key battery Peugeot Partner Tepee 2015 Owner's Manual

5
Partner_2_VP_en_Chap01_vue-ensemble_ed02-2014
EXTERIOR
Remote control 18-19
Changing the battery ,
reinitialisation

19
Key


18
Starting

50
Hill start assist

51
Central locking /


unlocking

18, 27
Filler cap, fuel tank


147-148
Fuel cut-of

f, Diesel priming
148
AdBlue additive,


topping up

149-153, 154-156
Wiper blades


177
Door mirrors


103
Side repeaters


170
Front lamps, foglamps, direction indicators


52-54, 169-170
Headlamp beam height adjustment


54
Changing front bulbs


168-170
Headlamp wash


56, 144
Snow cover


166
Front doors


21
Sliding side


doors

22-23
Key


18
Opening the bonnet


140
Child lock


134
towing, lifting


178
T

owbar

135-136
Parking sesnsors


107-108
Rear roof flap


26e

mergency control

23
Spare wheel, jack,


changing a wheel,
tools

160-165temporary puncture repair kit


159
Inflation, pressures


188
Zenith roof


90-91
Roof bars


94, 95
Rear lamps, direction


indicators

52-53, 171-172
3rd brake lamp


172
Changing rear bulbs


168, 171-172
Doors, tailgate


23-25
Accessories


137-138
Number plate lamps


172 Dimensions


180-183
Brakes, pads

106, 143, 145e

mergency braking

109
ABS,

e
BFD

109
ASR, DSC


1

10
"
g
rip control"

1

11-112
tyres, pressures


188
Snow chains


167
T

yre under-inflation detection

3

9-40
1
OVeRVIeW
Location

19
Partner_2_VP_en_Chap03_Pret-a-partir_ed02-2014
Good practice
take care not to allow the remote
control to come into contact with
grease, dust, rain or a damp
environment.
A
heavy object attached to the key
(keyring, ...) weighing on the shaft of
the key in the switch, may cause a
malfunction.
REMOTE CONTROL Reinitialising the remote control
Following changing of the remote
control battery or disconnection of the
vehicle battery, the remote control may
have to be reinitialised.
Wait at least one minute before using
the remote control.
Insert the key in the ignition switch with
the buttons (padlocks) of the remote
control facing you.
Switch on the ignition.
Press the locking padlock for at
least five seconds within the next
ten
seconds.
Switch off the ignition.
Wait at least one minute before using
the remote control.
t

he remote control is now working
again.u
se only identical batteries or
batteries of an equivalent type to those
recommended by P
euge
O
t
dealers.
Do not discard the remote control
batteries, they contain metals which
are harmful to the environment.
Deposit them at a P

euge
O
t

dealership, or at an authorised
collection point.
Folding / unfolding the key
Changing the battery
Battery ref.: CR1620 / 3 volts.
The "battery flat" information is given
by an audible signal, accompanied by
a message in the screen.
to replace the battery

, unclip the
casing using a coin at the ring.
If the remote control does not work
after the battery has been changed,
reinitialise the remote control.
t

here is a risk of damage if the
replacement battery is not the correct
type. Press this button to release
the key from its housing.
to fold the key

, press this
chromed button then fold
the key into the housing.
If you do not press the button, the
mechanism may be damaged.
Access
ReADY tO Set OFF
3

23
Partner_2_VP_en_Chap03_Pret-a-partir_ed02-2014
Operation in the event of a
battery failure
Front and side passenger doors
In the event of a battery or of the
central locking fault, use the lock to
lock the doors mechanically.
- t
o open the door and get out of the
vehicle, pull the interior control.
-

t
o lock the door
, insert the key in
the lock, located on the edge of the
door, then turn it one eighth of a
turn.
Driver's door
-

Insert the key in the lock, then turn
it to the right to lock or to the left to
unlock.
TAILGATE From inside
Emergency control
In the event of a central unlocking
operating fault, this permits unlocking
of the tailgate from the inside.
Insert a small screwdriver in the
opening, between the tailgate and the
floor. To unlock the lock, move the
catch to the left then push the tailgate.
From outside
Locking/unlocking is by means of the
remote control.
to open, press the control below the
trim then raise the tailgate.
A

pull strap is available to close the
tailgate in the high position.
g

uide the closing of the tailgate to the
balance point of its travel then apply
a final press on the tailgate to close it
fully.
Access
ReADY tO Set OFF
3

47
Partner_2_VP_en_Chap03_Pret-a-partir_ed02-2014
STOP & START
the Stop & Start system puts the
engine temporarily on standby - S tOP
mode - during stops in the traffic (red
lights, traffic jams, or other...). The
engine restarts automatically - S
t
ARt
mode - as soon as you want to move
of

f.
t
he restart takes place instantly,
quickly and silently.
Perfect for urban use, the Stop & Start
system reduces fuel consumption and
exhaust emissions as well as the noise
level when stationary.
Operation
Going into engine STOP mode
the "ECO" warning lamp comes
on in the instrument panel and
the engine goes into standby:
- with a manual gearbox , at speeds
below 12 mph (20 km/h), when you
put the gear lever into neutral and
release the clutch pedal,
-

with the 6-speed electronic gear
control gearbox

, at a speed below
5 mph (8 km/h), when you press
the brake pedal or put the gear
lever into position N. If your vehicle is fitted with the system,
a time counter calculates the sum of
the periods in S
t
OP
mode during a
journey. It rests itself to zero every time
the ignition is switched on with the key.
With the automatic gearbox
system, for your comfort during
parking manoeuvres, S t
OP
mode
is not available for a few seconds after
coming out of reverse gear.
S t
OP
mode does not affect the
functionality of the vehicle, such as
braking, power steering, for example.
Never refuel with the engine in
S t
OP
mode; you must switch off
the ignition with the key. Special cases: STOP mode
unavailable
S t
OP
mode is not invoked when:
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded
6

mph (10 km/h) since the last
engine start using the key,
-
the engine is needed to maintain
a comfortable temperature in the
passenger compartment,
-

demisting is on,
-

some special conditions (battery
charge, engine temperature,
braking assistance, ambient
temperature...) where the engine
is needed to assure control of a
system.
In this case, the
"ECO"
warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
Stop & Start
ReADY tO Set OFF
3

49
Partner_2_VP_en_Chap03_Pret-a-partir_ed02-2014
Reactivation
Press the "ECO OFF" switch again.
t
he system is active again; this is
confirmed by the switch warning
lamp going off and a message in the
instrument panel.
t

he system is reactivated
automatically at every new start
using the key.
Operating fault
In the event of a malfunction
with the system, the "ECO
OFF" switch warning lamp
flashes, then comes on
continuously.
Maintenance
Before working under the bonnet,
deactivate the Stop & Start system
to avoid any risk of injury resulting
from automatic operation of S
t
ARt
mode.
This system requires a specific
battery with a special specification
and technology (reference numbers
available from a P

euge O t
dealer or a
qualified workshop).
Fitting a battery not listed by
P

euge O t introduces the risk of
malfunction of the system.
t

he Stop & Start system makes
use of advanced technology. All
work on this type of battery must
be done only by a P
euge O t
dealer or
a qualified workshop.
have it checked by a P

euge
O
t
dealer
or a qualified workshop.
In the event of a fault in S

t
OP

mode,
the vehicle may stall. All of the warning
lamps in the instrument panel come
on. It is then necessary to switch off
the ignition and start the engine again
using the key.
Stop & Start
ReADY tO Set OFF
3

158
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
ECONOMY MODE
After the engine has stopped, with
the key in the ignition position, certain
functions (windscreen wiper, electric
windows, courtesy lamps, audio
equipment, etc.) can only be used for a
cumulative duration of thirty minutes, to
prevent discharging of the battery.
Once the thirty minutes are over, the
active functions are put on standby
and the battery warning lamp flashes
accompanied by a message in the
screen.
to resume the use of these functions
immediately

, start the engine and let it
run for a few minutes.
t

he time available will then be double
the time for which the engine was left
running. However, this time will always
be between five and thirty minutes.
A flat battery will prevent the
engine from starting.
Battery