brake PEUGEOT 807 2002 Owner's Manual

PRACTICAL INFORMATION
140
Only use products
approved by PEUGEOT.
To ensure best perfor
mance from components
as important as the
power steering and the braking
system,
PEUGEOT selects and offers
quite specific products.
CHECK ...
Battery
At the start of winter, have your bat
tery checked by a PEUGEOT dealer.
Air filter and pollen filter
Have the filter elements replaced
regularly. If you drive in dusty con
ditions, change them twice as
often.
Brake pads
Brake pad wear depends on the
style of driving, in particular for vehi
cles which are used in town, over
short distances .
It may be necessary to check the
thickness of the pads, even between
services.
Handbrake
Where the handbrake travel is too
great or there is a reduction in the
performance of the system, the
handbrake should be adjusted, even
between services. Have the system
checked by a PEUGEOT dealer. Fuel supply cutoff
In a serious collision, a mechanism
automatically prevents fuel from
reaching the engine.
The flashing of this warning
light is accompanied by the
message "Fuel circuit dis
armed" on the multi–func
tion display.
To reestablish the fuel supply :  switch off the ignition.
 remove the key.
 check that there is no odour or
leakage of fuel outside the vehi
cle.
 put the key back in the ignition
 switch on the ignition and start.
Manual gearbox
This does not need an oil change.
Check the level, according to the
manufacturer's service schedule.
Automatic gearbox
This does not need an oil change.
Have the level checked by a
PEUGEOT dealer in accordance
with the manufacturer's service
schedule.
Oil filter
Change the filter regularly, in accor
dance with the service schedule.
18-11-2002

141
TYRE UNDERINFLATION
DETECTION
Sensors check the tyre pressure
during driving, and trigger a warning
in the event of malfunction (speed
greater than 15mph [25 km/h]).
Flat tyre
When the message "Tyres deflat
ed" appears on the multi–function
display, accompanied by an audible
signal, have the tyre pressure
checked as soon as possible.
Puncture
The message 'Punctured tyre(s)'
appears on the multi–function dis
play, accompanied by an audible sig
nal and followed by illumination of
the "STOP" warning light.
Stop immediately, avoiding any sud
den movement of the steering wheel
and the brakes.
Change the damaged (punctured or
very deflated) tyre, and have the tyre
presure checked as soon as possi
ble.
Note: if the damaged tyre is tem
porarily stored in the boot, it will
again emit this message to remind
you of the necessity of having it
repaired. This will prevent another
warning of the same type being dis
played. Sensor(s) not detected
When the message
"X tyre pres
sure sensor(s) missing" appears
on the multi–function display,
accompanied by an audible signal,
this indicates that underinflation
detection is absent from one (or sev
eral) tyre(s).
Contact a PEUGEOT dealer to
replace the faulty sensor(s).
Note: this message is also displayed
when one of the tyres is away from
the vehicle (being repaired) or when
a wheel without a sensor is fitted.
PRACTICAL INFORMATION
All repairs and changing
of tyres on a wheel fitted
with this system must be
carried out by a
PEUGEOT dealer.
The tyre underinflation detec
tion system is a driving aid
which does not take the place
of vigilance or the responsibili
ty of the driver.
This system does not remove the
need to have the tyre pressure
checked regularly (including the
spare wheel), to ensure that the
dynamic performance of the vehi
cle remains at its best and to
avoid premature wear of the tyres,
in particular in the case of arduous
driving (heavy load, high speed).
The system may temporarily be
disturbed by radio broadcasts on
a frequency close to it.
18-11-2002

PRACTICAL INFORMATION
142
CHANGING A WHEEL
Parking the vehicle
 If possible, park the vehicle on
level, stable and nonslippery
ground.
 Apply the handbrake, switch off
the ignition and engage first or
reverse gear (position Pfor the
automatic gearbox) .
Access to the spare wheel  Open the tailgate.
 Pull and turn the towing eye to
unlock the lifting tool and access
the bolt.
 Unscrew the bolt fully, using the
wheelbrace 1to unwind the lifting
tool cable.
 Detach the spare wheel through
the rear of the vehicle.
 Take out the hinged hook via the
wheel shaft to release it. Tools
The following tools are located in the
engine compartment
1
Wheelbrace.
2 Jack
3 Removable towing eye.
4 Alloy wheel embellisher remover
Removing the wheel  Place a chock 3if possible under
the wheel diagonally opposite to
the one to be changed.
 Remove the trim, using the wheel
brace 1, pulling at the valve pas
sage hole. 
Loosen the wheel bolts (for vehi
cles fitted with alloy wheels,
remove the wheel embellisher 4).
 Remove the cover from the jack
suport holder.
 Detach the jack fixing strap and
take it out from the bottom of the
jack support holder.
 Place the jack 2in contact with
one of the four locating points A
on the subframe (the one which
is closest to the wheel to be
changed).
 Extend the jack 2until its base is
in contact with the ground. Ensure
that the centre line of the base of
the jack is straight above the
locating point A.
 Raise the vehicle.
 Unscrew the bolts and remove the
wheel.
18-11-2002

PRACTICAL INFORMATION143
Antitheft bolts*
If your wheels are fitted with an anti
theft bolt (one per wheel), unscrew
the bolt using one of the antitheft
sockets which were given to you on
delivery of your vehicle along with
the duplicate keys and confidential
card and the wheelbrace
1.
Note: make a careful note of the
code number on the head of the anti
theft socket. This willl enable you to
obtain a duplicate antitheft socket.
* According to specification and country. Fitting a wheel
 Position the wheel using the cen
tralising tool, fitted on the hub.
 Tighten the bolts by hand.
 Partly tighten the bolts using the
wheelbrace 1.
 Fold the jack 2completely and
remove it.
 Fully tighten the bolts using the
wheelbrace 1.
 Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it on
using the palm of the hand.
 Refit the wheel, with the valve
towards the top, under the vehicle
with the lifting tool, in line with the
illustration.
 Tighten fully and check that the
wheel is lying flat against the rear
floor. For your safety, always
change the wheel:
– on level, stable, nonslippery ground,
– with the handbrake on and the ignition switched off,
– with first or reverse gear engaged (position Pfor the
automatic gearbox),
– with the vehicle chocked.
Never go underneath a vehicle
that is supported only by a jack
(use a ramp).
After changing the wheel:
– have the tightening of the bolts and the tyre pressure checked
by a PEUGEOT dealer as soon
as possible.
– have the punctured wheel repaired and refit it to the vehi
cle as soon as possible.
– ask a Peugeot dealer to check that the spare wheel is fitted cor
rectly.
 Fold down the ring to lock the lift
ing tool.
 Put the tools in the engine com
partment.
18-11-2002

Direction indicator repeaters:
WY 5 W (amber). Push the repeater rearwards and
release it from the mirror.
 Hold the connector and turn the
bulb holder a quarter turn to the
left.
 Turn the bulb a quarter turn to
the left, remove it and change it.
When refitting, engage the
repeater towards the rear and
move it towards the front of the
mirror. Rear lights
1 Direction indicators:
PY 21 W
(amber) .
2 Brake/side lights: P 21/5 W.
3 Reversing lights: P 21 W.
4 Fog lamps: P 21 W.
These 4 bulbs are changed from
inside the vehicle:  open the tailgate,
 remove the air extraction grille on
the side concerned,
 unclip the light harness,
 unscrew the two interior nuts and
remove the light,
 unscrew the bulb holder concer
ned an eighth turn to the left and
remove it,
 unscrew the faulty bulb an eighth
turn to the left and change it. When refitting: 
take care to position the bulb cor
rectly and press on it to engage it,
 take care to position the bulb hol
der correctly and press on it to
engage it,
 take care to position and secure
the light correctly.
Number plate lights:
W 5 W  Remove the lens.
 Change the faulty bulb.
PRACTICAL INFORMATION 145
Third brake light:
5 W 5 W bulbs.  Remove the tailgate upper trim by
unclipping it on either side.
 Squeeze the two tabs 1to release
the bulb holder.
 Change the faulty bulb.
 When refitting, ensure that the
tailgate upper trim has been put
back in place correctly.
Note: when two or more bulbs are
faulty, you must replace them imme
diately.
Amber coloured bulbs
(direction indicators and
side repeaters), must be
changed for bulbs of iden
tical specification and
colour.
18-11-2002

Direction indicator repeaters:
WY 5 W (amber). Push the repeater rearwards and
release it from the mirror.
 Hold the connector and turn the
bulb holder a quarter turn to the
left.
 Turn the bulb a quarter turn to
the left, remove it and change it.
When refitting, engage the
repeater towards the rear and
move it towards the front of the
mirror. Rear lights
1 Direction indicators:
PY 21 W
(amber) .
2 Brake/side lights: P 21/5 W.
3 Reversing lights: P 21 W.
4 Fog lamps: P 21 W.
These 4 bulbs are changed from
inside the vehicle:  open the tailgate,
 remove the air extraction grille on
the side concerned,
 unclip the light harness,
 unscrew the two interior nuts and
remove the light,
 unscrew the bulb holder concer
ned an eighth turn to the left and
remove it,
 unscrew the faulty bulb an eighth
turn to the left and change it. When refitting: 
take care to position the bulb cor
rectly and press on it to engage it,
 take care to position the bulb hol
der correctly and press on it to
engage it,
 take care to position and secure
the light correctly.
Number plate lights:
W 5 W  Remove the lens.
 Change the faulty bulb.
PRACTICAL INFORMATION 145
Third brake light:
5 W 5 W bulbs.  Remove the tailgate upper trim by
unclipping it on either side.
 Squeeze the two tabs 1to release
the bulb holder.
 Change the faulty bulb.
 When refitting, ensure that the
tailgate upper trim has been put
back in place correctly.
Note: when two or more bulbs are
faulty, you must replace them imme
diately.
Amber coloured bulbs
(direction indicators and
side repeaters), must be
changed for bulbs of iden
tical specification and
colour.
18-11-2002

PRACTICAL INFORMATION
146
Fuse n
o
. Rating Functions
1 10 A Rear fog lamp.
2 15 A Rear screen wiper.
4 15 A Supply to functions via the builtin systems interface.
5 10 A Left brake light.
7 20 A Map readers Lighter Passenger lower glove box
lighting Electrochrome interior mirror .
Fascia panel fuses
 Unscrew the bolt a quarter of a
turn with a coin, then pull the
handle to open the cover and
access the fuses.CHANGING A FUSE
The fuse boxes are located under
the fascia (driver's side), in the batte
ry compartment (floor, driver's side)
and in the engine compartment.
The spare fuses and special pliers A
are fixed to the inside of the lid of the
instrument panel fuse box.
Removing and changing a
fuse
Before changing a fuse you must
establish the cause of the fault and
have it corrected. The fuse numbers
are indicated on the fuse box.
 Use the special pliers A.
Always change a faulty fuse for
one of the same rating.
Correct Incorrect
Pliers A
18-11-2002

PRACTICAL INFORMATION
146
Fuse n
o
. Rating Functions
1 10 A Rear fog lamp.
2 15 A Rear screen wiper.
4 15 A Supply to functions via the builtin systems interface.
5 10 A Left brake light.
7 20 A Map readers Lighter Passenger lower glove box
lighting Electrochrome interior mirror .
Fascia panel fuses
 Unscrew the bolt a quarter of a
turn with a coin, then pull the
handle to open the cover and
access the fuses.CHANGING A FUSE
The fuse boxes are located under
the fascia (driver's side), in the batte
ry compartment (floor, driver's side)
and in the engine compartment.
The spare fuses and special pliers A
are fixed to the inside of the lid of the
instrument panel fuse box.
Removing and changing a
fuse
Before changing a fuse you must
establish the cause of the fault and
have it corrected. The fuse numbers
are indicated on the fuse box.
 Use the special pliers A.
Always change a faulty fuse for
one of the same rating.
Correct Incorrect
Pliers A
18-11-2002

PRACTICAL INFORMATION147
Fuse n
o
. Rating Functions
9 30 A Front electric windows Front sunroof.
10 20 A Diagnostic socket Trailer socket.
11 15 A Alarm Telematics Audio equipment Multifunction displays Steeri ng wheel controls
Particle emission filter.
12 10 A Right side lights Number plate lighting
Air conditioning panel light Courtesy lights.
14 30 A Central locking Deadlocking.
15 30 A Rear windows.
16 5 A Air bags control unit supply via the builtin systems interface
17 15 A Right brake light, 3rd
brake light Trailer brake lights.
18 10 A Diagnostic socket supply – Brake and clutch pedal switches.
19 40 A PARC shunt.
20 10 A Audio equipment supply via the builtin systems interface.
22 10 A Left side lights Trailer side lights.
23 15 A Alarm siren Automatic gearbox control unit.
24 15 A Rear parking assistance supply via the builtin systems interface.
26 40 A Heated rear screen.
18-11-2002

TOWING A TRAILER,
CARAVAN, BOAT ETC...
Only use original PEUGEOT tow
bars which have been tested and
approved from the design stage of
your vehicle.
The tow bar must be fitted by a
PEUGEOT dealer.
Driving advice
Distribution of loads: distribute the
load in the trailer so that the heaviest
loads are as close as possible to the
axle and the nose weight is close to
the maximum authorised without,
however, exceeding it.
Cooling: towing a trailer on a slope
increases the coolant temperature.
As the fan is electronically con
trolled, its cooling capacity is not
dependent on the engine speed.
On the contrary, use a high gear to
lower the engine speed, and reduce
your speed.
In all cases, pay attention to the
coolant temperature. Note:
in certain cases of particularly
arduous use (towing the maximum
load up a steep slope in high tem
peratures), the engine automatically
limits its power. In this case, cutting
off the air conditioning allows the
engine power to be recovered, and
therefore the towing speed to be sig
nificantly increased (approximately
12mph [20 km/h] more).
If the coolant temperature warning
light comes on, stop the vehicle and
switch off the engine as soon as pos
sible.
Tyres: check the tyre pressures
of the towing vehicle and of the trail
er, observing the recommended
pressure.
Brakes: towing increases the brak
ing distance. Drive at a moderate
speed, change down early and brake
gradually.
Side wind: sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed. Lighting
Manual adjustment
Adjust your headlamps so as not to
dazzle other road users (see section
on ''Manual adjustment of head
lamps''). Check the electrical sig
nalling of the trailer.
Automatic beam correction
For vehicles with Xenon bulbs, this
system automatically corrects the
height of the beam, whatever the
load of the vehicle. The driver is then
assured of having optimum lighting
and not causing a nuisance to other
road users.
PRACTICAL INFORMATION
155
18-11-2002