display Peugeot Expert Dag 2001.5 Owner's Manual

STEERING WHEEL ADJUSTMENTI-817
IMPORTANT
As a safety measure,
these manoeuvres must not be carried out when driving.
The height of the steering wheel can be adjusted.
When stationary, first adjust your seat to the most suitable position.
Unlock the steering wheel by pushing the adjustment control.Adjust the height of the steering wheel then lock it by pulling the adjustment control fully towards you. Make sure that you can see all the displays on the fascia panel.

INSTRUMENT PANEL*I-12
24
Display
¥ Digital clock.
¥ Maintenance indicator.
¥ Engine oil level indicator.
¥ Total mileage recorder.
¥ Trip mileage recorder.
Coolant temperature gauge Fuel gauge
Dashboard lighting rheostat See Page 31 Changing the time See Page 30
Display control:
¥ Total mileage recorder.
¥ Trip mileage recorder.
¥ Resetting the trip mileage recorder to zero. Tachometer Do not enter the red zone
* According to model or country

INSTRUMENT PANEL*I-12
26
Multifunction Display On switching the ignition on, the display shows in turn:
- Maintenance indicator.
- Engine oil level indicator.
- Total mileage recorder. Engine oil level indicator When the ignition is switched on, the maintenance indicator is displayed for several seconds followed by the engine oil level for approximately 10 seconds.
Max Min Check using the oil dipstick.
Check with the vehicle on level ground, and the engine off for at least 10 minutes.
Shortage of oil = Warning lamps flashing It is essential to top up the level. Risk of damage to the engine. Flashing can indicate either a malfunction of the gauge or a shortage of oil
Contact your dealer.
* According to model or country

INSTRUMENT PANEL*27I-12
Total mileage recorder & Trip mileage recorder Press button Ato alternate the display between the total mileage recorder and
the trip mileage recorder. Resetting the trip mileage recor- der to zero Press and hold down button
A, the
display will flash three times and read 0.
* According to model or country
AAA

INSTRUMENT PANEL*I-12
28
Maintenance indicator The maintenance indicator displays the number of miles to be covered before the next service (in accordance with the servicing schedules which appear in the Maintenance Guide). Operation: On switching on the ignition, the maintenance indicator spannerappears in the display for severalseconds ; the mileage recorder dis-play indicates how many milesremain to be travelled before thenext service is due. For example: you have the follo-
wing distance left to travel before the next service: Five seconds after switching on the ignition, the total mileage recorderreverts to normal operation and thetotal or trip mileages appear on the
display. Distance to be covered beforethe next service is less than
1000 miles. For example:
you have the follo-
wing distance left to travel before the next service : 900 Miles.For five seconds on switching onthe ignition, the display shows: Five seconds after switching on the ignition, the total mileage recorderreverts to normal operation and themaintenance spanner remains illu-minated. This signifies that the vehicle will be
due for a service shortly. The totalor trip mileages appear on the dis-
play. The pre-set service distance hasbeen exceeded. The spanner and total number of miles exceeded flash in the displayfor five seconds after the ignition isswitched on. For example:
the pre-set service
distance has been exceeded by
300 miles. Your vehicle must beserviced as soon as possible. Five seconds after switching on the ignition, the total mileage recorderreverts to normal operation and themaintenance spanner remains illu-minated.

INSTRUMENT PANEL*29I-12
Maintenance intervals If your vehicle is used in particular- ly harsh conditions, it is necessaryto select the maintenance sche-dules for Òarduous conditions ofuseÓ (see the Maintenance Guide)which consist of more frequent ser-vices. Note:the maintenence spanner will
come on, and the display will read ''0'' if the maximum length of time
between services is attained beforethe mileage limit is reached. To change the maintenance intervals:
- Switch off the ignition.
- Press and hold down button
1.
- Switch on the ignition.
- The distance remaining until the next service flashes.
- Release the button immediately.
- The maintenance interval is dis- played.
- Pressing button 1briefly allows
the maintenance intervals to be alternated. - When the desired maintenance
interval is displayed, press button1 for ten seconds to validate (the
selected maintenance interval willflash for ten seconds).
Release the button to validate whenthe display stops flashing. Resetting the maintenance indi- cator to zero
Your dealer will perform this opera-
tion after each service. However, ifyou intend to service the vehicleyourself, the procedure for resettingthe maintenance indicator is as fol-lows:
- Switch off the ignition.
- Press and hold down button 1.
- Switch on the ignition.
- The distance remaining until the next service flashes.
- Hold button 1down for ten
seconds.
- The display will read Ò=0Óand the
spanner will disappear.
* According to model or country
1
11

INSTRUMENT PANEL*I-12
30
Digital clock The clock can be set, with the ignition on and the engine not running , by pressing button Bfor more than three
seconds; the hour will start to flash. Changing the hour - Short press: allows the time to be changed slowly. Long press:allows the time to be changed quickly.
If the button is not pressed for five seconds: the hour is memorised, the minutes flash.
Changing the minutes- Short press: allows the time to be changed slowly. Long press:allows the time to be changed quickly.
If the button is not pressed for five seconds: the minutes are set.
Note: the clock display comes on when the driverÕs door is opened and goes out one minute after it is shut. The clock
display goes off after 10 minutes if the driverÕs door remains open.
* According to model or country
B

INSTRUMENT PANEL*I-12
34
Tachometer Do not enter the red zone. Display
¥ Outside temperature.
¥ Automatic gearbox display. Display
¥ Maintenance indicator.
¥ Total mileage recorder.
¥ Trip mileage recorder.
Fuel gauge Coolant temperature gauge
Display control:
¥ Total mileage recorder.
¥ Trip mileage recorder.
¥ Resetting the trip mileage recorder to zero.
Engine oil level
* According to model or country

INSTRUMENT PANEL*I-12
34
Tachometer Do not enter the red zone. Display
¥ Outside temperature.
¥ Automatic gearbox display. Display
¥ Maintenance indicator.
¥ Total mileage recorder.
¥ Trip mileage recorder.
Fuel gauge Coolant temperature gauge
Display control:
¥ Total mileage recorder.
¥ Trip mileage recorder.
¥ Resetting the trip mileage recorder to zero.
Engine oil level
* According to model or country

INSTRUMENT PANEL*I-12
36
* According to model or country
Protection fuses under the dashboardF2 - F19
A
Exterior temperature display The outside temperature is dis- played whenever the ignition isswitched on. If the ¡C symbol flashes, there is a danger of ice on the roads. Resetting the trip mileage recorder to zero Press button
Ato alternate the dis-
play between the total mileage
recorder and the trip mileage recorder. Press and hold down the button to reset the current trip mileage recor-der to zero. Dashboard lighting The intensity of the dashboard ligh- ting can be adjusted. Use the rheostat dimmer wheel located in the dashboard.