wheel Peugeot Partner Tepee 2015 Service Manual

178
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
Without lifting (4 wheels on
the road)
You should always use a towing bar.
BEING TOWED
ths procedure involves the use of the
towing eye supplied with the tools for
changing a wheel.
From the front
- unclip the cover by pressing the
bottom part.
-

Fully screw in the removable towing
eye.
From the rear
- unclip the cover using a coin or the
flat part of the towing eye,
-

Fully screw in the removable towing
eye. When towing with the engine
switched of

f, there is no braking or
steering assistance.
Lifting (only 2 wheels on
the road)
It is preferable to raise the vehicle
using professional lifting equipment.
Vehicles fitted with a manual
gearbox (Diesel version)
In the case of vehicles fitted with
a manual gearbox, the gear lever
must be in neutral, failure to observe
this special condition may result in
damage to transmission and braking
components and the absence of
braking assistance when the engine is
started again.
Chapter 9, "Changing a wheel"
section.
Having your vehicle towed

181
Partner_2_VP_en_Chap09_Caract-technique_ed02-2014
DIMENSIONS (MM)
L Overall length4380
H Overall height 1801-1862
A Wheelbase 2728
B Front overhang 925
C Rear overhang 727
D Width over panels: without mirrors
1810
with mirrors 2112
eWidth of front tracks 1505-1507
F Width of rear tracks 1554-1556
- Length of the loading surface to
the

seat Row 2
990
Row 2, seat fully folded 1343
With front passenger seat folded 3000
Dimensions
teCHNICAL DAtA
9

188
Partner_2_VP_en_Chap09_Caract-technique_ed02-2014
IDENTIFICATION MARKINGS
A. Manufacturer's plate.C. Tyres and paint colour code.
t

he label C, on the front door gives:
-

the wheel and tyre sizes,
-


the brands of tyres recommended
by the manufacturer

,
-

the tyre pressures (the tyre
pressures must be checked when
the tyres are cold, at least once
a

month),
-

the paint colour code.
B. Serial number

.
t

his is engraved on the front right
wheelarch.
Identification markings

07
10.36
Partner_2_VP_en_Chap10b_RT6-2-8_ed02-2014
By alphabetical list
Press RADIO, select the station of your
choice and confirm.
By automatic frequency search
Press 7 or 8 for the automatic search
for a lower or higher radio frequency.
Or turn the thumb wheel at the steering
mounted controls.
By manual frequency search
Press 5 or 6 to adjust the radio
frequency step by step.
Selecting a station
the external environment (hill, building, tunnel, underground car park..\
.) may interfere with the reception, including in RDS station tracking mode. this phenomenon is a normal result of the way in which radio waves are transm\
itted and does not in any way indicate a fault with the audio system.
t

he quality of reception is represented by the number of
active waves in this symbol.
Press RADIO or OK to display the
contextual menu.
Changing waveband
Select "Change waveband".
Select "AM / FM" and confirm.
RADIO

07
10.37
Partner_2_VP_en_Chap10b_RT6-2-8_ed02-2014
Press the button on the numerical keypad to recall a
preset station.
Or press then turn the thumb wheel at the steering
mounted controls.
Presetting a station
After selecting a station, press one of the buttons
on the numerical keypad for 2 seconds to preset the
current station.
An audible signal confirms that the station has been preset.
Press RADIO.
Activate / Deactivate RDS
RDS, if activated, allows you to continue listening to the same station
by automatic retuning to alternative frequencies. However, in certain
conditions, coverage of an RDS station may not be assured throughout
the entire country as radio stations do not cover 100 % of the territory\
.
t
his explains the loss of reception of the station during a journey.
Select "Guidance options " then
confirm.
Activate or deactivate "RDS" then
confirm.
RADIO

06
10.70
Partner_2_VP_en_Chap10c_RD45_ed02_2014
Receiving a callAn incoming call is announced by a ring and a superimposed
display in the vehicle's screen.
Select the Y
e S tab on the display
using the buttons and confirm by
pressing OK.
Press this button to accept the call. Making a call
From the Bluetooth telephone function Audio menu, select Manage
the telephone call then Call, Call list or Directory.
Press this button for more than two seconds for
access to your directory, then navigate with the
thumb wheel.
Or
to dial a number

, use your telephone's keypad,
with the vehicle stationary.
BLUETOOTH
the system accesses the telephone's contacts directory, depending
on compatibility , and while the Bluetooth connection with it is
maintained.
With certain telephones connected by Bluetooth you can send a
contact to the directory of the audio system.
Contacts imported in this way are saved in a permanent directory
visible to all, whatever the telephone connected.
t

he menu for the directory is not accessible if it is empty.