Change Peugeot Expert VU 2009 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009, Model line: Expert VU, Model: Peugeot Expert VU 2009Pages: 226, PDF Size: 10.49 MB
Page 112 of 226
108
Changing a wheel
4. OPERATING PROCEDURE Do not extend the jack until you have started
unscrewing the bolts on the wheel to be
changed and have placed the chock under
the wheel diagonally opposite.
- Remove the trim pulling it using the
embellisher remover.
- Loosen the wheel bolts and start unscrewing them.
- Place the jack in contact with the locating point provided, the one which is
closest to the wheel to be changed.
Ensure that the jack is straight and that the base of the jack is fully in contact
with the ground.
- Extend the jack to lift the wheel clear of the ground.
- Resume and complete the unscrewing of the wheel bolts.
- Remove the bolts and remove the wheel. Special tools for vehicles fitted with alloy
wheels
If your vehicle has wheels with alloy rims:
- The embellisher is removed using the
alloy wheel embellisher remover.
- Each wheel is fitted with an anti-theft bolt.
- These bolts can be loosened using your anti-theft socket (given to you
on delivery of your vehicle) and the
wheelbrace.
Page 116 of 226
111
Changing a bulb
TROUBLESHOOTING
7
CHANGING A BULB
Type A
Entirely glass bulb: pull
gently as it is fitted by
pressure.
Type B
Bayonet bulb: press
on the bulb then turn it
anticlockwise.
Type C
Halogen bulb: release
the retaining spring from
its housing.
TYPES OF BULB
Various types of bulb are installed on your vehicl e. To remove them: Halogen bulbs must be changed after
the headlamp has been off for several
minutes (risk of serious burns). Do not touch
the bulb directly with your fingers, use
lint-free cloths.
When each operation has been completed,
check the operation of the lights.
Page 117 of 226
112
Changing a bulb
3. Direction indicators
Type B, PY 21 W - 21 W (amber)
- Turn the bulb holder a quarter turn anticlockwise.
- Remove the bulb by pressing it lightly while turning it anticlockwise.
- Change the bulb.
- Ensure that the cover is refitted
correctly over its entire periphery to
guarantee sealing.
FRONT LIGHTS
Open the bonnet. To access the bulbs, reach
behind the headlamp unit.
Carry out the operations in reverse order to
refit each bulb.
1. Dipped headlamps/Main beam
headlamps
Type C, H4 - 55 W
- Remove the centre cover by pulling the flexible rubber tab.
- Disconnect the electrical connector.
- Release the retaining spring.
- Change the bulb taking care to align the metal part with the grooves on the light.
2. Side lights
Type A, W 5 W - 5 W
- Remove the cover by pulling the flexible rubber tab.
- Remove the bulb holder fitted by pressure by pulling the connector.
- Change the bulb.
- Ensure that the cover is refitted correctly over its entire periphery to
guarantee sealing.
4. Fog lamps
Type C, H1 - 55 W
Consult a PEUGEOT dealer.
Page 118 of 226
113
Changing a bulb
TROUBLESHOOTING
7
DIRECTION INDICATOR SIDE
REPEATER
Type A, WY 5 W (amber)
- Push the repeater towards the rear and disengage it.
- Support the connector and turn the bulb holder a quarter turn to the left.
- Turn the bulb a quarter turn to the left, remove it and change it.
- When refitting, engage the repeater towards the rear and bring it towards the
front.
Front/Rear
Amber coloured bulbs (direction indicators
and side repeaters) must be replaced with
bulbs of identical specification and colour. COURTESY LIGHTS
Type A, 12 V 5 W - 5 W
- Unclip the lens by sliding a screwdriver in the slots on each side of the courtesy
light.
- Pull the bulb and change it.
- Clip the lens in its housing and ensure that it is secured correctly. High pressure washing
When using this type of washing on
stubborn dirt, do not persist on the
headlamps, the lights and their surrounds to
avoid damaging their coating and their seal.
Page 119 of 226
114
Changing a bulb
REAR LIGHTS
For further information concerning the bulbs,
refer to the "Types of bulb". - Identify the faulty bulb then open
the rear doors to 180°. Refer to the
"Accesses" section of chapter 2.
- Remove the two fixing nuts.
Pull the lens block from the outside.
- Holding the light, disconnect the electrical connector. - Move aside the 8 tabs then extract the
bulb holder.
- Remove the faulty bulb by pressing it lightly while turning it anticlockwise.
- Change the bulb.
1. Brake lights/side lights
Type B, P21/5 W - 21/5 W
2. Direction indicators
Type B, PY 21 W - 21 W (amber)
3. Reversing lights
Type B, P21 W - 21 W
4. Fog lamps
Type B, P21 W - 21 W When refitting, take care to correctly
reposition:
- the 8 tabs,
- the two white lugs in the two rubber
holes to maintain the sealing of the light,
- the supply wire to avoid trapping it.
Page 120 of 226
115
Changing a bulb
TROUBLESHOOTING
7
THIRD BRAKE LIGHT
Type A, W 5 W - 5 W
NUMBER PLATE LIGHTS
Type A, W 5 W - 5 W
Light located on the inside (tailgate)
- Unscrew the two screws using a Torx TM
screwdriver with 20 socket.
- Remove the plastic cover.
- Remove the bulb holder moving aside the two tabs.
- Remove the faulty bulb by pressing it lightly while turning it anticlockwise.
- Change the bulb.
Type B, P21 W - 21 W
With tailgate
- Move aside the plastic lens using a
screwdriver, on the point indicated by
the arrow.
- Change the bulb.
- Replace the plastic lens and press on it.
With hinged doors
- Unclip the interior trim.
- Disconnect the connector by moving aside its tab.
- Remove the plastic cover.
- Turn the bulb holder a quarter turn anticlockwise.
- Change the bulb. Light located on the outside (hinged doors)
- Unscrew the two screws using a Torx
TM
screwdriver with 20 socket.
- Remove the light.
- Change the bulb.
Type B, P21 W - 21 W
Light on high door
- Remove the screws using an 8 wrench.
- Remove the faulty bulb by pressing it lightly while turning it anticlockwise.
- Change the bulb.
Page 121 of 226
116
Changing a fuse
CHANGING A FUSE
The three fuse boxes are placed:
- in the fascia panel on the right-hand side (behind the storage compartment,
retractable),
- in the passenger compartment (battery compartment),
- under the bonnet.
If fitted on your vehicle, a further fuse
box is added for towing, the towbar and
the connections for the coachbuilder and
platform cab conversions. It is located on the
right behind the load retaining partition.
Removing and fitting a fuse
Before changing a fuse, the cause of the
fault must be found and rectified.
- Use the pliers.
Always replace a faulty fuse with a fuse
of the same rating.
PEUGEOT will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying the malfunctions
resulting from the installation of accessories
not supplied and not recommended by
PEUGEOT and not installed in accordance
with its instructions, in particular when
the combined consumption of all of the
additional equipment connected exceeds
10 milliamperes.
The descriptions communicated are only
the fuses which can be changed by the
user using the pliers and replacement fuses
located behind the fascia panel storage
compartment on the right-hand side. For any
other operations, visit a PEUGEOT dealer.
Intended for professionals: for
complete fuse and relay information,
consult the "Methods" diagram via the
Network.
Page 122 of 226
117
Changing a fuse
TROUBLESHOOTING
7
RIGHT-HAND SIDE FASCIA PANEL FUSES
- Tilt the storage compartment then pull it firmly to access the fuses.
Fuses A (amps) Allocation
1 15 Rear wiper
2 - Free
3 5 Air bag control unit
4 10 Steering wheel angle sensor, Diagnostic socket,
ESP sensor, Manual ventilation, Clutch switch,
Headlamp beam height, Particle emission filter pump
5 30 Electric mirrors, Passenger electric window mot or
6 30 Front electric windows supply
7 5 Courtesy lights and glove box light
8 20 Multifunction display, Anti-theft alarm siren, Aud
io
equipment, Compact disc changer, Audio/telephone,
Trailer fuse box (accessory), Coachbuilder/vehicle modifier
unit (platform cab)
9 10 Load space accessories socket
10 30 Rear ride height corrector, Steering wheel switchi
ng,
Instrument panel
11 15 Diagnostic socket, Ignition switch
12 15 Hands-free kit, Air bag control unit, Parking assi
stance
control unit
13 5 Engine fuse box, Trailer fuse box
14 15 Rain sensor, Automatic air conditioning, Instru ment panel
15 30 Locking/unlocking/deadlocking of the accesses
16 - Free
17 40 Heated rear screen, Heated mirrors
17 10 Heated mirrors only
Page 165 of 226
9.24
11
2 2
11
3 3
2 2
CD CHANGER
I n s e r t t h e C D s i n a m u l t i - s l o t c h a n g e r ( n o t M P 3 c o m p a t i b l e ) o n e b y o n e . O n a s i n g l e s l o t c h a n g e r ( M P 3 c o m p a t i b l e ) , p r e s s L O A D , s e l e c t t h e number of the CD, then insert the CD, o r p r e s s a n d h o l d L O A D a n d i n s e r t the CDs one by one.
P r e s s t h e S O U R C E b u t t o n s e v e r a l times in succession and select C D C H A N G E R .
Press one of the buttons on the alphanumeric keypad to select the c o r r e s p o n d i n g C D .
Press one of the buttons to select a track on the CD.
I t i s n o t p o s s i b l e t o c o p y t h e fi l e s o n t o t h e h a r d d i s c f r o m t h e C D c h a n g e r .
CD CHANGER
PLAYING A CD
P r e s s t h e M E N U b u t t o n t h e n s e l e c t t h e C O N F I G U R A T I O N f u n c t i o n , t h e n S O U N D S , t h e n A C T I V A T E A U X I L I A R Y S O U R C E t o a c t i v a t e the audio equipment auxiliary input.
Connect the portable equipment ( M P 3 p l a y e r … ) t o t h e J A C K s o c k e t o r to the audio sockets (white and red, R C A t y p e ) l o c a t e d i n t h e g l o v e b o x u s i n g a s u i t a b l e c a b l e .
P r e s s t h e S O U R C E b u t t o n s e v e r a l times in succession and select AUX.
T h e d i s p l a y i n g a n d m a n a g e m e n t o f t h e c o m m a n d s t a k e s p l a c e v i a the portable equipment.
I t i s n o t p o s s i b l e t o c o p y t h e fi l e s o n t o t h e h a r d d i s c f r o m t h e a u x i l i a r y input.
USING THE AUXILIARY INPUT (AUX)
JACK/RCA AUDIO CABLE NOT SUPPLIED
Page 201 of 226
1
2
3
4
1
4
0 6
2
3
5
9.57
C o n n e c t t h e p o r t a b l e e q u i p m e n t ( M P 3 / W M A p l a y e r … ) t o t h e a u d i o C o n n e c t t h e p o r t a b l e e q u i p m e n t ( M P 3 / W M A p l a y e r … ) t o t h e a u d i o s o c k e t s ( w h i t e a n d r e d , R C A t y p e ) i n t h e g l o v e b o x u s i n g a s o c k e t s ( w h i t e a n d r e d , R C A t y p e ) i n t h e g l o v e b o x u s i n g a J A C K / R C A a u d i o c a b l e .
Press the MUSIC button then press i t a g a i n o r s e l e c t t h e M U S I C M E N U f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
Select the AUX music source and p r e s s t h e d i a l t o c o n fi r m . P l a y b e g i n s automatically.
S e l e c t t h e E X T E R N A L D E V I C E function and press the dial to activate it.
E X T E R N A L D E V I C E
Insert one or more CDs in the c h a n g e r . P r e s s t h e M U S I C b u t t o n .
Press one of the buttons on the numeric keypad to select the c o r r e s p o n d i n g C D .
S e l e c t t h e C D C H A N G E R m u s i c s o u r c e a n d p r e s s t h e d i a l t o c o n fi r m .
T h e d i s p l a y i n g a n d m a n a g e m e n t o f t h e c o n t r o l s a r e o p e r a t e d v i a t h e T h e d i s p l a y i n g a n d m a n a g e m e n t o f t h e c o n t r o l s a r e o p e r a t e d v i a t h e portable equipment.
CD CHANGER
S e l e c t t h e S E L E C T M U S I C f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
U S I N G T H E E X T E R N A L D E V I C E ( A U X )
AUDIO/RCA CABLE NOT SUPPLIED
CD CHANGER
P L A Y I N G A C D ( N O T M P 3 / W M A C O M P A T I B L E )
SELECT MUSIC
P r e s s t h e M U S I C b u t t o n a g a i n o r s e l e c t t h e M U S I C M E N U f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
MUSIC MENU
MUSIC MEDIA PLAYERS