functions:
- "Audio functions",
- "Trip computer",
- " P e r s o n a l i s a t i o n - C o n fi g u r a t i o n " ,
- "Air conditioning",
- " T e l e p h o n e " . " P e r s o n a l i s a t i o n - C o n fi g u r a t i o n "
menu
This provides access to successive
c o n fi r m a t i o n w i n d o w s .
D e fi n i n g t h e v e h i c l e p a r a m e t e r s
This enables you to activate or deactivate
certain driving and comfort elements:
- "Automatic switching on of the
lights",
- "Follow-me-home lighting" and "Duration",
- "Remote control action",
- " P e r m a n e n t l o c k i n g o f t h e b o o t " ,
- " D i r e c t i o n a l h e a d l a m p s " .
The
"AUDIO" , "TRIP" , "CLIM" and
"TEL" buttons on the RD4 audio equip-
ment control pad permit displaying in
t h e m a i n w i n d o w .
Example: "TRIP"
Example: "Audio functions"
Example: "Automatic switching on of
the lights"
Page 34 of 211
2
35
16/9 COLOUR SCREEN DT
This displays the following information,
via the WIP Com audio and telematics
system control panel:
- the time,
- the date,
- the outside temperature (the value d i s p l a y e d fl a s h e s i f t h e r e i s a r i s k
of ice),
- the status of the accesses,
- the warning messages or vehicle function status messages, displayed
temporarily,
- the audio functions,
- the telematic systems display ( t e l e p h o n e , s e r v i c e s , . . . ) ,
- the trip computer information,
- t h e p e r s o n a l i s a t i o n a n d c o n fi g u r a t i o n displays,
- the air conditioning parameters,
- t h e f r o n t a n d r e a r p a r k i n g a s s i s t a n c e display,
- the satellite navigation system i n f o r m a t i o n . General menu
Press the
"MENU" button to access
the general menu and select one of
the following functions:
- "Navigation - guidance",
- "Map",
- " T r a f fi c i n f o r m a t i o n " ,
- "Audio functions",
- "Telematics",
- " C o n fi g u r a t i o n " ,
- "Video",
- "Vehicle diagnostics",
- " A i r c o n d i t i o n i n g " . " C o n fi g u r a t i o n " m e n u
This provides access to the following
functions:
- " D i s p l a y c o n fi g u r a t i o n " ,
- "Sound",
- "Select language",
- " D e fi n e t h e v e h i c l e p a r a m e t e r s " .
Page 69 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the igni-
tion is switched on, the code is recognised
and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
I f t h e s y s t e m d o e s n o t f u n c -
tion correctly, the warning
light comes on on the instru-
ment panel display, accom-
panied by an audible signal
and a message on the multi-
function display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 72 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the igni-
tion is switched on, the code is recognised
and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
I f t h e s y s t e m d o e s n o t f u n c -
tion correctly, the warning
light comes on on the instru-
ment panel display, accom-
panied by an audible signal
and a message on the multi-
function display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 73 of 211
4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL
Switch off the ignition.
Switch the ignition on again.
Press the remote control locking
button immediately for a few seconds.
Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the igni-
tion is switched on, the code is recognised
and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
I f t h e s y s t e m d o e s n o t f u n c -
tion correctly, the warning
light comes on on the instru-
ment panel display, accom-
panied by an audible signal
and a message on the multi-
function display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
Page 75 of 211
4
68
THE ALARM
This provides two types of surveil-
lance:
- exterior protection: it sounds if
a door, the boot or the bonnet is
opened.
-
interior protection: it sounds if the
volume inside the passenger compart-
ment changes (breaking of a window
or a movement inside the vehicle).
When the alarm is triggered, the si-
ren sounds and the direction indica-
t o r l i g h t s fl a s h f o r a p p r o x i m a t e l y t h i r t y
seconds.
After triggering, the alarm remains set,
ten times in succession.
On the eleventh time it will become
inactive again, until the next cycle of
disarming then setting of the alarm.
Warning: if button A indicator light
fl a s h e s r a p i d l y , t h e a l a r m h a s b e e n
triggered while you were away from
your vehicle.
Incorrect operation
When the ignition is switched on, if
button A lights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have
the system checked.
R e m o t e c o n t r o l f a i l u r e , alarm set
Unlock the doors with the key and
open the door. The alarm is trig-
gered.
Switch on the ignition. The alarm is
disarmed.
* According to country.
Setting the alarm
Switch off the ignition and get out
of the vehicle.
Set the alarm, by locking or dead-
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once per second).
If you wish to lock or deadlock your
vehicle without setting the alarm, lock
it (one turn of the key) or deadlock it
( a s e c o n d t u r n w i t h i n fi v e s e c o n d s
maximum) using the lock.
The alarm is activated automatically
two minutes after the last closure of a
door or the boot.
In order to avoid accidental triggering
of the alarm when a door or the boot
is opened, it is essential to press the
unlocking button on the remote control
again.
Before setting the alarm, en-
sure that all of the accesses
(doors, bonnet, boot) are
closed correctly.
Disarming
Unlock the vehicle with the remote
control key.
The alarm is disarmed, indicator light A
goes out when the ignition is switched on.
T o s e t t h e a l a r m w i t h e x t e r i o r protection only
If, while you are away from the vehi-
cle, you wish to leave a window par-
tially open or a pet inside the vehicle,
you should choose exterior protection
only.
Switch off the ignition,
In the next ten seconds, press but-
ton A until the indicator light is on
continuously,
Get out of the vehicle,
Set the alarm by locking or dead-
locking using the remote control
(button A i n d i c a t o r l i g h t fl a s h e s
once a second).
Page 81 of 211
4
73
FILLING WITH FUEL
T h e f u e l fi l l e r fl a p i s e l e c t r i c , y o u c a n
only open it by pressing button A .
Button A is deactivated auto-
matically from 6 mph (10 km/h).
W h e n fi l l i n g w i t h f u e l , t h e
e n g i n e m u s t b e s w i t c h e d o f f
w i t h t h e i g n i t i o n o f f : O p e r a t i n g f a u l t
A fuel gauge fault is indicated by the
fuel level indicator needle returning to
zero.
Consult a PEUGEOT dealer.
F u e l w a r n i n g
Turn the cap to the left.
Remove the cap and hang the end
on the hook located on the inside
o f t h e fl a p .
A l a b e l a f fi x e d t o t h e i n s i d e o f t h e f u e l
fi l l e r fl a p i n d i c a t e s w h i c h t y p e o f f u e l
to use.
W h e n y o u fi l l y o u r t a n k , d o n o t c o n -
tinue after the third cut-off of the pump.
This could cause your vehicle to mal-
function.
The capacity of the tank is approxi-
m a t e l y 6 7 l i t r e s .
A f t e r fi l l i n g t h e t a n k , s c r e w o n t h e
c a p a n d c l o s e t h e f u e l fi l l e r fl a p .
E n s u r e t h a t t h e f u e l fi l l e r fl a p i s
closed correctly. When this warning light
comes on in certain driving
conditions and depending
on the engine, the distance
which can be travelled with
the fuel remaining may be
less than 30 miles (50 kilometres).
Note: should you run out of fuel, you
must add at least 6 litres.
Page 83 of 211
5
75
The timed duration must also
be set, via the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
A u t o m a t i c s w i t c h i n g o n o f t h e lights
To switch the function on
or off, use the multifunction
display "Personalisation-
C o n fi g u r a t i o n " menu.
Activation
Deactivation When this function is activa-
ted, the indicator light on the
instrument panel comes on.
When the function is deacti-
vated, the indicator light on the
instrument panel comes on.
Cancellation:
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
M a n u a l " f o l l o w - m e - h o m e " l i g h t i n g
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.
Activation:
switch off the engine,
fl a s h t h e h e a d l a m p s ,
get out of the vehicle and lock it.
Deactivation:
fl a s h t h e h e a d l a m p s a g a i n ,
get out of the vehicle and lock it.
A u t o m a t i c " f o l l o w - m e - h o m e "
lighting
When you leave your vehicle with
the
a u t o m a t i c s w i t c h i n g o n o f t h e l i g h t s
activated , the side lights and dipped
headlamps remain on for the duration
selected when the ignition is switched
off.
To activate or deactivate this func-
tion, pass via the multifunction display
" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
menu.
In foggy weather, the bright-
n e s s s e n s o r c a n d e t e c t s u f fi -
cient light. As a consequence,
the lights will not come on au-
tomatically.
This function is active when the vehi-
cle is supplied to the customer.
If the brightness sensor does not
f u n c t i o n c o r r e c t l y , if the system is
activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.
D a y t i m e l i g h t s *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit
on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually. This warning light comes on
on the instrument panel.
* According to country.
This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.
The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.