instrument panel PEUGEOT 607 2003 Owners Manual

10-02-2003
YOUR AT A GLANCE5
STARTING
STOP position:
The ignition is switched off.
1st notch, Accessories position:The ignition is switched off butthe accessories still function. 2nd notch, Running position: The ignition is on. Starting position:
Operates the starter. Starting a diesel engine If the temperature is highenough, the pre-heat indi- cator light does not comeon and you can start
immediately.
If the indicator light comes on,wait for it to go out before operat-
ing the starter. If the engine stalls, it is neces- sary to return the key to the'Stop' position before re-starting. CHECK
(vehicle autotest)
Automatic check
With the ignition on (2nd notch)
If no malfunction has been detected: In the absence of
vehicle function status indi-cator lights, the OK light is
displayed after two seconds
on the instrument panel screen.Otherwise, it will be displayed afterthese indicator lights come on.
If a 'minor' malfunction has beendetected: the warning light for the
faulty function is displayed on theinstrument panel screen. Certainindicator lights showing the status ofvehicle functions may also come on,followed by the OKindicator light.
If a 'major' malfunction has beendetected: the corresponding warn-
ing light is displayed on the instru-ment panel screen. Certain indicatorlights showing the status of vehicle
functions may also come on. TheOK indicator light does not come
on. Do not start your vehicle.
Contact a PEUGEOT dealer. Afterwards, if the passenger airbag is disarmed, the correspondingwarning light will come on.
With the engine running or if the vehicle is moving, the instrument
panel screen temporarily displays:
Ð lights indicating warnings, when
these occur,
Ð vehicle function sta- tus indicator lights, when a changeoccurs.
The display of certain indicatorlights is accompanied by an audi-ble signal and a message on the
multi-function display. Manual check  Press the "CHECK" button on the
instrument panel.
With the ignition key in the accessories position, with the ignition switched on,with the engine running or the vehiclemoving, this function informs you at alltimes of the following:
Ð any current warnings,
Ð the status of functions which it is possible to switch on or switch off (windscreen wipers, automaticswitching on of lights, cruise con-trol, disarming of passenger airbag, etc.).
The corresponding warning lights aredisplayed in succession on the instru-ment panel screen. If a warning or a change of status occurs during the CHECKmode, the
corresponding indicator light(s) will bedisplayed at the end of this mode.
31
Never run the engine in a confined space.
Do not make any modi-fications to the steeringlock.

10-02-2003
YOUR AT A GLANCE6
STEERING WHEEL
STALKS LIGHTS
Front and rear lights (ring A)
Lights off. Side lights.
Dipped / main beam headlamps. Front and rear fog lamps(ring B)
Front fog lamps. Neutral position of the ring. Rear fog lamps.
Parking lights
To switch on the parking lights on
the traffic side, with the engine
off, place the direction indicator
lights stalk on the traffic side.
Automatic switching on of lights
This occurs if the light is poor, as well as in cases of continuous operation of the windscreen wipers, and stops as soon as the light has becomebright enough or the windscreen wipers have stopped.  To activate or disarm the function, place the key in the accessories position (1st notch), place the lights stalk in position 0and press the
end of the stalk for more than two seconds.
Do not cover the sunshine / brightness sensor located in the centre of the fascia. It helps to regulate the air condi-tioning, the automatic switching on of the lights and theautomatic adjustment of the instrument panel bright-ness. Windsreen wipers 3
Rapid wipe
2 Normal wipe
1 Automatic wipe
0 Off
Automatic wipe In position 1, the wipers operate
automatically and adjust their speed to the intensity of the rain-fall. When the ignition has been
switched off for more than oneminute with the control in a wipeposition, it is necessary to reacti-vate this function.
To do this, move the control to any position, then return to therequired position.
11 711 9

10-02-2003
YOUR AT A GLANCE10
AUTOMATIC GEARBOX 'PORSCHE TIPTRONIC system'
The four speed automaticgearbox offers a choice between the comfort
of integral automatic operation, enhanced by a sport programme and
a snow programme, or the pleasure of manual gear changing.
Gear selection gate  Move the lever in the gate to select one of the functions.Once the function is selected, the indicator light for that function is dis- played on the instrument panel screen.
S: sport programme.
$ : snow programme.
P ark: to immobilise the vehicle and to start the
engine, with the handbrake on or owff.
R everse: to engage reverse; select this function
with the vehicle stationary and the engine at idle. N eutral: to start the engine and to park, with the
handbrake on. Note : if position Nis engaged by mistake while
the car is moving, allow the engine to return to idling speed before engaging function Dto accel-
erate. D rive: for automatic gear changing.
M anual: for manualgear changing.
To change the four gears manually:
 Push the lever to the +symbol to change up to
the next gear and pull it towards the -symbol to
change down a gear.
Note: the S (sport) and
$(
snow) programmes do
not operate in manual mode.
Moving Off With the engine running, to move
off from position P:
 it is essential to press the
brake pedal to exit position P,
 select function R, D or M, then
gradually release the pressureon the brake pedal; the vehi-
cle will move off immediately.
You can also move off from posi-tion N:
 release the handbrake, withyour foot on the brake,
 select function R, D or M, then
gradually release the pressureon the brake pedal; the vehi-
cle will move off immediately.
WARNING When the engine is idling with the brakes not applied, if functionR , D or M is selected, the vehicle
moves without the acceleratorbeing pressed. For this reason, do not leave
children unsupervised inside the vehicle, with the enginerunning. When maintenance operations have to be carried out with theengine running, apply the hand-brake and select position P.
131

10-02-2003
No. Symbol Function1 Air conditioning
on/off.
2 Front visibility
programme.
3 Air intake
control.
4 Rear screen
demisting.
5 Switching
off.
6Passenger setting
7 Passenger comfort
programme.
8 Passenger air distribution
setting.
9 Air flow
adjustment.
10 Driver air distribution
setting.
11 Driver comfort
programme.
12 Driver setting.
12YOUR AT A GLANCE
AUTOMATIC AIR CONDITIONING Do not cover the sunshine / brightness sensor located in the centre of the fascia. It helps to regulate the air conditioning, automatic switching on of the lights and the automatic adjust-ment of the instrument panel brightness.
96

10-02-2003
INSTRUMENTS AND CONTROLS
28
1 -
Handbrake indicator light.
2 - Main beam headlamps indicator light.
3 - Dipped beam headlamps indicator light.
4 - Rev counter.
5 - Left-hand direction indicator.
6 - Fuel gauge.
7 - Right-hand direction indicator.
8 - Speedometer. 9 -
Front fog lamps indicator light.
10 - ABS anti-lock braking system warning light.
11 - Rear fog lamps indicator light.
12 - Engine diagnostics warninglight.
13 - Coolant temperature indicator.
14 - CHECK button.
15 - Trip recorder zero re-set.
16 - Service indicator and total
distance recorder. 17 -
Warning/status screen.
18 - Illumination button +.
19 - Illumination button -.
20 - Engine oil level indicator.
- Engine oil temperature
indicator.
INSTRUMENT PANEL DIALS: PETROL

10-02-2003
INSTRUMENTS AND CONTROLS29
1 -
Handbrake indicator light.
2 - Main beam headlamps indicator light.
3 - Dipped beam headlamps indicator light.
4 - Rev counter.
5 - Left-hand direction indicator.
6 - Fuel gauge.
7 - Right-hand direction indicator.
8 - Speedometer. 9 -
Front fog lamps indicator light.
10 - ABS anti-lock braking system warning light.
11 - Rear fog lamps indicator light.
12 - Engine diagnostics warninglight.
13 - Coolant temperature indicator.
14 - CHECK button.
15 - Trip recorder zero re-set.
16 - Service indicator and total
distance recorder. 17 -
Warning/status screen.
18 - Illumination button +.
19 - Illumination button -.
20 - Engine oil level indicator.
- Engine oil temperature
indicator.
INSTRUMENT PANEL DIALS: DIESEL

10-02-2003
INSTRUMENTS AND CONTROLS
30
INDICATOR LIGHTS
With the key in the accessories position (1st notch): the battery charge warning light illuminates on the instrument panel disp lay.
With the ignition on (2nd notch): the following three warning lights illuminate on the sides of the instrument panel:
Brake fluid level and brake force distribution fault warning light. This light should go out after 3 seconds.If the warning light remains on, or if it comes on when the engine is running and the vehicle is moving, it indicates an excessive drop in the brake fluid level or a malfunction of the brake force distribution.
Stop immediately. Contact a PEUGEOT dealer.
Anti-lock braking system (ABS) warning light This should go out after 3 seconds.
If the warning light remains on or comes on above 8 mph (12 km/h), this indicates a malfunction of the ABS.
However, the vehicle retains conventional servo-assisted braking.
Contact a PEUGEOT dealer.
Engine diagnostics warning lightThis should go out 3 seconds after the engine starts.
If it flashes with the engine running, this indicates a malfunction in the injection or the ignition system. There is a risk of damage to the catalytic converter (petrol engine only).
If it is on continuously, this indicates a fault in the emission control system.
Contact a PEUGEOT dealer as soon as possible.
At the same time, on the instrument panel display:
If no malfunction has been detected: the OK light comes on after two seconds (following a black screen), in the
absence of indicator lights showing the status of vehicle functions. If these indicator lights are present, the OKbut-
ton will come on after these. You may start your vehicle.
If a 'minor' malfunction has been detected: the warning light for the faulty function comes on. Certain indicator
lights showing the status of vehicle functions may also come on, followed by the OKindicator light. You can start
your vehicle; however, contact a PEUGEOT dealer as soon as possible.
If a 'major' malfunction has been detected: the corresponding warning light comes on. Certain indicator lights showing
the status of vehicle functions may also come on. The OKindicator light does not come on. Do not start your vehicle.
Contact a PEUGEOT dealer. Afterwards, if the passenger air bag is disarmed, the corresponding indicator light will come on.

10-02-2003
INSTRUMENTS AND CONTROLS31
Coolant temperature warning light This symbol is accompanied by an audible signal and the message 'Engine temperature too high' on the multi-function display.
It is linked to the STOPwarning light. Stop immediately.
Warning: wait for the engine to cool.
If necessary, top up the level.
With the engine running and the vehicle moving The instrument panel display temporarily shows:
Ð lights indicating warnings, when these occur,Ð vehicle function status indicator lights, when a change occurs.Certain warning lights may be accompanied by an audible signal and a
message on the multi-function display. List of warning symbols MANUAL CHECK (vehicle autotest)
 Press the "CHECK" button on the
instrument panel.
With the ignition key in the acces-sories position, with the ignitionswitched on, with the engine runningor when the vehicle is moving, thisfunction informs you at all times ofthe following: Ð any current warnings,
Ð the status of functions which it is possible to switch on or off (wind- screen wipers, automatic switch-ing on of lights, cruise control, dis-arming of passenger air bag, etc.).
The corresponding warning lightsare displayed in succession on theinstrument panel screen. If a warning or a change of status occurs during the CHECKmode, the
corresponding indicator lights will bedisplayed at the end of this mode.
CHECK mode entry indi-cator light (vehicleautotest) This comes on when you press the 'CHECK' button.
CHECK mode exit indica-tor light (vehicle autotest) This comes on at the end of the CHECK mode.
Engine oil pressure warning light This symbol is accompanied by an audible signal and the message 'Insufficient engine oil pressure' or 'Engine oil level low' on the
multi-function display.
It is linked to the STOPwarning light.
Stop immediately if this comes on when the engine is running.
If there is a lack of oil in the lubrication circuit, top up the level.
Contact a PEUGEOT dealer as soon as possible.
Puncture warning light This symbol comes on accompanied by an audible signal and the mes- sage 'Punctured tyre(s) detected' on the multi-function display.
It is linked to the STOPwarning light. Stop immediately.
Change the damaged wheel.
Have it repaired by a PEUGEOT dealer.

10-02-2003
INSTRUMENTS AND CONTROLS
32
STOP warning light This comes on after the engine oil pressure, coolant temperature orpuncture warning lights, to which it is linked.
Stop immediately. Contact a PEUGEOT dealer.
Brake fluid level and brake force distribution fault warning light This is linked to the light on the instrument panel.Display of this warning light accompaned by an audible signal and the message 'Brake fluid low'indicates an
excessive drop in the brake fluid level.
Display of this warning light, accompanied by an audible signal and the message 'Braking system faulty' on the multi-func-
tion display indicates a malfunction of the brake force distribution system.Stop immediately in both cases. Contact a PEUGEOT dealer.
Dynamic stability control (ESP/ASR) warning light Display of this warning light, accompanied by an audible signal and the message 'ESP/ASR system faulty'on the
multi-function display indicates a system malfunction.
Contact a PEUGEOT dealer.
Handbrake warning light Display of this warning light, accompanied by an audible signal (vehicle moving) and the message 'Handbrake on'
on the multi-function display, indicates that the handbrake is applied or has not been released correctly. Battery charge warning light This comes on each time the ignition key is in the accessories position (1st notch).Display of this warning light when the engine is running is accompanied by an audible signal and the message 'Bat-
tery charge fault' on the multi-function display.
This can indicate:Ð faulty operation of the charging circuit,
Ð loose battery or starter terminals,Ð a cut or slack alternator belt,Ð an alternator fault.
Contact a PEUGEOT dealer.

10-02-2003
INSTRUMENTS AND CONTROLS35
Engine diagnostics warning light This is linked to the warning light on the instrument panel.Display of this warning light is accompanied by an audible signal and the message
'Engine emission control sys-
tem faulty' on the multi-function display.
If it flashes when the engine is running, this indicates a malfunction in the injection, ignition or emission control system. Th ere
is a risk of damage to the catalytic converter (petrol engine only).
Contact a PEUGEOT dealer as soon as possible.
Bulb blown warning lightDisplay of this indicator light is accompanied by an audible signal and the message 'Bulb... faulty' on the multi-func-
tion display, indicating the faulty bulb: a bulb in the dipped beam lights, the side lights, the direction indicator lights (except side repeaters) or the brake lights (except the central brake light).
Change the faulty bulb.
Windscreen/headlamp wash reservoir warning light Display of this warning light is accompanied by an audible signal and the message 'Screenwash low'on the multi-
function display.Fill the windscreen/headlamp wash reservoir the next time you stop. Particulate emission filter saturation warning light (diesel engine) Display of this warning light is accompanied by an audible signal. When it occurs with the engine running, this indicates the start of saturation of the particulate emission filter (excep- tionally long periods of town type driving conditions: reduced speed, long tailbacks...).
To regenerate the filter, you are advised to drive as soon as possible and when traffic conditions permit at a speed of 35 mph(60 km/h) or more for at least five minutes (until the warning light goes out).
If the light remains on, contact a PEUGEOT dealer.Note: After prolonged operation of the vehicle at a very low speed or at idle, you may sometimes notice steam coming from
the exhaust during acceleration. This has no effect on the performance of the vehicle or on the environment.