steering Peugeot Boxer 2016 Owner's Guide

52
boxer_en_Chap03_ergo-et-confort_ed01-2015
cruISE controL
"this is the speed at which the driver wishes
to drive".
t

his aid to driving in free-flowing traffic
enables the vehicle to maintain the speed
programmed by the driver, unless a
steep gradient or heavy load makes this
impossible. In order for it to be programmed or
activated, the vehicle speed must be greater
than 18 mph (30 km/h) with 2
nd gear or
higher engaged. Function selected.
Function deactivated.
Selecting the function
- turn the ring fully upwards. t
he cruise
control is selected but is not yet active
and no speed has been programmed.
t

he indicator comes on in the instrument
panel
t
he status of the cruise control is given
by an indicator in the rev counter and
messages in the instrument panel screen.
Steering mounted controls

53
boxer_en_Chap03_ergo-et-confort_ed01-2015
First activation /
programming a
speed
- Reach the chosen speed by pressing
the accelerator.
-

Move the switch up (+) or down (-)

to memorise the speed. A message
appears in the instrument panel screen
to confirm the operation.
t

he vehicle will maintain this speed setting.
temporarily exceeding the speed
setting
It is possible to accelerate and drive
momentarily at a speed greater than the
programmed speed.
When the accelerator pedal is released, the
vehicle will return to the programmed speed.
reactivation
- Following deactivation of the cruise
control, press this button. A message
appears in the instrument panel screen
to confirm the reactivation.
Your vehicle will return to the last
programmed speed.
Alternatively, you can repeat the "first
activation" procedure.
deactivation (off)
- Press this button or the brake or clutch
pedal. A message appears in the
instrument panel screen to confirm the
deactivation.
3
EASE oF uSE and coMFort
Steering mounted controls

54
boxer_en_Chap03_ergo-et-confort_ed01-2015
there are two methods of memorising a
speed higher than the previous one:
Without using the accelerator:
-

Move the switch up (+).
A

brief press increases the speed by
1 mph (km/h).
A maintained press increases the speed in
steps of 5 mph (km/h).
u

sing the accelerator:
-

exceed the memorised speed until the

speed required is reached,
-

move the switch up (+) or down (-).
to memorise a speed lower than the


previous one:
-

move the switch down (-).
A

brief press decreases the speed by
1 mph (km/h).
A maintained press decreases the speed in
steps of 5 mph (km/h).
changing the
programmed
speed Switching the system off
- Place the ring in the central
o position
or switch off the ignition to switch the
system off.
When the vehicle becomes stationary, after
switching off the ignition, the system no
longer memorises a speed.
operating fault
In the event of a fault, the system
switches off and the indicator
goes off. Contact a P
euge O t

dealer or a qualified workshop to


have the system checked.
Good practice
When changing the programmed reference
speed by means of a maintained press,
pay attention as the speed can increase or
decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
In the event of a steep slope, the cruise
control cannot prevent the vehicle from
exceeding the programmed speed.
In any event, the cruise control cannot
replace the need to observe the speed
limits, nor can it replace the need for
vigilance on the part of the driver.
It is advisable to leave your feet near the
pedals.
to avoid any jamming under the pedals:
-


ensure that the mat and its fixings on the

floor are positioned correctly,
-

never place one mat on top of another
.
Steering mounted controls

55
boxer_en_Chap03_ergo-et-confort_ed01-2015
SPEEd LIMItEr
"this is the selected speed which the driver
does not wish to exceed".
t

his selection is made with the vehicle
stationary and the engine running or with the
vehicle moving and 2
nd gear or higher engaged.
t

he lowest speed that can be programmed
is 20 mph (30 km/h).
t

he speed of the vehicle responds to the
pressure of the driver's foot as far as the
accelerator pedal point of resistance which
indicates that the programmed speed has been
reached. However, pressing the pedal beyond this
point of resistance to the floor permits
exceeding of the programmed speed.
to


resume use of the limiter, simply reduce
the pressure on the accelerator pedal
gradually and return to a speed below that
programmed.
t

he operating actions may be carried out
with the vehicle stationary and the engine
running, or with the vehicle moving.
t
his speed limiter shows the status of the
system and the programmed speed in the
instrument panel screen:
System selected,
display of the "Speed
Limiter" indicator.
System deactivated,
last programmed speed - o FF
(example at 65 mph
(107 km/h)).
System activated
(example at 65 mph (107 km/h)).
Vehicle speed above
(example 70 mph (118 km/h))
the programmed speed is
displayed flashing.
Operating fault detected,
o

FF - the dashes flash.
3
EASE oF uSE and coMFort
Steering mounted controls

56
boxer_en_Chap03_ergo-et-confort_ed01-2015
Selecting the function
- turn the ring fully downwards. the
speed limiter is selected but is not yet
active.
t

he display indicates o FF and
the last programmed speed.
Programming a speed
A speed can be programmed without
activating the limiter but with the engine
running.
to memorise a speed higher than the


previous one:
-

move the switch up (+).
A

brief press increases the speed by
1
mph (km/h).
A maintained press increases the speed in
steps of 5 mph (km/h).
to memorise a speed lower than the


previous one:
-

move the switch down (-).
A

brief press decreases the speed by
1 mph (km/h).
A maintained press decreases the speed in
steps of 5 mph (km/h).
Activation/deactivation
Pressing this button once activates the
speed limiter, o FF disappears from the
screen and a message appears to confirm
the activation.
A second press deactivates it,
o FF
reappears in the screen and a message
appears to confirm the deactivation.
Steering mounted controls

57
boxer_en_Chap03_ergo-et-confort_ed01-2015
Exceeding the programmed
speed
Pressing the accelerator pedal in order to
exceed the programmed speed will have
no effect unless you press the pedal firmly
beyond the point of resistance.
If the limiter is unable to prevent an increase
in the speed of the vehicle because of the
profile of the road or when going down a
step hill, the programmed speed may be
exceeded.
t

he limiter is deactivated temporarily and
the programmed speed flashes.
to return to the limiter function, reduce your


speed to below the programmed speed.
Switching the system off
- Place the ring in the central o position
or switch off the ignition to switch the
system off.
t

he last programmed speed remains in the
memory.
operating fault
the programmed speed is cleared then
replaced by dashes.
Contact a P
euge O t
dealer or a qualified

workshop to have the system checked.
Good practice
In any event, the speed limiter cannot
replace the need to observe speed limits,
nor can it replace the need for vigilance on
the part of the driver.
Always pay attention to the profile of the
road and sharp acceleration and stay in
complete control of your vehicle.
to avoid any jamming under the pedals:
-


ensure that the mat and its fixings on the

floor are positioned correctly,
-

never place one mat on top of another
.
3
EASE oF uSE and coMFort
Steering mounted controls

58
boxer_en_Chap03_ergo-et-confort_ed01-2015
FIxEd SPEEd LIMItEr
If your vehicle is fitted with this function, the
speed of your vehicle can be limited to a
fixed speed of approximately 55 mph
(90 km/h) or 60 mph (100 km/h).
A label in the passenger compartment
indicates this maximum speed.
t

he fixed speed limiter is not a function
of the cruise control type. It cannot be
activated or deactivated by the driver while
driving.
t

he maximum speed set in the factory
depends on the legislation in force in
the country of sale.
t

his maximum speed cannot be modified by
the driver.
If you want the maximum speed modified, go
to a P
euge O t
dealer
.
Steering mounted controls

64
boxer_en_Chap03_ergo-et-confort_ed01-2015
comfort value adjustment ring
the settings range between:
-
increasing the interior ambient air

temperature HI (High) which goes up to
to a maximum setting of 32,
-

cooling the interior ambient air

temperature LO (Low) which goes down
to a setting of 16.
Air distribution
A press illuminates the LeD on the buttons
which distribute the air flow towards:
the windscreen and front side

window vents (demisting/
defrosting the windows),
the central and side vents (chest
and face),
the vents in the front and rear
areas (feet).
t

he combination of buttons permits
improvement of air distribution.
Air flow
Successive presses of this button
increase (+) or reduce (-) the
force of the air flow to the interior.
Intake of exterior air / r ecirculation of interior air
When the LeD is on, the air
recirculates inside the passenger
compartment to prevent the entry of exterior
odours and smoke.
t

his position should be
temporary.
When the ambient air comfort level has been
reached, pressing the button switches the
L
e
D off and reopens the exterior air intake.
Pressing the A
uto button also restores
the intake of exterior air. Returning to this
position permits renewal of the air in the
passenger compartment and demisting.
Pressing the A
uto button again restores
the F
u
LL A uto function.
rapid demisting / defrosting
Pressing this control permits
rapid clearing of the windows.
t

he L
e
D is on.
t

he system manages the air conditioning,
the flow and intake of air, the defrosting
of the rear screen and provides optimum
distribution of the air to the windscreen and
front side windows.
If your vehicle is fitted with additional
heating, switch it off to ensure rapid and
effective demisting/defrosting.
AddItIonAL r EA r VE nt ILAt I on
the controls for this system, additional to
the standard cabin ventilation system, are
on the lower dashboard, to the left of the
steering wheel.
Air outlet
A press on this control activates
the extraction of air to the
outside; the L
e D comes on.
Press again to switch off.
Air inlet
A press on this control activates
the entry of air into the cabin; the
L
e D comes on. Press again to
switch off.
Ventilation

67
boxer_en_Chap03_ergo-et-confort_ed01-2015
Setting the time of the internal clock
Set the clock on the control panel before
programming the deferred switching on of
the heating.Press and hold the "set" button.
t

he time setting screen and
indicator come on.
Within ten seconds, press one of the two
setting buttons until the correct time is
displayed: -

">"
to increase the time,
or
-

"<"
reduce the time.
reading the time
Pro
G
r
AMMABLE

A
dd
I
t
I
on
AL
HEAt

I
n
G
If your vehicle is fitted with separate
programmable heating, it gradually brings
the engine up to a good temperature to
facilitate starting.
An integrated clock permits programming of
its start time.
t

he passenger compartment
will be heated more quickly.
time display
digital programming control
the programmable heating control panel
is located to the side of the steering wheel
below the M
od E switch panel. Heating cycle indicator
time setting and reading indicator
Display of the programme number

selected
Ventilation indicator
time setting buttons
Programme selection button
Button for immediate switching on

of the heating Press and hold the button for more rapid
scrolling of the digits.
Release the"set" button.
When the screen is off, the time is
memorised.
Press the "<" or ">" button.
t
his time reading indicator comes
on and the time is displayed for
approximately ten seconds.
Ventilation
3
EASE oF uSE and coMFort

87
boxer_en_Chap04_technologie-a-bord_ed01-2015
PErSonALISAtI on - c on FIG ur At I on
u

sing the M od E control panel
this control panel located alongside the
steering wheel provides access to menus for
the personalisation of some of the vehicle
systems.
t

he corresponding information appears in
the instrument panel screen.
e

leven languages are offered: Brazilian,
Dutch,
e nglish, French, g erman, Italian,
Polish, Portuguese, Russian, Spanish and
turkish. Y

ou have access to all the menus if your
vehicle is fitted with an audio system.
If your vehicle is fitted with a touch screen
audio system, certain menus are only
accessible using the audio system control
panel.
-
scroll down through a menu,
-


decrease a value.
t
his M od E button enables you to:
-
access the menus and sub-menus,
-

confirm your selections, within

a menu,
-
exit from the menus.
A
long press enables you to return to
the welcome screen.
t
his button enables you to:
t

his button enables you to:
-

scroll up through a menu,
-


increase a value.
As a safety precaution, some menus
can only be accessed when the ignition
is off.
Vehicle configuration
4
teCHNOLOgY ON BOARD