lights PEUGEOT 807 2009.5. User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009.5., Model line: 807, Model: PEUGEOT 807 2009.5.Pages: 266, PDF Size: 12.92 MB
Page 34 of 266
Instruments and controls
READY TO SET OFF
2
37
Zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
- Switch off the ignition,
- Press and hold the trip recorder re-set b u t t o n ,
- Switch on the ignition.
T h e d i s p l a y b e g i n s a c o u n t d o w n .
When the display shows "= 0 ", release
t h e b u t t o n ; t h e s p a n n e r d i s a p p e a r s .
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information. Oil level correct
Lack of oil
Flashing of
"OIL" ,
linked with the
service warning light,
a c c o m p a n i e d b y a n
a u d i b l e s i g n a l a n d a m e s s a g e o n t h e
display, indicates a lack of oil which
could damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y a c h e c k
using the dipstick, it is essential that
the level is topped up.
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunction
of the engine oil level
gauge. Consult a
PEUGEOT dealer. Dipstick
A = maximum, never exceed
this level as a surplus of oil
may damage the engine.
Contact a PEUGEOT dealer
without delay.
B = minimum, top up the level
v i a t h e o i l fi l l e r c a p , u s i n g
the type of oil suited to your
engine.
Trip recorder zero
reset button
With the ignition on, press
t h e b u t t o n u n t i l t h e z e r o s
appear.
Lighting rheostat
With the lights on, press
t h e b u t t o n t o v a r y t h e
intensity of the lighting
of the instruments and
controls. When the lighting reaches
the minimum (or maximum) setting,
r e l e a s e t h e b u t t o n t h e n p r e s s i t a g a i n
t o i n c r e a s e ( o r r e d u c e ) t h e b r i g h t n e s s .
As soon as the lighting is of the
r e q u i r e d b r i g h t n e s s , r e l e a s e t h e b u t t o n .
T h e l e v e l r e a d w i l l o n l y b e c o r r e c t
if the vehicle is on level ground
a n d t h e e n g i n e h a s b e e n o f f f o r
more than 15 minutes.
After this operation, if you wish to
d i s c o n n e c t t h e b a t t e r y , l o c k t h e
v e h i c l e a n d w a i t f o r a t l e a s t fi v e
m i n u t e s , o t h e r w i s e t h e z e r o r e - s e t w i l l
n o t b e r e g i s t e r e d .
Page 41 of 266
Steering wheel controls
ERGONOMICS and COMFORT
3
45
Automatic lights
I f y o u r v e h i c l e i s fi t t e d
with a brightness
sensor.
Lights off
D i p p e d b e a m ( g r e e n )
M a i n b e a m ( b l u e )
DIRECTION INDICATORS
(green flashing)
STEERING WHEEL CONTROLS
C h e c k i n g b y m e a n s o f t h e i n d i c a t o r
lights on the instrument panel is
d e s c r i b e d i n t h e " I n s t r u m e n t s a n d
c o n t r o l s " s e c t i o n o f c h a p t e r 2 .
S i d e l i g h t s
LIGHTING CONTROL
Left : d o w n w a r d s .
Right : u p w a r d s . Front and rear lights
Selection is by turning ring
A .
Page 42 of 266
Steering wheel controls
ERGONOMICS and COMFORT
3
45
Automatic lights
I f y o u r v e h i c l e i s fi t t e d
with a brightness
sensor.
Lights off
D i p p e d b e a m ( g r e e n )
M a i n b e a m ( b l u e )
DIRECTION INDICATORS
(green flashing)
STEERING WHEEL CONTROLS
C h e c k i n g b y m e a n s o f t h e i n d i c a t o r
lights on the instrument panel is
d e s c r i b e d i n t h e " I n s t r u m e n t s a n d
c o n t r o l s " s e c t i o n o f c h a p t e r 2 .
S i d e l i g h t s
LIGHTING CONTROL
Left : d o w n w a r d s .
Right : u p w a r d s . Front and rear lights
Selection is by turning ring
A .
Page 43 of 266
Steering wheel controls
46
F r o n t f o g l i g h t s ( g r e e n )
a n d r e a r f o g l i g h t s
( a m b e r , 2 n d r o t a t i o n o f
t h e r i n g f o r w a r d s ) . T o s w i t c h o f f t h e f r o n t a n d r e a r
f o g l i g h t s , t u r n t h e r i n g r e a r w a r d s
twice in succession.
Front and rear fog lights
Rotate ring B f o r w a r d s t o s w i t c h o n
a n d r e a r w a r d s t o s w i t c h o f f . T h e
s t a t u s i s c o n fi r m e d b y t h e l i g h t o n t h e
instrument panel.
T h e s e o p e r a t e w i t h t h e s i d e l i g h t s a n d
t h e d i p p e d b e a m h e a d l a m p s . I n c l e a r w e a t h e r o r i n r a i n , b o t h
d a y a n d n i g h t , r e a r f o g l i g h t s
d a z z l e a n d a r e p r o h i b i t e d .
Do not forget to switch them off when
t h e y a r e n o l o n g e r n e e d e d .
Automatic switching on of the lights
s w i t c h e s o f f t h e r e a r f o g l a m p s , b u t t h e
front fog lamps remain on.
Daytime lights
D e p e n d i n g o n t h e c o u n t r y i n w h i c h
t h e v e h i c l e i s s o l d , t h e v e h i c l e m a y
b e e q u i p p e d w i t h d a y t i m e l i g h t s . T h e
d i p p e d h e a d l a m p s c o m e o n w h e n t h e
v e h i c l e i s s t a r t e d .
T h e i n s t r u m e n t s a n d c o n t r o l s
( i n s t r u m e n t p a n e l , d i s p l a y , a i r
c o n d i t i o n i n g c o n t r o l p a n e l , . . . ) a r e
only lit on switching to the automatic
s w i t c h i n g o n o f t h e l i g h t s m o d e o r
w h e n t h e l i g h t s a r e s w i t c h e d o n
manually.
Dipped beam/main beam change
P u l l t h e s t a l k f u l l y t o w a r d s y o u .
F r o n t f o g l i g h t s ( g r e e n ,
1st rotation of the ring
f o r w a r d s ) .
Lights-on buzzer
W h e n t h e i g n i t i o n i s s w i t c h e d o f f , w h e n
t h e d r i v e r ' s d o o r i s o p e n e d , a b u z z e r
s o u n d s i f y o u h a v e l e f t y o u r l i g h t s o n .
This warning light comes on
on the instrument panel.
Page 44 of 266
Steering wheel controls
ERGONOMICS and COMFORT
3
47
Automatic "Follow-Me-Home"
lighting
W i t h t h e i g n i t i o n o f f , w h e n y o u l e a v e
your vehicle with the automatic
switching on of the lights function
activated , t h e s i d e l i g h t s a n d d i p p e d
h e a d l a m p s r e m a i n o n f o r t h e s e l e c t e d
d u r a t i o n .
T o d e a c t i v a t e o r a c t i v a t e t h i s
f u n c t i o n , g o t o t h e d i s p l a y
c o n fi g u r a t i o n m e n u .
T h e d u r a t i o n o f t h e t i m e d p e r i o d m u s t
a l s o b e s e t ( 1 5 , 3 0 , 6 0 s e c o n d s ) , v i a
t h e d i s p l a y c o n fi g u r a t i o n m e n u .
Carry out these operations when the
vehicle is stationary.
HEADLAMPS BEAM
D e p e n d i n g o n t h e l o a d i n y o u r v e h i c l e ,
t h e b e a m s e t t i n g m u s t b e a d j u s t e d .
0 - 1 o r 2 p e o p l e i n t h e f r o n t s e a t s .
1 - 5 people.
2 - 6 to 8 people.
3 - D r i v e r + m a x i m u m a u t h o r i s e d
l o a d s .
Initial setting is position 0.
I n f o g g y w e a t h e r o r i n s n o w ,
the brightness sensor can
d e t e c t s u f fi c i e n t l i g h t . A s a
c o n s e q u e n c e , t h e l i g h t s w i l l n o t c o m e
on automatically.
Automatic switching on of the lights Deactivation
T u r n t h e r i n g f o r w a r d s o r r e a r w a r d s .
T h e d e a c t i v a t i o n o f t h i s f u n c t i o n i s
a c c o m p a n i e d b y a m e s s a g e o n t h e
d i s p l a y .
T h e f u n c t i o n i s d e a c t i v a t e d t e m p o r a r i l y
when you use the manual lights stalk.
If the brightness sensor does not
function correctly , t h e l i g h t s c o m e o n
a c c o m p a n i e d b y t h e s e r v i c e w a r n i n g
l i g h t , a n a u d i b l e s i g n a l a n d a m e s s a g e
o n t h e d i s p l a y .
C o n t a c t a P E U G E O T d e a l e r .
Do not cover the brightness
s e n s o r l o c a t e d i n t h e c e n t r e o f t h e
f a s c i a . I t i s u s e d f o r t h e a u t o m a t i c
s w i t c h i n g o n o f t h e l i g h t s a n d f o r t h e
automatic wipers.
Activation
Turn the ring to the AUTO position.
The activation of this function is
a c c o m p a n i e d b y a m e s s a g e o n t h e
d i s p l a y .
AUTOMATIC ADJUSTMENT OF
THE XENON HEADLAMPS
O n v e h i c l e s w h i c h a r e fi t t e d w i t h x e n o n
h e a d l a m p s , t h i s s y s t e m a u t o m a t i c a l l y
c o r r e c t s t h e h e i g h t o f t h e l i g h t b e a m ,
r e g a r d l e s s o f t h e l o a d i n t h e v e h i c l e .
T h e d r i v e r i s t h e n g u a r a n t e e d o p t i m u m
l i g h t i n g w i t h o u t d a z z l i n g o t h e r r o a d
users.
Cancelling:
- " fl a s h " t h e h e a d l a m p s ,
-
g e t o u t o f t h e v e h i c l e a n d l o c k i t .
I f y o u r v e h i c l e i s fi t t e d
with a brightness
s e n s o r , t h e s i d e l i g h t s
a n d d i p p e d b e a m
h e a d l a m p s s w i t c h o n
automatically if the
l i g h t i s p o o r , o r d u r i n g o p e r a t i o n o f t h e
w i n d s c r e e n w i p e r s . T h e y s w i t c h o f f
as soon as the light becomes bright
e n o u g h o r t h e w i n d s c r e e n w i p e r s s t o p .
This function is not compatible with the
d a y t i m e l i g h t s .
Page 81 of 266
84
Practical information Front courtesy light
Automatic switching on/off
The front courtesy light comes on
w h e n t h e k e y i s r e m o v e d f r o m t h e
i g n i t i o n , w h e n t h e v e h i c l e i s u n l o c k e d ,
w h e n o n e o f t h e f r o n t d o o r s i s o p e n e d
or for location of the vehicle using the
remote control.
I t s w i t c h e s o f f g r a d u a l l y a f t e r t h e
i g n i t i o n i s s w i t c h e d o n a n d w h e n t h e
v e h i c l e i s l o c k e d . P e r m a n e n t l y o n , i g n i t i o n o n .
Front: comes on when one
o f t h e f r o n t o r r e a r d o o r s i s
o p e n e d .
Permanently off. I n d i v i d u a l r e a d i n g l i g h t
Rear courtesy light rows 2 and 3
T h e s e a r e s w i t c h e d o n a n d o f f b y
means of a manual switch.
COURTESY LIGHTS
R o w s 2 a n d 3 : c o m e s o n
w h e n o n e o f t h e r e a r d o o r s i s
o p e n e d .
Rear courtesy light
Page 88 of 266
90
Driving safety
HANDBRAKE
HAZARD WARNING LIGHTS
Press the button, the direction
i n d i c a t o r s fl a s h .
They can operate with the ignition off.
Automatic lighting of hazard
warning lights
Equipment conditioned according
to country: when braking in an
emergency, depending on the
deceleration, the hazard warning lights
come on automatically. They switch
o f f a u t o m a t i c a l l y t h e fi r s t t i m e y o u
accelerate.
It is also possible to switch them off by
pressing the button.
DRIVING SAFETY
Applying
When parking, pull the handbrake to
immobilize your vehicle. When parking
on a slope, direct your wheels towards
the pavement and pull the handbrake.
Releasing
Pull on the handle and press the button
to release the handbrake. Pull the button located at the end of the
handbrake forwards.
The handbrake lever lowers.
You can now pivot the seat.
To return to normal operation, pull the
lever upwards until a click is heard.
If the handbrake is still on or has
not been released properly, this is
indicated by:
Disengaging
I f y o u r v e h i c l e i s fi t t e d w i t h a v e r s i o n
with a rotating front seat, apply the
handbrake. a warning light which comes
on on the instrument panel,
an audible signal,
a message on the display.
Page 97 of 266
100
Airbags Disarming
The passenger’s front air bag alone
can be disarmed:
-
With the
ignition
switched
off ,
insert the key into the passenger air
bag disarming switch,
-
turn it to the "OFF" position,
-
then remove the key keeping the
slot in this position.
Front air bags
The front air bags are incorporated in
the centre of the steering wheel for the
driver and in the fascia for the front
passenger.
Front air bag fault
Reactivation
In the
"OFF" position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is removed,
turn the air bag slot to the "ON"
position to re-activate the air bag
and thus ensure the safety of your
passenger in the event of an impact. To ensure the safety of your
child, it is essential to disarm the
passenger air bag when you install
a rear-facing child seat on the front
passenger seat. Otherwise, the child
would risk being killed or seriously
i n j u r e d i f t h e a i r b a g w e r e t o i n fl a t e .
The air bag warning light
on the instrument panel is
lit throughout the period of
disarming. If the two air bag warning lights
are lit continuously, do not install
a rear-facing child seat. Consult a
PEUGEOT dealer.
Activation
They are deployed simultaneously,
unless the passenger’s front air bag
has been disarmed, in the event of a
serious front impact applied to all or
part of the front impact zone
A in the
longitudinal centreline of the vehicle
on a horizontal plane directed from the
front towards the rear of the vehicle.
T h e f r o n t a i r b a g i n fl a t e s b e t w e e n
the front occupant of the vehicle and
the fascia to cushion his forward
movement. If this warning light comes on,
accompanied by an audible
signal and a message on the
display, consult a PEUGEOT
dealer to have the system
checked.
Page 121 of 266
119
Levels
CHECKS
6
These regular maintenance
operations will keep your vehicle
in good running order. Consult the
instructions at PEUGEOT dealerships
or in the servicing booklet enclosed in
the handbook pack. To maintain the reliability of engines
and emission control systems, the use
of additives in engine oil is prohibited.
Oil change
It is imperative that this is carried out at
t h e i n t e r v a l s s p e c i fi e d a n d t h e v i s c o s i t y
g r a d e o f t h e o i l s e l e c t e d m u s t f u l fi l t h e
requirements in accordance with the
manufacturer’s servicing schedule.
Consult the instructions at PEUGEOT
dealerships.
R e m o v e t h e d i p s t i c k b e f o r e fi l l i n g .
C h e c k t h e l e v e l a f t e r fi l l i n g ( n e v e r
exceed the max mark).
Screw the cap back onto the sump
before closing the bonnet.
LEVELS
I f y o u h a v e t o r e m o v e / r e fi t t h e
engine style cover, handle it with
c a r e t o a v o i d d a m a g i n g t h e fi x i n g
clips.
Dipstick
Warning lights
Oil level
Check the level regularly and top up
between changes. The maximum
consumption is 0.5 litre per 600 miles
(1 000 km).
Check the level with the vehicle level,
engine cold, using the dipstick.
Viscosity selection
In all cases, the oil selected must meet
the manufacturer’s requirements. Checking by means of the
warning lights on the instrument
panel is described in chapter 2,
"Instruments and controls" section.
Changing the brake fluid
T h e b r a k e fl u i d m u s t b e c h a n g e d a t
the intervals stated, according to the
manufacturer’s servicing schedule.
U s e fl u i d s r e c o m m e n d e d b y t h e
m a n u f a c t u r e r , w h i c h f u l fi l D O T 4
standards.
The level must be between the MIN
and MAX marks on the reservoir.
I f fl u i d h a s t o b e a d d e d f r e q u e n t l y ,
this indicates a failure which must be
checked by a PEUGEOT dealer as
soon as possible.
There are two marks
on the dipstick:
A = maximum
I f y o u fi l l p a s t t h i s
mark, contact a
PEUGEOT dealer.
B = minimum
Never allow the level
to fall below this
mark.
Page 124 of 266
122
Battery
ECONOMY MODE FUNCTION
After the engine has stopped, with
the key in the ignition position, certain
functions (windscreen wiper, electric
windows, courtesy lights, audio
equipment, etc.) can only be used for
a cumulative duration of thirty minutes,
to prevent discharging the battery.
Once the thirty minutes are over, the
message "Economy mode active"
appears on the display and the active
functions are put on standby.
To resume the use of these functions
immediately, start the engine and let it
run for a few seconds.
A fl a t b a t t e r y w i l l p r e v e n t t h e e n g i n e
from starting.
To charge the battery using a
battery charger
- disconnect the battery,
- follow the instructions for use given by the battery charger
manufacturer,
- reconnect starting with the negative (-) terminal,
- check that the terminals and connectors are clean. If they are
covered with sulphate (white or
greenish deposit), disconnect them
and clean them.
BATTERY
This is housed in a compartment
l o c a t e d u n d e r n e a t h t h e fl o o r , i n f r o n t o f
the driver’s seat.
Before disconnecting the battery, you
must wait for 2 minutes after switching
off the ignition.
Never disconnect a terminal when the
engine is running.
N e v e r c h a r g e a b a t t e r y w i t h o u t fi r s t
disconnecting the terminals.
Close the sunroof and the windows
before disconnecting the battery. If
they do not operate normally following
reconnection of the battery, they must
be reinitialised.
It is advisable to disconnect the
battery if the vehicle is not to be used
for a period of more one month.
After every reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to allow the electronic
systems to be initialised. If slight
d i f fi c u l t i e s a r e e x p e r i e n c e d a f t e r t h i s ,
please contact a PEUGEOT dealer.
The door open monitoring electrical
system consumes power, remember
to close the sliding doors when your
vehicle is parked for long periods.
To start the vehicle from
another battery
- connect the red cable to the positive (+) terminals of the two
batteries,
- connect one end of the green or black cable to the negative (-)
terminal of the slave battery,
- connect the other end of the green or black cable to an earth point on
the broken down vehicle as far as
possible from the battery,
- operate the starter, let the engine run,
- wait for the engine to return to idle, then disconnect the cables. For the sunroofs safety auto-
reverse, refer to the "Accesses"
section of chapter 2. For the electric windows safety
auto-reverse, refer to the "Mirrors
and windows" section of chapter 3.