wheel Peugeot iOn 2012 - RHD (UK, Australia) User Guide

Practical information
94
Repair procedure
1. Sealing
FSwitch off the ignition.FIndicate on the speed restriction sticker provided, the wheel to be repaired, then fix it to the steering wheel as a reminder that a
wheel is in temporary use. FShake the sealant car tridge, remove the cap and screw on the injection pipe.
F Remove the valve cap for the tyre to be
repaired.F Remove the valve core using the tool
provided, and store in in a clean place.
F Connect the injection pipe to the valve of
the tyre to be repaired.
FTap the sealant car tridge (top down)several times with your hand, so as to injectall of the product into the tyre. FRemove the injection pipe.FRefit the valve core and tighten it using the
tool provided.

Take care, this product is harmful (e.g. ethylene-glycol, colophony...) if swallowed andcauses irritation to the eyes.Keep it out of reach of children. The use-by date of the sealant is marked on the car tridge.
After use, do not discard the empty cartridge but take it to a PEUGEOT dealer (France) or
an authorised waste disposal site. Don't forget to obtain a replacement cartridge; they are available from a PEUGEOT dealer or a qualified workshop.

Avoid removing any foreign bodieswhich have penetrated into the tyre.

8
Practical information
95

2. Infl ation
FCheck that the compressor switch A
is in
the "OFF" position. FUncoil the compressor pipe B.
F
Connect this pipe to the valve of the
repaired wheel. F
Connect the compressor's electric plug to
the vehicle's 12 V socket (ignition switch in
position "ON" or "ACC"). F Star t the compressor by turning the
switch A
to the "ON" position. F
Using the compressor, adjust the pressure in accordance with the vehicle's tyre
pressure label (located in the driver's door
aperture).
A loss of pressure indicates that the
puncture has not been fully plugged;contact a PEUGEOT dealer or a qualified
workshop for assistance.
F Remove the compressor and stow the kit. F
Drive off straight away at reduced speed (50 mph [80 km/h] max) limiting
the distance travelled to approximately120 miles (200 km).



As soon as possible, go to a PEUGEOT dealer or a qualified workshop. Tell the technician that you have used the kit. After checking, the technicianwill advise you whether the tyre can berepaired or must be replaced.


If after around 5 to 7 minutes the pressure is not attained, this indicates that the tyre is not repairable; contacta PEUGEOT dealer or a qualifiedworkshop for assistance.

Practical information
96











Changing a wheel


To o l s r equired



- A jack: for lifting the vehicle.

- A wheelbrace: for removin
g and refitting
the wheel bolts.

- A handle: for operating the jack.
These tools are not supplied with your vehicle.
Parking the vehicle

Immobilise the vehicle where it does notblock traffic: the ground must be level,stable and not slippery. Apply the parking brake, switch off the ignition and put the drive selector
in position Pto lock the wheels.
If necessary, place a chock under thewheel diagonally opposite the wheel to be changed.
You must ensure that the occupants get out of the vehicle and wait where they are safe. Never go underneath a vehicle raised using a jack; use an axle stand.

Wheel with wheel trim
When removing the wheel , firstremove the wheel trim using the wheelbrace, by pulling at the valve hole.When fitting the wheel, refit the wheeltrim star ting by aligning the valve hole
with the valve, and then press on theedge of the trim with the palm of your hand.

8
Practical information
97
FSlacken the bolts using the wheelbrace.FPlace the jack in contact with one of the
two front A or rear B
locations provided on
the underbody, whichever is closest to the
wheel to be changed.

Removing the wheel
F
Using the handle, extend the jack until its base plate is in contact with the ground.
Ensure that the centreline of the jack base
plate is directly below the location A or Bused.F
Raise the vehicle until there is sufficientspace between the wheel and the ground.
F
Remove the bolts and store them in a clean place. F
Remove the wheel.

Practical information
98
Fitting the wheel
FPut the wheel in place on the hub. FScrew in the bolts by hand.FPre-tighten the bolts using the wheelbrace.

F
Lower the vehicle fully. F
Fold the jack and detach it.FTighten the bolts using the wheelbrace.



After changing a wheel

Have the tightening of the bolts andthe pressure of the new wheel checked by a PEUGEOT dealer or a qualifiedworkshop without delay.

8
Practical information
103
Changing dipped beam headlamp bulbs
FTurn the bulb holder to the left and pull it out. FRemove the bulb by pressing on the
tongue.FChange the bulb.
To r efit, carry out these operations in reverse order.
Changing front foglamp bulbs / daytime running lamp bulbs
F Put the front wheels onto full lock, to facilitate access.F
Remove the clips securing the protective covers on the bulb holders.F
Move the cover aside.
F
Turn the bulb holder ( Afor the front fog
lamp, B for the daytime running lamp) to
the left and pull it out.
F Pull the bulb out and change it.
To reassemble, carry out these operations in
reverse order.

Practical information
112





Towing the vehicle
Procedure for having your vehicle towed using fixed mechanical equipment.


To w i ng your vehicle

The towing eye is welded to the body below thefront bumper.F
Install the towing bar. F
Start your vehicle ("Ready" lamp on).F
Put the drive selector in position N . F
Release the parking brake.F
Switch on the hazard warning lamps onyour vehicle.F
Have your vehicle towed for no more than 20 miles (30 km) without exceeding a
speed of 20 mph (30 km/h) .


When towing the vehicle with the four wheels on the ground, always use a towing bar.
When towing with only two wheels onthe ground, use professional lifting equipment.


Failure to follow these instructions may cause damage to braking components and the electric motor.









Changing a wiper
blade
Removing a front or rear
wiper blade
FRaise the corresponding wiper arm.FRemove the wiper blade, sliding it towards
the outside.
Fitting a front or rear wiper
blade
FPut the new wiper blade in place and
secure it. FFold down the wiper arm carefully.



To w i ng another vehicle

Your vehicle cannot be used in any circumstances to tow another vehicle.

8
Practical information
113





Accessories

A wide range of accessories and genuine par ts is available from the PEUGEOT dealer network.
These accessories and par ts have been tested and approved for reliability and safety.
They are all adapted to your vehicle and benefit from PEUGEOT's recommendation and warranty.
Conversion kits
You can obtain an "Enterprise" kit to conver t a
trade vehicle to a private car and vice-versa.
"Comfort":
black armrest, reading lamp, insulated
modules, rear parking sensors, cigarette lighter,ashtray with base, head restraint mounted coathanger...

"Transport solutions":

boot liner, boot carpet, rear parcel shelf, boot dividers...


"Security and safety":

alarm, wheel security bolts, child seats,
breathalyzer, warning triangle, high visibility
vest, first aid kit, snow chains, non-slip covers,
pet transpor t ca
ge, pet safety belt...
Precautions for
washing
To avoid damaging the electrical components, the use of a high pressure jet wash is strictly prohibited:


- in the front compar tment (under thebonnet),

- under the body.

For washing the body, do not use a pressure greater than 80 bars.
Check - before washing the vehicle -that the charging flaps and the charging socket covers (normal and fast charge) are properly closed.


Do not wash the vehicle while the
battery is being recharged.

10
Technical data
125














Identifi cation markings
Various visible markings for the identification of your vehicle.
A. Ser vice - Replacement Par ts
identification plate.
This plate is riveted to the underside of thebonnet.
Tyre pressures must be checked whenthe tyres are cold, at least once amonth.

Low tyre pressures increase the
electrical power consumption of your vehicle, which reduces its range. B. Tyre identification label
.This label is affixed to the driver's centre pillar.
It bears the
following information:
- the tyre pressures (in bars),
- the tyre specification,
- the type of tyre.C. Manufacturer's
plate This plate is riveted to the left hand centre pillar.
D. Vehicle identification number (VIN).
This number is is engraved on the inner wheel
arch, inside the boot, right hand side.
For information on fitting snowchains, contact a PEUGEOT dealer or a qualified workshop.
It bears in par ticular the
following information:


- the vehicle model,

- the paint code,

- the type, variant, version.

.
Visual search
153
Exterior
Remote control key 31- 32- opening / closing- central locking- anti-theft protection Starting - Stopping the vehicle 53
Lighting 57-59 Headlamp height adjustment 59 Changing bulbs 99 -104- front lamps- foglamps - daytime running lamps- direction indicator repeaters

Wipers 60Changing a wiper blade 112
Door mirrors 42
Doors 35 - opening / closingElectric windows 34
Charging flaps 37 Charging the main battery 82-87- normal- fast



Accessories 113

ABS, EBFD, EBA, ASR, ESP 72-74 Tyre pressures 125Changing a wheel 96 -98
Boot 36- opening / closing
Changing bulbs 10 4 -10 6- rear lamps- 3rd brake lamp - number plate lamps- foglamp
Recovery 112