display PEUGEOT 508 2010 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2010, Model line: 508, Model: PEUGEOT 508 2010Pages: 330, PDF Size: 11.68 MB
Page 36 of 330
36
Instruments and controls
System which provides current information concerning the trip (range, consumption…).
Trip computer
Instrument panel screen
Information display
ï† Press the button, located at the end of the wiper stalk , to display the various trip computer tabs in succession.
- The current information tab with:
Page 37 of 330
137
i
i
i
Instruments and controls
If dashes are displayed continuously
while driving in place of the digits, contact a PEUGEOT dealer or a qualified workshop.
This function is only displayed from 20 mph (30 km/h).
This value may vary following a change in the style of driving or the relief, resulting in a significant change in the current fuel consumption.
A few definitions…
Range
(miles or km) This indicates the distance which can still be travelled with the fuel remaining in the tank
in relation to the average fuel consumption over the last few miles (kilometres) travelled.
When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is displayed when it exceeds 60 miles (100 km).
Current fuel consumption
(mpg or l/100 km or km/l) This is the average fuel consumption during the last few seconds.
Average fuel consumption
(mpg or l/100 km or km/l) This is the average fuel consumption since the last trip computer zero reset.
Average speed
(mph or km/h) This is the average speed calculated since the last trip computer zero reset (ignition on).
Trip reset
ï† When the trip required is displayed, press the control for more than two seconds or use the left hand thumbwheel of the steering mounted controls. Trips "1" and "2" are independent but their use is identical. For example, trip "1" can be used for daily
figures, and trip "2" for monthly figures.
Page 46 of 330
46
Access
Changing the battery of the key
Battery ref.: CR2032/3 volts. This replacement battery is available from a PEUGEOT dealer or a qualified workshop. A message appears in the instrument panel screen when replacement of the battery is needed. ï† Unclip the cover using a small screwdriver at the cutout. ï† Lift off the cover.
ï† Remove the flat battery from its location. ï† Fit the new battery into its location obser ving the original direction of fitment. ï† Clip the cover onto the casing.
Do not throw the remote control batteries away, they contain metals which are harmful to the environment. Take them to an approved collection point.
Reinitialisation with the electronic key
ï† Switch of the ignition. ï† Immediately press one of the remote control buttons for a few seconds. ï† Switch on the ignition. The electronic key is fully operational again.
Changing the battery of the electronic key
Battery ref.: CR2032/3 volts. This replacement battery is available from a PEUGEOT dealer or a qualified workshop. A message is displayed in the instrument panel screen when replacement of the battery is needed. ï† Unclip the cover using a pointed object at the key ring. ï† Slide the flat battery out of its location.
ï† Slide the new battery into its location obser ving the original direction of fitment. ï† Clip the cover in place star ting at the front. ï† Reinitialise the electronic key.
Page 54 of 330
46
Access
Changing the battery of the key
Battery ref.: CR2032/3 volts. This replacement battery is available from a PEUGEOT dealer or a qualified workshop. A message appears in the instrument panel screen when replacement of the battery is needed. ï† Unclip the cover using a small screwdriver at the cutout. ï† Lift off the cover.
ï† Remove the flat battery from its location. ï† Fit the new battery into its location obser ving the original direction of fitment. ï† Clip the cover onto the casing.
Do not throw the remote control batteries away, they contain metals which are harmful to the environment. Take them to an approved collection point.
Reinitialisation with the electronic key
ï† Switch of the ignition. ï† Immediately press one of the remote control buttons for a few seconds. ï† Switch on the ignition. The electronic key is fully operational again.
Changing the battery of the electronic key
Battery ref.: CR2032/3 volts. This replacement battery is available from a PEUGEOT dealer or a qualified workshop. A message is displayed in the instrument panel screen when replacement of the battery is needed. ï† Unclip the cover using a pointed object at the key ring. ï† Slide the flat battery out of its location.
ï† Slide the new battery into its location obser ving the original direction of fitment. ï† Clip the cover in place star ting at the front. ï† Reinitialise the electronic key.
Page 55 of 330
46
Access
Changing the battery of the key
Battery ref.: CR2032/3 volts. This replacement battery is available from a PEUGEOT dealer or a qualified workshop. A message appears in the instrument panel screen when replacement of the battery is needed. ï† Unclip the cover using a small screwdriver at the cutout. ï† Lift off the cover.
ï† Remove the flat battery from its location. ï† Fit the new battery into its location obser ving the original direction of fitment. ï† Clip the cover onto the casing.
Do not throw the remote control batteries away, they contain metals which are harmful to the environment. Take them to an approved collection point.
Reinitialisation with the electronic key
ï† Switch of the ignition. ï† Immediately press one of the remote control buttons for a few seconds. ï† Switch on the ignition. The electronic key is fully operational again.
Changing the battery of the electronic key
Battery ref.: CR2032/3 volts. This replacement battery is available from a PEUGEOT dealer or a qualified workshop. A message is displayed in the instrument panel screen when replacement of the battery is needed. ï† Unclip the cover using a pointed object at the key ring. ï† Slide the flat battery out of its location.
ï† Slide the new battery into its location obser ving the original direction of fitment. ï† Clip the cover in place star ting at the front. ï† Reinitialise the electronic key.
Page 63 of 330
255
Access
Emergency release
(Saloon and SW)
System for mechanical unlocking of the boot in the event of a battery or central locking fault.
Unlocking
ï† Fold back the rear seats to gain access to the lock from inside the boot. ï† Inser t a small screwdriver into hole A of the
lock to unlock the tailgate.
"Boot open" warning
With the engine running or when the vehicle is moving, if the tailgate is not properly closed, a message accompanied by an audible signal (from 6 mph (10 km/h)) is displayed in the instrument panel screen.
Page 71 of 330
363
Comfort
Storing driving positions
System which stores the electrical settings of the driver's seat and door mirrors as well as the head-up display settings. It enables you to store up to two positions using the buttons on the side of the driver's seat.
Storing a position
using buttons M/1/2
ï† Switch on the ignition. ï† Adjust your seat, the door mirrors and the head-up display. ï† Press button M , then press button 1 or 2within four seconds. An audible signal indicates that the position has been stored. Storing a new position cancels the previous position.
Recalling a stored position
Ignition on or engine running
ï† Briefly press button 1 or 2 to recall the corresponding position. An audible signal indicates the end of the
adjustment. You can interrupt the current movement by pressing button M , 1 or 2 or by using one of the seat controls. A stored position cannot be recalled while driving. Recalling stored positions is deactivated 45 seconds after switching off the ignition.
Welcome function
The welcome function assists entry and leaving the vehicle. After switching off the ignition and opening the driver’s door, the seat moves back automatically and then stays in this position, ready for the next entry to the vehicle. When switching on the ignition, the seat moves for ward to the stored driving position. When moving the seat, take care that no person or object hinders the automatic movement of the seat. To activate or deactivate this function, contact a PEUGEOT or a qualified workshop.
Page 81 of 330
373
i
Comfort
Peugeot Connect USB
auxiliary socket and a USB por t, is located in the front armrest (under the cover). It permits the connection of por table device, such as a digital audio player of the iPod ® type ®
or a USB memory stick.
It reads the audio file formats (MP3, OGG, WMA, WAV, ...) which are transmitted to your audio equipment and played via the vehicle's
speakers. You can manage these files using the steering mounted controls or the audio system control panel and display them in the instrument panel screen.
When the USB por t is used, the por table device charges automatically.
For more information on the use of this system, refer to the "Audio and
Telematics" section.
Ski flap
Device for storing and transpor ting long objects.
Opening
ï† Lower the armrest. ï† Press the flap opening control. ï† Lower the flap. ï† Load the objects from inside the boot.
Page 83 of 330
373
i
Comfort
Peugeot Connect USB
auxiliary socket and a USB por t, is located in the front armrest (under the cover). It permits the connection of por table device, such as a digital audio player of the iPod ® type ®
or a USB memory stick.
It reads the audio file formats (MP3, OGG, WMA, WAV, ...) which are transmitted to your audio equipment and played via the vehicle's
speakers. You can manage these files using the steering mounted controls or the audio system control panel and display them in the instrument panel screen.
When the USB por t is used, the por table device charges automatically.
For more information on the use of this system, refer to the "Audio and
Telematics" section.
Ski flap
Device for storing and transpor ting long objects.
Opening
ï† Lower the armrest. ï† Press the flap opening control. ï† Lower the flap. ï† Load the objects from inside the boot.
Page 94 of 330
84
i
Comfort
Dual-zone digital air conditioning
The air conditioning system operates when the engine is running.
Automatic operation
1. Automatic comfort programme
ï† Press this "AUTO" button. The indicator lamp comes on.
We recommend that you use this mode. It
automatically adjusts all settings to provide optimum operation for the comfor t level chosen: passenger compar tment temperature, air flow, air distribution and air recirculation. This system is designed to operate effectively in all seasons, with the windows closed.
When the engine is cold, to prevent too great a distribution of cold air, the air flow will reach its optimum level gradually. In cold weather, it favours the distribution of warm air to the windscreen, side windows and footwells only.
2 - 3. Driver-passenger side adjustment
The driver and front passenger can each adjust the temperature to their requirements. The value indicated on the display corresponds to a level of comfor t and not to a temperature in degrees Celsius or Fahrenheit.
ï† Turn control 2 or 3 to the left (blue) or to the right (red) respectively to decrease or increase this value.
A setting around the value 21 provides optimum comfort. However, depending on your requirements,
a setting between 18 and 24 is normal. It is recommended that the difference between left and right should not be greater 3.