seats Peugeot 508 Dag 2010.5 Owner's Manual

.
9
Familiarisation
Sitting comfortably
Front seats
61
Manual adjustments
1. Head restraint height and angle adjustment. 2. Backrest angle adjustment. 3. Seat cushion height adjustment. 4. Lumbar suppor t adjustment. 5. Seat for wards-backwards adjustment. 6. Cushion adjustment.
Electrical adjustment
1. Angle, seat height and seat for wards-backwards adjustment.
2. Backrest angle adjustment. 3. Lumbar suppor t adjustment.
62

12
!
Familiarisation
Sitting comfortably
Head restraint adjustment
64
1. Release the adjustment mechanism. 2. Adjust for height and reach. 3. Lock the adjustment mechanism.
Steering wheel adjustment
70
For reasons of safety, these operations must only be carried out with the vehicle stationary.
Heated seats control
0 : off. 1 : low. 2 : medium. 3 : high.
To lower it, press button A . To raise it, guide the head restraint upwards to the desired position. To incline it, swivel the lower par t backwards or for wards.
64

255
Access
Emergency release
(Saloon and SW)
System for mechanical unlocking of the boot in the event of a battery or central locking fault.
Unlocking
 Fold back the rear seats to gain access to the lock from inside the boot.  Inser t a small screwdriver into hole A of the
lock to unlock the tailgate.
"Boot open" warning
With the engine running or when the vehicle is moving, if the tailgate is not properly closed, a message accompanied by an audible signal (from 6 mph (10 km/h)) is displayed in the instrument panel screen.

361
Comfort
Front seats
Manual adjustments
1. Adjustments to the height and angle of the head restraint To raise it, pull upwards. To lower it, hold the button in and press on the head restraint (pushing to go past the stiff point of the button).
2. Adjustment of the backrest angle Operate the control lever and adjust the position of the backrest to the front or to the rear. 3. Adjustment of the seat height Raise or lower the control lever the number of times required to obtain the desired position. 4. Adjustment of the lumbar suppor t This system allows the height and depth of the lumbar suppor t to be adjusted separately.  For wards or backwards to increase or decrease the lumbar suppor t.  Upwards or downwards to raise or lower the lumbar contact zone. 5. For wards-backwards adjustment of the seat position Lift the control bar and slide the seat
for wards or backwards. 6. Adjustment of the seat cushion Pull on the grip to adjust the length of the cushion.

64
!
Comfort
Head restraint height and angle adjustment
 To lower the head restraint, press the lug A and, going beyond the stiff point, guide the head restraint downwards, then release the button at the desired position.  To raise the head restraint, guide it upwards to the desired position.  To adjust the angle of the head restraint, tilt its lower par t for wards or rear wards.  To remove the head restraint, press the two lugs B and pull the head restraint upwards.
 To put the head restraint back in place, engage the head restraint stems in the openings keeping them in line with the seat back. Check that it has engaged by puling it upwards.
The head restraint is fitted with a locking mechanism which prevents it from lowering; this is a safety device in case of impact. The adjustment is correct when the upper edge of the head restraint is level with the top of the head. Never drive with the head restraints
removed; they must be in place and adjusted correctly.
Heated seats control
With the engine running, the front seats can be heated separately.  Use the adjustment dial, placed on the centre console, to switch on and select the level of heating required: 0: Off. 1: Low. 2: Medium. 3: High.

66
!
Comfort
Rear seats
Bench seat the left-hand (1/3) or right-hand (2/3) section of which can be folded to adapt the boot load space.
Rear head restraints
These have a high position (comfor t and safety) and a low position (rear visibility).
They can also be removed. To remove a head restraint:  pull the head restraint fully upwards,  then, press the lug A .
Never drive with rear passengers when
the head restraints are removed; the head restraints must be in place and in the high position.
Folding the seat from the
boot (SW)
Each section of the bench seat (1/3 or 2/3) has its own control to release the seat back and its seat cushion from the boot.
 Check that nothing is preventing the seat back from folding (head restraint, seat belts, ...),  check also that no object on or under the
seat could hinder its movement,
 pull the control from the boot and push the seat backrest.

375
Comfort

Boot fi ttings (SW)
1. Boot lamps2. Rear seats folding controls3. Retractable hooks4. 12 V accessor y socket (120 W max)5. Storagetrays With towing eye, a wheel chock and a temporary puncture repair kit (according to destination country and equipment). 6. Stowing rings7. Load space cover (see following page)
8. Boot floor For access to the storage compartments or the spare wheel (according to destination country), position the floor vertically in its guide.

78
i
Comfort
High load retaining net (SW)
Hooked onto the special upper and lower fixings, this allows the use of the entire loading volume up to the roof: - behind the front seats (row 1) when the rear seats are folded. - behind the rear seats (row 2).
Never reposition the rear seats if the net's roller is attached to the backs of the folded seats.  position the net's roller above the two rails (located on the back of the folded rear seats),
 the two grooves a must be placed above the two rails b . Slide the two rails b in the grooves a and push the roller (lengthwise) from right to left to secure it,  check that the net is hooked and tightened correctly,
 fold the rear seats,  unroll the high load retaining net without stretching it,
 position one of the ends of the net's metal bar in the corresponding upper fixing 1 ,  pull the net's metal bar to position the other end in the other upper fixing 1 .
Row 1

5
137
i
!
Visibility
Manual adjustment
of halogen
headlamps Automatic adjustment of xenon headlamps
To avoid causing a nuisance to other road users, the height of the halogen headlamps should be adjusted according to the load in the vehicle. 0. 1 or 2 people in the front seats. -. 3 people. 1. 5 people. -. Intermediate setting. 2. 5 people + maximum authorised load. -. Intermediate setting. 3. Driver + maximum authorised load.
The initial setting is position "0" .
If a fault occurs, this warning lamp is displayed in the instrument panel, accompanied by an audible signal and a message in the instrument panel screen. The system then places your headlamps in the lowest position.
In order to avoid causing a nuisance to other road users, this system corrects the height of the xenon headlamps beam automatically and when stationary, in relation to the load in the vehicle.

If a fault occurs, do not touch the xenon bulbs. Contact a PEUGEOT dealer or a qualified workshop.

146
i
Child safety
General points relating to child seats
following recommendations: - in accordance with European regulations, all children under the age of 12 or less than one and a half metres tall must travel in approved child seats suited to their weight , on seats fitted with a seat belt or ISOFIX mountings * , - statistically, the safest seats in your vehicle for carr ying children are the rear seats, - a child weighing less than 9 kg must travel in the "rear wards-facing" position both in the front and in the rear.
PEUGEOT recommends that children should travel in the rear seats of your vehicle: - "rearwards-facing" up to the age of 2, - "forwards-facing" over the age of 2.
Although one of PEUGEOT's main criteria when designing your vehicle, the safety of your children also depends on you.
* The rules for carrying children are specific to each country. Refer to the current legislation in your country.