lights PEUGEOT BOXER DAG 2003 User Guide

YOUR BOXER IN DETAIL107
Programming the remote control  Switch off the ignition.
 Switch the ignition on again.
 Immediately press button A.
 Switch off the ignition and remove the remote control key
from the ignition lock. The remotecontrol is now working again.
Confidential card The confidential card is necessary for any work carried out by a
PEUGEOT dealer on the system. It contains:
Ð a five digit identification code
1necessary for the emergency
starting procedure,
Ð a code 2for reproduction of your
keys by a PEUGEOT dealer.
These codes are hidden by a film, which should be removed only if
necessary. Keep your card in a safe place, never inside the vehicle. Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition. Changing the battery of the remote control If the indicator light on the key lights only once, or does not light at allwhen the button is pressed, change
the battery.
To do this, unclip the casing using a
coin at the ring (CR 2032/3 volt battery). If the remote control does not work after the battery has been changed,reinitialise the remote control.
ELECTRONIC ENGINE IMMOBILISER This locks the engine control system as soon as the ignition has been
switched off and therefore preventsstarting of the vehicle by anyone
who does not have the key. The ignition key has an electronic chip which has a special code.When the ignition is switched on, thecode must be recognised for startingto be possible. If the system does not function
correctly,
the electronic immobiliser
key indicator light, situated on theinstrument panel, flashes rapidlywhen the ignition is switched on(2nd notch). In this case your vehicle will not start.
Contact a PEUGEOT dealer as soon as possible. If the electronic immobiliser key indi- cator light comes on continuously
after switching on the ignition (2ndnotch), check the identification of
your key. It may also indicate an
operating anomaly.
Contact a PEUGEOT dealer as soon as possible.
17-11-2003

17-11-2003
YOUR BOXER IN DETAIL109
THE ALARM This provides two types of protection:
Ð exterior protection: it sounds if a
door, the tailgate or the bonnet is opened.
Ð interior protection: it sounds if the volume inside the passenger com-partment changes (breaking of awindow or a movement inside thevehicle).
Setting the alarm  Switch off the ignition and get out of the vehicle.
 Set the alarm within five minutesof getting out of the vehicle, bylocking using the remote control(the red indicator light, located onthe fascia, visible from outside,flashes once per second).
Note: if you wish to lock your vehicle
without setting the alarm, use thedoor lock. When the alarm is triggered, thesiren sounds and the direction indi-cator lights flash for thirty seconds. After triggering, the alarm remains set.
Warning:
if the alarm has been trig-
gered ten times in succession, on the eleventh time it becomes inactive. Note: if the red warning light, located
on the fascia, flashes rapidly, the alarm has been triggered while you
were away from your vehicle. To stopit flashing, insert the remote controlkey and switch on the ignition. Disarming Unlock the vehicle with the remote control key (the red indicator light,located on the fascia, goes out).
To set the alarm with exterior protection only If, while you are away from the vehi- cle, you wish to leave a window par-
tially open or a pet inside the vehicle,you should choose exterior protec-
tion only.  Switch off the ignition placing the key in the STOPposition.
 Place the key in the ONposition.
 Switch off the ignition placing thekey in the STOPposition.
 Remove the key.
The interior protection is disarmedwhen the red indicator light located onthe fascia comes on for two seconds. 
Get out of the vehicle.
 Within the next five minutes, setthe alarm by locking using theremote control (the red indicatorlight, located on the fascia, flash-es once a second).
Note: when the alarm is set but the
remote control does not operate:  Unlock the doors with the key
and open the door. The alarm istriggered.
 Switch on the ignition in the next
ten seconds. The alarm is dis-armed.
Incorrect operation When the ignition is switched on, if the red indicator light, located on thefascia, comes on for ten seconds,there is a fault in the siren connection.
Contact a PEUGEOT dealer to have the system checked. Do not make any modifications to the alarm system, this could cause faults.

17-11-2003
YOUR BOXER IN DETAIL113
THE LIGHTS STALK Front and rear lights Selection is by turning the ring.
Lights off Side lights Dipped headlamps
Main beam headlamps Dipped/Main beam change Push the stalk forwards to switch on the main beam headlamps. Pull the stalk towards you to switch
them off. Note:
with the ignition off, when the
driver's door is opened, a buzzer sounds if you have left your lights on. Front fog lamps Press the button in the centre of the
fascia panel. The warning light onthe button comes on. The front fog lamps operate with the dipped and main beam headlamps. Direction indicators (flashers)
Left: downwards.
Right: upwards.
Rear fog lamps Press the button in the centre of the
instrument panel. The warning lighton the button comes on. The rear fog lamps operate with the dipped and main beam headlamps.
In good or rainy weather, both day and night, therear fog lamps are daz-zling and are prohibited. Do not forget to switch the
fog lamps off when they are no longer needed.

17-11-2003
YOUR BOXER IN DETAIL
114
WINDSCREEN WIPER STALK
Windscreen wipers 4
Single wipe.
0 Park.
1 Intermittent wipe.
2 Normal wipe.
3 Fast wipe.
Windscreen and headlamp wash Pull the windscreen wiper stalk
towards you. The windscreen washthen the windscreen wipers operatefor a fixed period. The windscreen wash and headlamp wash operate simultaneously for twoseconds, only if the headlamps are
on .
Parking lights This system enables you to leave the side lights on when parked, with the
ignition off and the key removed. Press the safety control Aand turn the
key one notch in the opposite direction to starting at the same time.

17-11-2003
YOUR BOXER IN DETAIL
114
WINDSCREEN WIPER STALK
Windscreen wipers 4
Single wipe.
0 Park.
1 Intermittent wipe.
2 Normal wipe.
3 Fast wipe.
Windscreen and headlamp wash Pull the windscreen wiper stalk
towards you. The windscreen washthen the windscreen wipers operatefor a fixed period. The windscreen wash and headlamp wash operate simultaneously for twoseconds, only if the headlamps are
on .
Parking lights This system enables you to leave the side lights on when parked, with the
ignition off and the key removed. Press the safety control Aand turn the
key one notch in the opposite direction to starting at the same time.

17-11-2003
YOUR BOXER IN DETAIL117
ADJUSTING THE HEADLAMPS Depending on the load in your vehicle, adjusting the beam of the headlampsis recommended. 0 -
No load.
1 - Partial load.
2 - Average load.
3 - Maximum authorised load.
Initial setting is position 0. HAZARD WARNING LIGHTS Press the button, the direction indicators flash. They can operate with the ignition
off.
STEERING WHEEL HEIGHT ADJUSTMENT
When the vehicle is stationary, unlock the steering wheel by pullinghandle
Atowards you.
Adjust the height of the steeringwheel, then lock it by pushing handleA down fully.
HORN Press one of the spokes or the cen- tre of the steering wheel.

17-11-2003
YOUR BOXER IN DETAIL
118
COURTESY LIGHTS
1 - Front courtesy light.
You can select three positions:
Ð OFF:permanently off.
Ð AUTO (central posi-
tion) :lighting on
opening one of the doors.
Ð PERMANENT: permanent
lighting, when the key is inthe accessories positionor the ignition is on. 2 - Map reading lights
When the key is in the acces-sories position or the ignition ison, operate the correspondingswitch. 3 - Rear courtesy lights
Press the ends of the transparentcover to switch the courtesy light
on or off.

17-11-2003
PRACTICAL INFORMATION
138
CHANGING A BULB Front lights Removing a headlamp unit:
Ð Open the bonnet,
Ð Unscrew the bolts
Afrom the grille
to gain access to the unit 1,
Ð Unscrew the nuts Busing a wrench
and pull the unit 1outwards,
Ð Unclip the two strips C,
Ð Unclip the rubber protector D,
Ð Disconnect the connector. Note: handle the bulbs with a dry
cloth. 1 - Dipped beam headlamps
(H7-60 W),
 Press and release the spring G,
 Extract the bulb holder Hto
change the bulb.
2 - Main beam headlamps (H1-60 W),
 Press and release the spring E,
 Extract the bulb holder Fto
change the bulb.
3 - Front fog lamps (H1-60 W).  Contact a PEUGEOT dealer.When fitting the new bulb, ensure that the direction notches are posi-tioned correctly and the securing clip
is fixed properly. Carry out the operations in the reverse order to refit. The headlamp units are fitted with polycarbonate glass with a protec-tive coating. Do not clean them
with a dry or abrasive cloth, norwith a detergent or solvent prod-uct. Use a sponge and soapy water.

17-11-2003
Direction indicator side repeaters (W 5 W). Push the repeater rearwards and
release the assembly,
 Pull the bulb holder to gain accessto the bulb,
 Change the bulb.
PRACTICAL INFORMATION 139
4 - Direction indicators (P 21 W) and side lights (R 5 W). 
Remove the protective casing Bby pressing the two springs A.
 Turn the bulb holder Da quarter turn and remove it.
 Change the bulb (P 21 W).
 Pull the bulb holder C, remove the bulb (R 5 W) and change it,
 Carry out the operations in the reverse order to refit.
Note: in certain climatic conditions (low temperature, humidity), condensation
inside the headlamp glass is normal; it disappears a few minutes after the
lights are switched on.

17-11-2003
Rear lights
1 - Brake lights (P 21 W).
2 - Reversing lights (P 21 W).
3 - Direction indicators (PY 21 W).
4 - Fog lamps/Side lights (P 21/4 W). 
Unscrew the two bolts Aand
release the unit,
 Disconnect the connector B,
 Unscrew the two bolts Cat the
rear of the unit,
 Change the faulty bulb.
PRACTICAL INFORMATION
140
Number plate lights (C 5 W) Insert a thin screwdriver into one of the external holes of the lens.
 Push it outwards to unclip it.
 Remove the lens.
 Unscrew the bolt and release theassembly towards the right to
extract the bulb holder.
 Change the faulty bulb.
Chassis cab lights (W 5 W) Unscrew the four bolts to gain access to the bulbs.
Third brake light (W 5 W) 
Unscrew the 2 fixing screws.
 Release the lamp unit by push- ing it outwards.
 Disconnect the connector.
 Squeeze the two tabs to release
the bulb holder.
 Change the faulty bulb.
 When refitting, ensure that thelamp unit seal has been put back
in place correctly.