ECU PEUGEOT 5008 2010 Owners Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 5008, Model: PEUGEOT 5008 2010Pages: 331, PDF Size: 23.41 MB
Page 84 of 331
80
The electric window controls
remain operational for ap-
proximately 45 seconds after
the ignition is switched off or until the
vehicle is locked after a front door is
opened.
If one of the passenger windows can-
not be operated from the driver's door
control pad, carry out the operation
from the control pad of the passen-
ger door concerned, and vice versa.
ELECTRIC WINDOWS
System intended to open or close a
window manually or automatically.
Fitted with a safety anti-pinch system
and a system for deactivation in the
event of misuse of the rear controls.
1. Driver's electric window control.
2. Passenger's electric window
control.
3. Rear right electric window control.
4. Rear left electric window control.
5. Deactivation of the rear electric
window and door controls. If the window cannot be closed
(for example, in the presence
of ice), immediately after the
movement is reversed:
press and hold the control until
the window opens fully,
then pull the control immediately
and hold it until the window closes,
continue to hold the control for
approximately one second after
the window has closed.
The safety anti-pinch function
is not operational during these
operations.
Safety anti-pinch
When the window rises and meets an
obstacle, it stops and partially lowers
again.
-
automatic mode
P r e s s o r p u l l t h e c o n t r o l fi r m l y .
The window opens or closes fully
when the control is released.
Pressing the control again stops
the movement of the window.
One-touch electric windows
There are two options:
- manual mode
Press or pull the control gently.
The window stops when the control
is released.
After approximately ten con-
secutive complete opening/clos-
ing movements of the window, a
protection function is activated to prevent
damage to the electric window motor.
After this, you have approximately
one minute within which to close the
window.
Once the window is closed, the con-
trols will become available again after
approximately 40 minutes.
Page 91 of 331
86
The key cannot be removed
from the lock until the cap is
put back on the tank.
Opening the cap may trigger an in-
rush of air. This vacuum, which is
completely normal, is caused by the
sealing of the fuel system.
FUEL TANK T o fi l l t h e t a n k s a f e l y :
it is essential that the engine is
switched off,
o p e n t h e f u e l fi l l e r fl a p ,
insert the key in the cap, then turn it
to the left,
When refueling is complete:
put the cap back in place,
turn the key to the right, then remove
it from the cap,
c l o s e t h e fi l l e r fl a p .
remove the cap and secure it on the
hook, located on the inside of the
fl a p ,
fi l l t h e t a n k , b u t do not continue after
the 3rd cut-off of the nozzle ; this could
cause malfunctions.
Low fuel level
Operating fault
A malfunction of the fuel gauge is indi-
cated by the return to zero of the fuel
level indicator needle.
Have it checked by a PEUGEOT dealer.
Refueling
A l a b e l a f fi x e d t o t h e i n s i d e o f t h e fi l l e r
fl a p r e m i n d s y o u o f t h e t y p e o f f u e l t o b e
used according to your engine.
More than 5 litres of fuel must be added in
order to be registered by the fuel gauge. When the fuel tank minimum
level is reached, this warning
lamp comes on on the instru-
ment panel, accompanied by an
audible signal and a message
on the multifunction screen.
W h e n t h e l a m p fi r s t c o m e s o n , y o u h a v e
approximately 6 litres of fuel remaining.
You must refuel to avoid running out of
fuel.
If you run out of fuel (Diesel),
refer also to the "Checks"
section.
Capacity of the tank: approximately
60 litres.
Page 112 of 331
FITTINGS
102
To avoid any risk of jamming
of the pedals:
- only use mats which are s u i t e d t o t h e fi x i n g s a l r e a d y
p r e s e n t i n t h e v e h i c l e ; i t i s
imperative that these are
used,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
MATS
Removable carpet protection. Refitting
T o r e fi t t h e m a t o n t h e d r i v e r ' s s i d e :
position the mat correctly,
r e fi t t h e fi x i n g s b y p r e s s i n g ,
check that the mat is secured correctly.
Fitting
W h e n fi t t i n g t h e m a t f o r t h e fi r s t t i m e ,
o n t h e d r i v e r ' s s i d e u s e o n l y t h e fi x i n g s
provided in the wallet attached.
The other mats are simply placed on
the carpet.
Removal
To remove the mat on the driver's side:
move the seat as far back as possible,
u n c l i p t h e fi x i n g s ,
remove the mat.
REMOVABLE ASHTRAY
Pull the cover to open the ashtray.
To empty it, remove the ashtray by
pulling it upwards.
Page 118 of 331
FITTINGS
102
To avoid any risk of jamming
of the pedals:
- only use mats which are s u i t e d t o t h e fi x i n g s a l r e a d y
p r e s e n t i n t h e v e h i c l e ; i t i s
imperative that these are
used,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
MATS
Removable carpet protection. Refitting
T o r e fi t t h e m a t o n t h e d r i v e r ' s s i d e :
position the mat correctly,
r e fi t t h e fi x i n g s b y p r e s s i n g ,
check that the mat is secured correctly.
Fitting
W h e n fi t t i n g t h e m a t f o r t h e fi r s t t i m e ,
o n t h e d r i v e r ' s s i d e u s e o n l y t h e fi x i n g s
provided in the wallet attached.
The other mats are simply placed on
the carpet.
Removal
To remove the mat on the driver's side:
move the seat as far back as possible,
u n c l i p t h e fi x i n g s ,
remove the mat.
REMOVABLE ASHTRAY
Pull the cover to open the ashtray.
To empty it, remove the ashtray by
pulling it upwards.
Page 124 of 331
FITTINGS
108
Roller load space cover To install the load space cover:
position one of the ends of the roller
in its support,
insert the second end in its support,
pivot the ends of the roller down-
wards to secure it,
reel out the load space cover to the
boot pillars,
insert the load space screen guides
in the rails on the boot pillars.
To remove the load space cover:
remove the load space cover guides
from the rails on the boot pillars,
reel in the load space cover in its
roller,
To store the load space cover, roller
u p p e r m o s t a n d fl a p f a c i n g t o w a r d s t h e
inside of the vehicle:
place the right-hand end in its housing,
slide the left-hand end into the guide
then into its housing,
pivot the ends of the roller upwards
to release it,
remove the roller from its support.
The roller has two rings for
fi x i n g t h e l u g g a g e r e t a i n i n g
net depending on its location.
I f y o u u s e t h e 3 r d r o w s e a t s
(7 seat version), it is essential
to store the roller in its housing.
secure the assembly by pivoting the
ends downwards.
Page 126 of 331
FITTINGS
110
Luggage retaining net
Hooked onto the stowing rings on the
fl o o r a n d / o r o n t h e l o a d s p a c e c o v e r
roller, this enables you to secure your
luggage. There are 4 possible positions:
- fl a t a t t h e b o t t o m o f t h e b o o t ,
- horizontal, level with the load space
cover, - vertical at the back of the rear seats,
- fl a t a t t h e b o t t o m o f t h e b o o t a n d
vertical at the back of the rear seats.
Page 127 of 331
FITTINGS
111
The hooks permit the securing of shop-
ping bags.
Hooks
In order to connect a 12 V accessory
(max power: 120 Watts), remove
the cap and connect the appropriate
adaptor.
Turn the key to the ignition position.
12 V accessories socket
Raise the concertina board to gain
access to the storage box.
D e p e n d i n g o n t h e c o n fi g u r a t i o n , t h i s
has areas for storing:
- a box of spare bulbs,
- a fi r s t a i d k i t ,
- a tyre repair kit,
- two warning triangles,
- ... Storage box (5 seat version)
Page 130 of 331
FITTINGS
108
Roller load space cover To install the load space cover:
position one of the ends of the roller
in its support,
insert the second end in its support,
pivot the ends of the roller down-
wards to secure it,
reel out the load space cover to the
boot pillars,
insert the load space screen guides
in the rails on the boot pillars.
To remove the load space cover:
remove the load space cover guides
from the rails on the boot pillars,
reel in the load space cover in its
roller,
To store the load space cover, roller
u p p e r m o s t a n d fl a p f a c i n g t o w a r d s t h e
inside of the vehicle:
place the right-hand end in its housing,
slide the left-hand end into the guide
then into its housing,
pivot the ends of the roller upwards
to release it,
remove the roller from its support.
The roller has two rings for
fi x i n g t h e l u g g a g e r e t a i n i n g
net depending on its location.
I f y o u u s e t h e 3 r d r o w s e a t s
(7 seat version), it is essential
to store the roller in its housing.
secure the assembly by pivoting the
ends downwards.
Page 132 of 331
FITTINGS
110
Luggage retaining net
Hooked onto the stowing rings on the
fl o o r a n d / o r o n t h e l o a d s p a c e c o v e r
roller, this enables you to secure your
luggage. There are 4 possible positions:
- fl a t a t t h e b o t t o m o f t h e b o o t ,
- horizontal, level with the load space
cover, - vertical at the back of the rear seats,
- fl a t a t t h e b o t t o m o f t h e b o o t a n d
vertical at the back of the rear seats.
Page 133 of 331
FITTINGS
111
The hooks permit the securing of shop-
ping bags.
Hooks
In order to connect a 12 V accessory
(max power: 120 Watts), remove
the cap and connect the appropriate
adaptor.
Turn the key to the ignition position.
12 V accessories socket
Raise the concertina board to gain
access to the storage box.
D e p e n d i n g o n t h e c o n fi g u r a t i o n , t h i s
has areas for storing:
- a box of spare bulbs,
- a fi r s t a i d k i t ,
- a tyre repair kit,
- two warning triangles,
- ... Storage box (5 seat version)