tow PEUGEOT 5008 2016 User Guide

77
5008_en_Chap03_confort_ed01-2015
Storing a seat
F Lower the head restraints.
F C orrectly position the concertina board
vertically behind the seat.
F

P
ull on the control H , located at the bottom
of the seat backrest. The seat is released.
F

N
ext push the backrest gently for wards.
The backrest pivots folding onto the seat
base. The seat base then folds into the
stowage area provided for that purpose.
F

R
eposition the concertina boards over the
folded seats. Before moving the 3
rd row seats, return
the rigid panels of the 2nd row seats to
the upright position and lock them in
place.
Do not try to fold a 3
rd row seat that has
not first had the backrest fully locked in
place.
Do not leave objects either on or
underneath the seat bases of the
3
rd row seats when you are folding them.
Do not leave your hand on the control H
as you fold the seats, as you risk
trapping your fingers.
Rear head restraints
The rear head restraints can be removed and
have two positions:
-

h
igh, position for use,
-
lo

w, storage position.
To raise a head restraint, pull it upwards.
To lower it, press the lug then the head
restraint.
To remove it, place it in the high position, push
the lug and pull it upwards.
To refit it, engage the head restraint rods in the
holes taking care to remain in line with the seat
back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
3
Comfort

83
5008_en_Chap04_visibilite_ed01-2015
Model without AUTO lighting
Model with AUTO lighting
The lighting is controlled directly by the driver
by means of the ring A and the stalk B.
B.
S

talk for switching headlamps: pull
the stalk towards you to switch the
lighting between dipped and main beam
headlamps.
In the lamps off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining a
pull on the stalk. Automatic illumination of
headlamps. Lighting off (ignition off) /
Daytime running lamps (engine
running).
Sidelamps.
Dipped headlamps or main
beam headlamps.
Displays
Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
Manual controls
A. Main lighting mode selection ring: turn it
to position the symbol required facing the
mark.
4
Visibility

93
5008_en_Chap04_visibilite_ed01-2015
Windscreen wash
Pull the wiper stalk towards you.
The windscreen wash then the wipers operate
for a set time.
The headlamp wash is also activated if the
dipped beam headlamps are on .
Screenwash/headlamp wash low
level
In the case of vehicles fitted with
headlamp washers, when the
minimum level of the reservoir
is reached, this warning lamp is
displayed in the instrument panel, accompanied
by an audible signal and a message.
The warning lamp is displayed when the
ignition is switched on, or every time the stalk is
operated, until the reservoir is refilled.
Next time you stop, refill the screenwash /
headlamp wash reservoir.
Headlamp wash
Press the end of the lighting stalk to activate
the headlamp wash, when the dipped beam
headlamps are on.
4
Visibility

108
5008_en_Chap05_amenagements_ed01-2015
Boot fittings (5-seat version)
1. Load space cover
2.
Hoo
ks
3.
1

2 V accessor y socket (120 W)
4.
S

torage compartment under the floor
5.
C

oncertina boards
6.
S

towing rings on the floor
7.
C

up holder
8.
S

torage compartments or audio
amplifier
Fittings

109
5008_en_Chap05_amenagements_ed01-2015
1. Load space cover
2.
Hoo
ks
3.
1

2 V accessor y socket (120 W)
4.
B

uckles for the 3
rd row seat belts
5.
C

oncertina boards
6.
S

towing rings on the floor
7.
C

up holder
8.
A

rmrests
9.
S

torage compartments or audio
amplifier
Boot fittings (7-seat version)
5
Fittings

110
5008_en_Chap05_amenagements_ed01-2015
Roller load space cover
To install the load space cover:
F p osition one of the ends of the roller in its
support,
F

i
nsert the second end in its support,
F

p
ivot the ends of the roller downwards to
secure it,
F

r
eel out the load space cover to the boot
pillars,
F

i
nsert the load space screen guides in the
rails on the boot pillars.
To remove the load space cover:
F

r

emove the load space cover guides from
the rails on the boot pillars,
F

r

eel in the load space cover in its roller, To store the load space cover, roller uppermost
and flap facing towards the inside of the
vehicle:
F

p

lace the right-hand end in its housing,
F

s

lide the left-hand end into the guide then
into its housing,
F

p

ivot the ends of the roller upwards to
release it,
F

r

emove the roller from its support. F

se

cure the assembly by pivoting the ends
downwards. The roller has two rings for fixing the
luggage retaining net depending on its
location. If you use the 3
rd row seats (7 seat
version), it is essential to store the roller
in its housing.
Fittings

111
5008_en_Chap05_amenagements_ed01-2015
High load retaining
net*
To use it in row 1:
F
f old the rear seats,
F

o
pen the covers of the upper fixings 1 ,
F

u
nroll the high load retaining net,
F

p
osition one of the ends of the net's metal
bar in the corresponding upper fixing 1 ,
then do the same with the other end,
F

s
lacken the straps fully,
F

f
ix the snap hook of each of the straps
on the corresponding Top Tether ring 3
(located on the back of the folded rear side
seats),
F

t
ighten the straps,
F

c
heck that the net is hooked and tightened
c o r r e c t l y. To use it in row 2:
F
r oll up or remove the load space screen,
F

o
pen the covers of the upper fixings 2,
F

u
nroll the high load retaining net,
F

p
osition one of the ends of the net's metal
bar in the corresponding upper fixing 2 ,
then do the same with the other end,
F

f
ix the snap hook of each of the straps in
the corresponding stowing ring 4 ,
F

t
ighten the straps,
F

c
heck that the net is hooked and tightened
c o r r e c t l y.
Hooked onto the special upper and lower
fixings, this permits use of the entire loading
volume up to the roof:
-

b

ehind the front seats (row 1) when the
rear seats are folded.
-

b

ehind the rear seats (row 2).
* If your vehicle is equipped with this.
When positioning the net, check that
the strap loops are visible from the
boot; this will make slackening or
tightening easier.
5
Fittings

112
5008_en_Chap05_amenagements_ed01-2015
Luggage retaining net
Hooked onto the stowing rings on the floor and/
or on the load space cover roller, the luggage
retaining net available as an accessory enables
you to secure your luggage.There are 4 possible positions:
-

f
lat at the bottom of the boot,
-

h
orizontal, level with the load space cover,-

v
ertical at the back of the rear seats,
-

f
lat at the bottom of the boot and vertical at
the back of the rear seats.
Fittings

124
5008_en_Chap06_securite-enfants_ed01-2015
Remove and stow the head restraint
before installing a child seat with
backrest on a passenger seating
position. Refit the head restraint when
the child seat is removed.
a:

u
niversal child seat, child seat that can be
installed in all vehicles using a seat belt.
b:

g

roup 0, from birth to 10 kg. Shells seats and
baby carriers cannot be installed in the front
passenger seat.
c:

c

onsult the legislation in force in your
country before installing your child on this
seat.
d:

t

o install a child seat on a rear seat,
rear ward facing or for ward facing, move
the front seat for ward, then straighten the
backrest to allow enough space for the child
seat and the child's legs.
e:

t

o install a child seat on a rear seat, rear ward
facing or for ward facing, adjust the rear seat
to the fully back position, with the backrest
upright. U:

s
eat suitable for the installation of a
child seat secured using a seat belt and
universally approved, rear ward facing and/or
forward facing.
U (R):

s

ame as U , with the vehicle's seat
adjusted to the highest position.
L-:

o

nly the child seats indicated can be
installed on the seat concerned (according
to local legislation).
X:

s

eat position not suitable for installation of a
child seat for the weight class indicated.
Child safety

126
5008_en_Chap06_securite-enfants_ed01-2015
a: universal child seat, child seat that can be
installed in all vehicles using a seat belt.
b:

g
roup 0, from birth to 10 kg. Shells seats and
baby carriers cannot be installed in the front
passenger seat.
c:

c
onsult the legislation in force in your
country before installing your child on
this


seat.
d:

T
o install a child seat on a rear seat,
rear ward facing or for ward facing, move
the front seat for ward, then straighten the
backrest to allow enough space for the child
seat and the child's legs.
e:

T
o install a child seat on a rear seat,
rearward facing or forward facing, adjust the
rear seat to the fully back position, with the
backrest upright. Remove and stow the head restraint
before installing a child seat on a
passenger seat. Refit the head restraint
once the child seat has been removed.
U:
s eat suitable for the installation of a
child seat secured using a seat belt and
universally approved, rear ward facing and/or
forward facing.
U (R):

s
ame as U, with the vehicle's seat
adjusted to the highest position.
L-:

o
nly the child seats indicated can be
installed on the seat concerned (according
to local legislation).
X:

s
eat position not suitable for installation of a
child seat for the weight class indicated.
Child safety