battery PEUGEOT PARTNER 2014 Owners Manual

3
Partner-2-VU_en_Chap00a_Sommaire_ed02-2014
corresponds to
a left hand drive
vehicle.corresponds to a
right hand drive
vehicle.
10.
TECHNOLOGY on
BOARD
6.
107-1

10
ACCESSORIES

7.


111-128
CHECKS
8.
129-149
QUICK HELP

Emergency or assistance 10.1
PEUGEOT
Connect
Navigation (RT6)

10.3PEUGEOT Connect Sound 10.59
T
owing a trailer

107
Other accessories


109
T

rade range
Telematic unit
Opening the bonnet

1

12
Petrol engine

1

13
Diesel engine

1

14
Levels

1

15
Checks

117
Fuel

119
Fuel cut-off

120
Diesel priming pump


120
AdBlue® additive and
SCR system
(BlueHDi Diesel)

121Battery

129
Changing a wheel
131
Removable

snow screen
135
Snow chains

136
Changing a bulb

137 a fuse


142 a wiper blade


146
Being towed

147
Precautions
148
9.
150-156
TECHNICAL

DATA
Dimensions 150
Engines 155
W
eights
155
Identification markings


156The "T

echnology on board"
section presents the new
audio/navigation systems.
P EUGEOT
Connect is the
name given to all of the
new equipment of the radio/
navigation range.
Contents
CONTENTS

5
Partner-2-VU_en_Chap01_vue-ensemble_ed02-2014
EXTERIORRemote control 18-19
Changing the battery ,
reinitialisation

19
Key


18
Starting


50
Hill start assist


51
Central locking /


unlocking

18, 27
Locking / unlocking


the load space

18, 27
Filler cap, fuel


tank
119-120
Fuel cut-off, Diesel priming
120
AdBlue additive, topping up

121-125, 126-128
Wiper blades


146
Door mirrors


82-83
Side repeater


139
Front lamps, foglamps, direction indicators


52-54, 137-139Headlamp beam height adjustment 54
Changing front bulbs 137-139
Headlamp wash

56, 1
16
Snow cover

135
Front doors


21
Sliding side door


22
Key


18
Opening the bonnet


1
12
Inflation, pressures

156
T

owing, lifting

147
T

owbar

107-108
Rear parking


sensors

86-87
Number plate


lamp

141
Spare wheel, jack,


changing a wheel,
tools

131-135
Rear lamps,
direction indicators 52-53, 140-141
3rd brake lamp
141
Changing rear

bulbs

137, 140-141
Load space,


opening

18, 27
Doors, tailgate


23-24, 26
Accessories

109-110
Roof bars

81
Rear roof flap


25
Emergency control


26 Dimensions


150-153
Floor cab

dimensions
154
Brakes, pads

85, 1
15, 117
Emergency braking

88
ABS, EBFD


88
ASR, DSC


89
"Grip control"


90-91
T

yre, pressures
156Tyre under-inflation detection 39-40
Snow chains
136
1
OVERVIEW
Location

6
Partner-2-VU_en_Chap01_vue-ensemble_ed02-2014
Rear view mirror 83
Front courtesy lamp 76
Changing courtesy

lamp bulbs

139
Spare wheel, jack,


changing a wheel,
tools

131-135
Snow chains


136 Front, lateral airbags


94-97
Passenger's airbag


deactivation

97, 100
Battery

, recharging,
starting
129
Opening the bonnet

1

12
Towing, towbar, coachbuilders,
floor cab fuses

144
Front seats, adjustments,


head restraint

69-70
Multi-Flex bench seat


71-72
Seat, bench


configurations

73
Seat belts


92-93
Accessories

109-110
INTERIOR
Rear courtesy lamp 76
Changing courtesy
lamp bulbs

139
Load space


79-81
-


stowing rings,
-


load retainer
,
-

trim,
-


12 volt socket,
-


ladder separation or partition,
-


removable flap. Child seats


98-106
Parking brake,

handbrake
85
T
owing, lifting
147
T

owbar
107-108
T

owed loads
155
Location

7
Partner-2-VU_en_Chap01_vue-ensemble_ed02-2014
INTERIOR
Rear view mirror 83
Front courtesy lamp 76
Changing courtesy

lamp bulbs

139
Spare wheel, jack,


changing a wheel,
tools

131-135
Snow chains


136 Front, lateral airbags


94-97
Passenger's front airbag deactivation


97, 100
Battery

, recharging,
starting
129
Child seats

98-106
Parking brake,


handbrake

85 Front seats, adjustments,


head restraint

69-70
Multi-Flex bench seat


71-72
Seat, bench


configurations

73
Seat belts


92-93
T

owing, lifting
147
T

owbar
107-108
T

owed loads
155
Rear courtesy lamp


76
Changing courtesy lamp


bulbs

139
Load space


79-81
-


stowing rings,
-


load stop,
-


trim,
-


12 volt socket,
-


ladder separation or partition,
-


removable flap.
Opening the bonnet


1

12
Accessories

109-1
10
Towing, towbar,
coachbuilders, floor
cab fuses

144
1
OVERVIEW
Location

14
Partner-2-VU_en_Chap01_vue-ensemble_ed02-2014
TECHNICAL DATA - MAINTENANCE
Identification markings, serial number, paint code,
tyres

156
Snow chains


136
Windscreen / headlamp wash, levels

116
Changing bulbs, lighting
137-141 Checks
117-118
-

battery
,
-

gearbox,- air/passenger compartment filter,- oil filter,
-
particle filter ,
-

parking brake,
-


brake pads,
-


brake drums, discs.
Emissions controls


39
Engine fuses


142, 145
Under the bonnet: -


Diesel

1
14
-

petrol

1
13
Fuel cut-off, Diesel priming
120
AdBlue additive

121-128
Opening the bonnet, stay


1

12 Levels

1
15-116
-
Diesel additive,
-

dipstick,
-

power steering fluid,
-

brake fluid,
-

coolant.
Bleeding water
, Diesel filter
1
18
Warning lamps

30-37
Dimensions


150-153
Floor cab dimensions


154
Engines / W

eights

155
Location

19
Partner-2-VU_en_Chap03_Pret-a-partir_ed02-2014
Good practice
Take care not to allow the remote
control to come into contact with
grease, dust, rain or a damp
environment.
A heavy object attached to the key
(keyring, ...) weighing on the shaft of
the key in the switch, may cause a
malfunction.
REMOTE CONTROLReinitialising the remote control
Following changing of the remote
control battery or disconnection of the
vehicle battery, the remote control may
have to be reinitialised.
Wait at least one minute before using
the remote control.
Insert the key in the ignition switch with
the buttons (padlocks) of the remote
control facing you.
Switch on the ignition.
Press the locking padlock for at
least five
seconds within the next
ten
seconds.
Switch off the ignition.
Wait at least one minute before using
the remote control.
The remote control is now working
again.
Use only identical batteries or
batteries of an equivalent type to those
recommended by PEUGEOT dealers.
Do not discard the remote control
batteries, they contain metals which
are harmful to the environment.
Deposit them at a PEUGEOT
dealership, or at an authorised
collection point.
Folding / unfolding the key
Changing the battery
Battery ref.: CR1620 / 3 volts.
The "battery flat" information is given
by an audible signal, accompanied by
a message in the screen.
T
o replace the battery, unclip the
casing using a coin at the ring.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
There is a risk of damage if the
replacement battery is not the correct
type. Press this button to release
the key from its housing.
To fold the key, press this
chromed button then fold
the key into the housing.
If you do not press the button, the
mechanism may be damaged.
Access
READY TO SET OFF
3

22
Partner-2-VU_en_Chap03_Pret-a-partir_ed02-2014
From the inside
Unlock and open the side door using
this handle, guiding the rearward
sliding to the point of resistance. Pass
this point to hold the door open.
Good practice
Take care not to block the guide space
on the floor to allow the door to slide
correctly.
If your vehicle is parked on a slope,
guide the sliding of the side door. In
fact, the door could open or close more
rapidly due to the slope of the ground
and could cause injury.
For safety and operation reasons, do
not drive with the sliding side door
open.
SLIDING SIDE DOOR
From the outside
Pull the handle towards you then
towards the rear and open the side
door, guiding the rearward sliding to
beyond the point of resistance to hold
it open.
Operation in the event of
a battery failure
Front and side passenger doors
In the event of a battery or of the
central locking fault, use the lock to
lock the doors mechanically.
-

T
o open the door and get out of the
vehicle, pull the interior control.
-

T
o lock the door, insert the key in
the lock, located on the edge of the
door, then turn it one eighth of a
turn.
Driver's door
-

Insert the key in the lock, then turn
it to the right to lock or to the left to
unlock.
Access

32
Partner-2-VU_en_Chap03_Pret-a-partir_ed02-2014Partner-2-VU_en_Chap03_Pret-a-partir_ed02-2014
Warning lamp isindicatesSolution - action
Front / lateral
airbag flashing or
remaining on.
a failure of an airbag. Have the system checked by a PEUGEOT
dealer or a qualified workshop without delay.
Chapter 5, "Airbags" section.
Front
passenger's
airbag
deactivated on. the intentional deactivation
of this airbag in the
presence of a rearward
facing child seat. Chapter 5, "Airbags" or "child safety" section.
Low fuel
level on with gauge
needle in the
red zone. When it first comes on,
there remains around 8
litres of fuel in the tank. The
distance you can drive on
this fuel depends on your
style of driving and the
engine type. You must fill up with fuel to avoid running out.
This warning lamp comes on each time you
switch on the ignition until you have filled up.
Capacity of the tank: approximately 60 litres.
Never risk driving until the tank is empty, this
could damage the emissions and injection
systems.
flashing. cutting off of the fuel supply
following a serious impact. Restore the supply.
Chapter 7, "Fuel" section.
EOBD
emission
control systemflashing or
remaining on.
a failure of the system. There is a risk of damage to the catalytic
converter. Have it checked by a PEUGEOT
dealer or a qualified workshop.
Battery
charge on.
a fault in the charging
circuit. Check the battery terminals, …
Chapter 8, "Battery" section.
flashing. placing of the active
functions on standby
(economy mode). Chapter 8, "Battery" section.
remaining on,
in spite of the
checks. an ignition or injection
malfunction.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Instruments and controls

42
Partner-2-VU_en_Chap03_Pret-a-partir_ed02-2014Partner-2-VU_en_Chap03_Pret-a-partir_ed02-2014
Trip recorder zero reset button
After this operation, if you wish to
disconnect the battery, lock the
vehicle and wait for at least five
minutes, otherwise the zero re-set will
not be registered.
Zero re-set
Your PEUGEOT dealer or a qualified
workshop carries out this operation
after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-


switch on the ignition.
The display begins a countdown.
When the display shows

"=0", release
the button; the spanner disappears.
Engine oil level indicator
Depending on your vehicle's engine,
when the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information. Oil level correct
Low oil level
Flashing of "OIL",
linked with the
service warning lamp,
accompanied by an
audible signal and a message in the
screen, indicates a low oil level which
could damage the engine.
If the low oil level is confirmed by a
check using the dipstick, it is essential
that the level is topped up.
Oil level gauge fault
Flashing of "OIL--"
indicates a malfunction
of the engine oil level
indicator. Contact
a PEUGEOT dealer or a qualified
workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 30 minutes. Dipstick
A = maximum, never exceed
this level as a surplus of oil
may damage the engine.
Contact a PEUGEOT dealer
or a qualified workshop
without delay.
B = minimum, top up the level
via the oil filler cap, using the
grade of oil suited to your
engine.
With the lighting on,
press the button to vary
the brightness of the
instruments and controls.
When the lighting
reaches the minimum
(or

maximum) setting, release the
button then press it again to increase
(or reduce) the brightness.
As soon as the lighting is of the
required brightness, release the button.
With the ignition on,
press the button until the
zeros
appear.
Lighting dimmer
Instruments and controls

47
Partner-2-VU_en_Chap03_Pret-a-partir_ed02-2014
STOP & START
The Stop & Start system puts the
engine temporarily on standby - ST OP
mode - during stops in the traffic (red
lights, traffic jams, or other...). The
engine restarts automatically - START
mode - as soon as you want to move
off. The restart takes place instantly,
quickly and silently.
Perfect for urban use, the Stop & Start
system reduces fuel consumption and
exhaust emissions as well as the noise
level when stationary.
Operation
Going into engine STOP mode
The "ECO" warning lamp
comes on in the instrument
panel and the engine goes into
standby:
-

with a manual gearbox
, at speeds
below 12 mph (20 km/h), when you
put the gear lever into neutral and
release the clutch pedal,
-

with the 6-speed electronic gear
control gearbox

, at a speed below
5 mph (8 km/h), when you press
the brake pedal or put the gear
lever into position N. If your vehicle is fitted with the system,
a time counter calculates the sum of
the periods in STOP mode during a
journey. It rests itself to zero every time
the ignition is switched on with the key.
With the automatic gearbox
system, for your comfort during
parking manoeuvres, STOP mode
is not available for a few seconds after
coming out of reverse gear.
STOP mode does not affect the
functionality of the vehicle, such as
braking, power steering, for example.
Never refuel with the engine in
STOP mode; you must switch off
the ignition with the key. Special cases: STOP mode
unavailable
STOP mode is not invoked when:
-

the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded
6

mph (10 km/h) since the last
engine start using the key,
-
the engine is needed to maintain
a comfortable temperature in the
passenger compartment,
-

demisting is on,
-

some special conditions (battery
charge, engine temperature,
braking assistance, ambient
temperature...) where the engine
is needed to assure control of a
system.
In this case, the
"ECO"
warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
READY TO SET OFF
3
Stop & Start