transmission Peugeot iOn 2017 Owner's Manual - RHD (UK, Australia)

47
Remote control*
This is used for remote control of the following
functions:
-
C
heck of the vehicle charge status.
-
P

rogramming of charging: start time and
duration of charging.
-

A
ctivation of the climate control functions
(heating, air conditioning, demisting).
In order to programme charging, the
following conditions must be met.
-

P
lace the drive selector in
position


P.
-

P
lace the switch on LOCK .
-

C
onnect the vehicle using the
normal charging cable.Buttons Display
1. On/Off, transmission of data.
2. M
ODE: used to scroll through the various
functions available (start of charging,
duration of charging, interior temperature).
3.
I

mmediate charging of the vehicle
(resetting of the programming values to
ze r o).
4.
S

ettings. 1.
D

ata transmission status indicator lamp.
2.
C

harging indicator lamp.
3.
F

ault warning lamp.
4.
B

attery charge status warning lamp.
5.
C

harging programming functions status
indicator lamp.
6.
C

harging time remaining indicator.
7.
In

terior temperature function status
indicator lamp.
The remote control has a range of
approximately 100 metres.
* Depending on equipment.
3
Ease of use and comfort

51
Operating faults
Remote control
Indicator lampsStatus CausesActions / Observations
Flashes within approximately 10 seconds
after the remote control is switched on. A fault has occurred.
Switch the remote control off, then on
again.
Flashes within approximately 1 second
after the remote control is switched on. Electrical interference is preventing the
operation of the remote control or the
transmission of data.Move away from the sources of
interference.
Flashes within approximately 10 seconds
after the remote control is switched on. The aerial has not been extended.
Extend the aerial.
The range of the remote control has
been exceeded. Move closer to the vehicle.
The switch is not in the LOCK position. Place the switch in the LOCK position.
3
Ease of use and comfort

148
Select "Radio". Select "Radio"
.
Select "Radio" .
Select or deselect "RDS" to switch
RDS on or off. Select or deselect "
TXT" to
activate or deactivate the display
of "R ADIO TEXT".
Select or deselect " TA" to activate
or deactivate the reception of traffic
messages.
Confirm with "OK" to save the
setting. Confirm with "OK"
to save the
setting.
Confirm with "OK" to save the
setting.
Receiving TA messages
RDS Displaying "RADIO TEXT"
The TA (Traffic Announcement)
function gives priority to TA alert
messages. To operate, this function
needs good reception of a radio station
transmitting this type of message.
When a traffic report is transmitted, the
current audio source (Radio, CD, USB,
etc.) is interrupted automatically to play
the TA message. Normal playback of
the audio source resumes at the end of
the transmission of the message.
RDS, if activated, enables you to continue
listening to the same station by automatic
retuning to alternative frequencies.
However, in certain conditions, coverage
of an RDS station may not be assured
throughout the country as radio stations
do not cover 100

% of the territory. This
explains the loss of reception of the
station during a journey. "R ADIO TEXT" is information
transmitted by the radio station related
to the current programme or song.
With source FM1 or FM2,
press

MENU . With the radio displayed on the
screen, press MENU
.
Press MENU .
Audio and Telematics

151
Use only USB memory sticks formatted to
FAT32 (File Allocation Table).The use of genuine Apple
® USB cables
is recommended to ensure correct
operation.
On a single disc, the CD player can read up
to 255 MP3 files spread over 8 folder levels
with a maximum of 192 folders. However, it is
recommended that this be kept to 2 levels so
as to limit the time taken to access and play
the CD.
During play, the folder structure is not
observed.
Do not connect a hard disk or USB device other
than audio players to the USB port. This may
cause damage to your installation.
To protect the system, do not use a
USB hub.
Bluetooth® audio streaming
Streaming allows music files on a telephone to
be heard via the vehicle's speakers.
Connect the telephone: see the " Telephone"
section.
In the " Bluetooth : Audio" menu, select the
telephone to connect.
The audio system connects automatically to a
newly paired telephone.
The control of common tracks is possible
via the audio system control buttons and
the steering mounted controls**. Contextual
information can be displayed in the screen. Activate the streaming source by
pressing the SRC/TEL
* button.
The audio quality depends on the quality of the
transmission from the telephone.
*

I
n certain cases, the playing of audio files
must be initiated from the telephone.
** If the telephone supports the function.
Connecting Apple® players
Connect the Apple® player to the USB port
using a suitable cable (not supplied).
Play starts automatically.
Management of the device is via the audio
system controls.
The classifications available are those on the
portable player connected (artists / albums /
genres / playlists / audiobooks / podcasts).
The software version of the audio system may
not be compatible with the generation of your
Apple
® p l aye r.
.
Audio and Telematics