turn signal Peugeot iOn 2017 Owner's Manual

12
Ion_en_Chap01_instruments-de-bord_ed01-2016
Operation indicator lamps
Warning / indicator lampStateCause Action / Observations
Left-hand
direction indicatorFlashing with audible
signal. The lighting stalk is pushed down.
Right-hand
direction indicator Flashing with audible
signal. The lighting stalk is pushed up.
Hazard warning
lamps Flashing with audible
signal. The hazard warning lamps switch,
located on the dashboard, has been
operated. The left-hand and right-hand direction indicators and
their associated indicator lamps flash simultaneously.
Sidelamps and/
or dipped beam
headlamps On fixed.
The sidelamps and/or dipped beam
headlamps are on.
Front foglamps On fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off
the front foglamps.
Rear foglamp On fixed. The rear foglamp is switched on. Turn the ring on the stalk rear wards to switch off the
rear foglamp.
Main beam
headlamps
On fixed.
The lighting stalk is pulled towards
you. Pull the stalk to return to dipped beam headlamps.
If one of the following indicator lamps comes on in the instrument panel, this confirms that the corresponding system has come into operation.
Instruments

54
Ion_en_Chap04_eclairage-et-visibilite_ed01-2016
Front and rear foglamps
Foglamps selection ring.
The foglamps operate with the sidelamps and
dipped and main beam headlamps.Front and rear foglamps.
In good or rainy weather, both day
and night, the front foglamps and the
rear foglamp is prohibited. In these
situations, the power of its beam may
dazzle other drivers.
Do not forget to switch off the front
foglamps and the rear foglamp when
they are no longer necessary.
Lighting on reminder
There is an audible signal when the
driver's door is opened, to warn the
driver if the vehicle lighting is on, with
the ignition off.
Switching off the lighting stops the
audible signal.
F

T

o switch on the front foglamps, turn the
ring forwards once.
F

T

o switch on the rear foglamp, turn the ring
forwards twice.
F

T

o switch off the rear foglamp, turn the ring
rearwards twice.
F

T

o switch off the front foglamps, turn the
ring rearwards once.
The ring returns to its initial position
automatically.
The rear foglamp is switched off automatically
when you switch off the sidelamps, or the
dipped or main beam headlamps.
Lighting and visibility

67
Ion_en_Chap05_securite_ed01-2016
Seat belts
Front seat belts
Fastening
F Pull the strap, then insert the tongue in the buckle A .
F

C
heck that the seat belt is fastened
correctly by pulling the strap.
Front seat belt not fastened /
unfastened warning lamp
If the driver does not fasten their seat belt
within one minute after switching on the
ignition, the warning lamp flashes accompanied
by an intermittent audible signal.
After about 90 seconds, the warning lamp, the
audible signal and the display stop, and then
return until the driver fastens their seat belt.
If the seat belt is unfastened while the vehicle
is moving , you are warned by the same alerts.
The front seat belts are fitted with a
pretensioning and force limiting system.
This system improves safety in the front
seats in the event of a front or side impact.
Depending on the severity of the impact, the
pretensioning system instantly tightens the seat
belts against the body of the occupants.
The pretensioning seat belts are active when
the ignition is on.
The force limiter reduces the pressure of the
seat belt on the chest of the occupant, so
improving their protection.
Unfastening
F Press the red button on the buckle A
.
When the ignition is switched on, this
warning lamp comes on accompanied
by an audible signal for a few seconds
if the driver and/or passenger has not
fastened their seat belt.
5
Safety

88
Ion_en_Chap06_conduite_ed01-2016
Starting - stopping the vehicle
- Position 1: LOCK The steering is locked.
-

P
osition 2 : ACC
T

he ancillaries (radio, 12 V socket, etc.)
can be used.
-

P
osition 3: ON
I

gnition on.
-

P
osition 4: S TA R T
"

Ready" lamp on.
M

otor ready to drive the vehicle.
Ignition switch
F Check that the drive selector is in position P.
F

I
nsert the key in the ignition switch.
F

T
urn the key to position 4 (S TA R T ) .
StartingStopping
F Stop the vehicle.
F
K eep your foot on the brake pedal.
F

P
lace the drive selector in position P .
F

A
pply the parking brake.
F

T
urn the key to position 1 (LOCK) .
F

R
emove the key from the ignition switch.
F

H

old it in this position for a few
seconds until the " RE ADY " lamp
comes on accompanied by an
audible signal.
F

R

elease the key.
T

he key returns automatically to
position


3


(ON) . Do not attach any heavy objects to the
key as this could weigh down on it when
in the ignition switch and cause a fault.
If you use the ancillaries for a prolonged
period (with the key in the ACC
position), you risk discharging the 12 V
battery. Starting your vehicle will then
no longer be possible. Be aware .
Driving