seats PEUGEOT 5008 2013.5 User Guide

Comfort
74
Rigid panel
Each 2 nd row seat backrest has a rigid panel attached. This panel enables you: - to have a continuous load sur face in the boot, whatever the positions of the seats, - to avoid having objects sliding under the 2 nd row seats. 30 kg maximum on each panel.
Releasing/Locking the rigid panel
 Before deploying the rigid panels, check that the 2 nd row seats are positioned as far towards the rear as possible.  Slide the latch E on the panel upwards, to
release it.  Return the panel to its initial position, then slide the latch E downwards, to lock it in place.
Entering/Exiting the 3 rd row
(7 seat version)
Repositioning the seat,
from the outside, with the
door open
If there are passengers seated in the 3 rd row (7 seat version):  Manually return the assembly as far as possible rear wards; the seat does not return as far as the maximum rear wards position so as to retain leg space for the 3 rd row passengers.  Fold the seat base.
 Raise the aircraft style table on the 2 nd row seat if it is down.  Hold the control F in the raised position, the seat unlocks and the seat base comes up against the backrest.  Push the seat backrest for wards, holding the control F forwards.

3
Comfort75
3 rd row seats (7 seat version)
Concertina boards
Two rigid concertina boards, which cannot be separated from the vehicle, cover the two 3 rd row seats, when these are in the folded position.
Folding the concertina boards
 Pull on the control, the 3 sections of the board will fold like a concertina. When the 3 rd row seats are upright, these concertina boards can be left either:
- flat behind the seats, - in the vertical position, thereby leaving a storage area available. The two rigid boards can each support a maximum of 100 kg.
Installing a seat
 Remove the load space screen.  If necessary, return the 2 nd row rigid panels to their initial position and lock them.  Correctly position the concertina board vertically behind the seat.  Pull on the control G , located behind the seat backrest. The backrest tilts rear wards
pulling the seat base with it. The seat locks in the open position.

Comfort
76
Storing a seat
 Lower the head restraints.  Correctly position the concertina board vertically behind the seat.  Pull on the control H , located at the bottom of the seat backrest. The seat is released.  Next push the backrest gently for wards. The backrest pivots folding onto the seat base. The seat base then folds into the stowage area provided for that purpose.  Reposition the concertina boards over the folded seats.
Before moving the 3 rd row seats, return the rigid panels of the 2 nd row seats to the upright position and lock them in place. Do not try to fold a 3 rd row seat that has
not first had the backrest fully locked in place. Do not leave objects either on or underneath the seat bases of the 3 rd row seats when you are folding them. Do not leave your hand on the control H as you fold the seats, as you risk trapping your fingers.

3
Comfort77
Seat modularity and the various seat confi gurations
Examples of configurations
7 seats
Transporting long objects 5 seats
Transport (4 seats)
Loading a large volume
Designed to be modular, your vehicle offers numerous seat installation and loading configurations. Operations to change the existing configuration must only be carried out when stationary (see paragraphs "Rear seats".

4
Access95
Tailgate release
Unlocking
 Fold back the rear seats to gain access to the lock from inside the boot.  Insert a small screwdriver into hole A of the lock to unlock the tailgate.  Move the latch to the left.
Locking after closing
If the fault persists after closing again, the boot will remain locked. System allowing the mechanical unlocking of the boot in the event of a battery or central locking system malfunction.

5
Visibility107
Manual adjustment of halogen headlamps
To avoid causing a nuisance to other road users, the height of the halogen headlamps should be adjusted according to the load in the vehicle. 0. 1 or 2 people in the front seats. -. 3 people. 1. 5 people. -. Intermediate setting. 2. 5 people + maximum authorised load. -. Intermediate setting. 3. Driver + maximum authorised load.
Automatic
adjustment
of the xenon
headlamps
In order to avoid causing a nuisance to other road users, this system corrects the height of the xenon headlamps beam automatically and when stationary, in relation to the load in the vehicle.
If a malfunction occurs, this warning lamp is displayed on the instrument panel, accompanied by an audible signal and a message on the multifunction screen. The system then places your headlamps in the
lowest position.
If a malfunction occurs, do not touch the xenon bulbs. Contact a PEUGEOT
dealer or a qualified workshop.
Travelling abroad
If using your vehicle in a country that drives on the other side of the road, the headlamps must be adjusted to avoid dazzling on-coming drivers. Contact a PEUGEOT dealer or a qualified workshop.
The initial setting is position "0" .

6
Fittings121

Storage compartments
under the rear footwells
Depending on the configuration, the vehicle has storage compartments under the footwells, located for ward of the outer rear seats. Access is via clipped flaps with a handle A .
"Aircraft" type tables
Installed on the back of each front seat, these allow you to set down objects.  To use the table, lower it fully until it locks in the low position.  To store the table, raise it, passing the point of resistance, to the high position.

Storage drawer
It is located under the driver's seat (manual adjustment).
Opening
 Raise the front of the drawer and pull it. Do not place heavy objects in the drawers. On the passenger side, do not forget to fold the "aircraft" type table before placing the seat in the table position. Do not place hard or heavy objects on the table. They could become dangerous projectiles in the event of emergency braking or impact.

6
Fittings127
Roller load space cover
To install the load space cover:  position one of the ends of the roller in its support,  insert the second end in its support,  pivot the ends of the roller downwards to secure it,  reel out the load space cover to the boot pillars,  insert the load space screen guides in the rails on the boot pillars.
To remove the load space cover:  remove the load space cover guides from the rails on the boot pillars,  reel in the load space cover in its roller,
To store the load space cover, roller uppermost and flap facing towards the inside of the vehicle:  place the right-hand end in its housing, slide the left-hand end into the guide then into its housing,
 pivot the ends of the roller upwards to release it,  remove the roller from its support.
 secure the assembly by pivoting the ends downwards. The roller has two rings for fixing the luggage retaining net depending on its location.
If you use the 3 rd row seats (7 seat version), it is essential to store the roller in its housing.

Fittings
128
High load retaining net *
To use it in row 1:  fold the rear seats,  open the covers of the upper fixings 1 ,  unroll the high load retaining net,  position one of the ends of the net's metal bar in the corresponding upper fixing 1 , then do the same with the other end,  slacken the straps fully,  fix the snap hook of each of the straps on the corresponding Top Tether ring 3(located on the back of the folded rear side seats),  tighten the straps,  check that the net is hooked and tightened
c o r r e c t l y.
To use it in row 2:  roll up or remove the load space screen,  open the covers of the upper fixings 2 ,  unroll the high load retaining net,  position one of the ends of the net's metal bar in the corresponding upper fixing 2 , then do the same with the other end,  fix the snap hook of each of the straps in the corresponding stowing ring 4 ,  tighten the straps,  check that the net is hooked and tightened c o r r e c t l y.
Hooked onto the special upper and lower fixings, this permits use of the entire loading volume up to the roof: - behind the front seats (row 1) when the rear seats are folded. - behind the rear seats (row 2).
* If your vehicle is equipped with this.
When positioning the net, check that the strap loops are visible from the boot; this will make slackening or tightening easier.

6
Fittings129
Luggage retaining net
Hooked onto the stowing rings on the floor and/or on the load space cover roller, the luggage retaining net available as an accessory enables you to secure your luggage.
There are 4 possible positions:
- flat at the bottom of the boot,
- horizontal, level with the load space cover,
- vertical at the back of the rear seats,
- flat at the bottom of the boot and vertical at the back of the rear seats.