length Peugeot Boxer 2016 Owner's Manual - RHD (UK, Australia)

81
LoAd SPAcE FIttInGSSupport for stowing rail
Supports for securing a stowing rail are
available above the trims, on each side of
the vehicle.
Maximum load: 200 kg.
12 volt socket
Maximum power: 180 W.Lashing rings
Lashing rings are provided on the floor to
secure and make safe your loads: 8 for
L1 and L2 length vehicles, 10 for L3 and
L4
length vehicles.
two additional rings are located on the
partition behind the cab.
Maximum load: 500 kg.Side trim
the lower parts of the sides are fitted with
load protection trims.
As a safety precaution in case of sharp
braking, you are advised to place

heavy objects as far forwards towards the
cab as possible.
3
EASE oF uSE and coMFort
Practical information

107
rEAr SEAt BELtS
the rear seats/bench seats are fitted with
three-point seat belts and inertia reels.
the centre seat has a seat belt guide and


inertia reel, solid with the seat back.
A carrier is provided at each outer seat to
allow the seat belt buckle to be secured
when not in use.
Good practice
the driver must ensure that passengers use
the seat belts correctly and that they are all
strapped in securely before moving of
f.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
the seat belts are fitted with an inertia reel


which automatically adjusts the length of the
strap to your size.
Do not use accessories (clothes pegs, clips,
safety pins, etc.) which allow the seat belt
straps to fit loosely.
You can unfasten the seat belt by pressing
the red button on the buckle.
guide the seat


belt after unfastening.
ensure that the seat belt has reeled in


correctly after use.
After folding or moving a seat or a rear
bench seat, ensure that the seat belt has
reeled in correctly and that the buckle is
ready to accommodate the tongue.
the airbag warning lamp also


comes on if the pretensioners are
deployed. Contact a P
eugeOt
dealer or a qualified workshop.
In the event of an impact
Only for the front seats, and depending on
the nature and seriousness of the impact,


the pretensioning device may be deployed
before and independently of inflation of the
airbags. It instantly tightens the seat belts
against the body of the occupants.
Deployment of the pretensioners is
accompanied by a slight discharge of
harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
the force limiter reduces the pressure of the


seat belt against the body of the occupants.
the pyrotechnic pretensioners are active


when the ignition is switched on and the
seat belt fastened.
the inertia reels are fitted with a device


which automatically locks the strap in the
event of a collision or emergency braking or
if the vehicle rolls over.
5
SAFetY
Seat belts

123
rooF cArrYInG SYStEMS
Refer to the "technical data -
Dimensions" section for more
information on the length (L1 to L4) and the
height (H1 to H3) of the vehicle. Maximum load on the roof, evenly
distributed: 150 kg, for all versions,
within the vehicle's weight limit (
gross

Vehicle Weight).
For reasons of safety and to avoid damaging
the roof, it is essential to use a carrying
system (roof bars or roof rack) that is
approved for your vehicle.
Roof bars can only be fitted to an H1 or H2
height van, combi and minibus versions. On
a minibus, check for the presence of roof air
conditioning units.
the carrying system must always be

secured to the fitting points provided on the
vehicle's roof: 6, 8 or 10, depending on the
wheelbase of the vehicle.
Observe the instructions for fitting and use
provided with the carrying system.
On all H3 height versions, the roof
cannot be fitted with a carrying system.
Observe in full the legal requirements
related to carrying outsized loads.
6
transport solutions
ACCeSSORIeS

173
dIMEnSIonS
the dimensions are given in millimetres.
this model is available in 4 lengths (L1...) and 3 heights (H1...); r\
efer to the corresponding tables:VA
n
L1L2L3L4
H1 H2 H1 H2 H2 H3 H2 H3
L Overall length 4
9635 4135 9986 363
H Overall height 2
254

2 524 2
254
2 524 2
524
2
764
2
524
2
764
A Wheelbase 3
0003 450 4 035
B Front overhang 948
cRear overhang1 0151 380
dOverall width (incl./excl. mirrors) 2 508 / 2 050
E Width of front track 1
810
F Width of rear track 1
790
G Height of load floor 535 to 565
I Length of interior floor 2
6703 1203 7054 070
jMaximum interior load height 1 662

1
932
1
662
1
932
1
932
2
172
1
932
2
172
K Maximum interior width 1
870
M Interior width between wheel arches 1
422
V

olume (m
3) 89.5 10 11.5 13 15 15 17
9
teCHNICAL DAtA
Dimensions

252
dIMEnSIonS
the dimensions are given in millimetres.
cHASSIS cAB
FL
oor cAB
L1 L2L2S L3L4
L Overall length 4
9085 3585 7085 9436 208
A Wheelbase 3
0003 4503 8004 0354 035
B Front overhang 948
cRear overhang9601 225
dOverall width (incl./excl. mirrors) 2 508 / 2 050
- Passable width 2
207
- Max permitted body width 2
350
E Front track 1
810
- Rear track 1
790
- Width of increased rear track 1
980
F Overall height 2
153
- Max permitted body height 3
500
Chassis cab / Floor cab

256
dIMEnSIonS
the dimensions are given in millimetres.
cHASSIS douBLE cAB
FL
oor douBLE cAB
L2 L3L4
L Overall length 5 7986 2286 678
A Wheelbase 3 4504 0354 035
B Front overhang 948948948
cRear overhang 1 2451 3401 695
dWidth (with / without mirrors) 2 508 / 2 1002 508 / 2 1002 508 / 2 100
E Front track 1 8101 8101 810
- Rear track 1 7901 7901 790
F Overall height 2 4242 4242 424
Double cab

261
tipper (in mm)
Load length 3 200
Overall length 3
248
Load width 2 000
Overall width 2 100
Height of body sides 350
Overall height 550
dIMEnSIonS
this conversion is only available on the L2 single chassis-cab; refer to \
the table below for the characteristics of the tipper.
For information on the characteristics of the L2 chassis cab, refer to t\
he "Dimensions" section for the floor cab version.
SPeCIAL FeAtuReS
tipper body