fold seats Peugeot Partner Tepee 2017 Owner's Manual

78
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
Never drive with the head
restraints removed; they must be
in place and correctly adjusted.
Adjustable armrestFront heated seats control
Each front seat may be fitted with a
control located on the side part of the
cushion.
Press to switch on the cushion heating.
Press again to switch it off.
Head restraint height
To raise the head restraint, slide it vertically
upwards.
To lower the head restraint, press the
button and slide the head restraint vertically
downwards.
The adjustment is correct when the upper
edge of the head restraint is level with the
top of the head.
To remove the head restraint, press the
button and pull the head restraint upwards.
To re-install the head restraint, engage
the rods in the holes making sure they are
aligned with the seat back.
To access the vertical position, raise
the armrest until it locks.
Lower the armrest to return it to a
position for use.
To remove the armrest, press the
release button from the vertical position
and move aside the armrest.
To put the armrest back in place, clip it
in the vertical position.
If the vehicle is fitted with the additional
console and an armrest, to fold the
passenger seat to the table position
remove the console or the armrest.
Seats

79
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
REAR BENCH SEAT
Each 1/3 - 2/3 section can be fully
folded, then removed individually.
Head restraint
The 1/3 - 2/3 split rear bench seat is fitted
with "comma" shape head restraints.
High position: lift and raise the head
restraint.
Low position: press on the head
restraint to lower it.
To remove the head restraint, after
raising it press the tab and lift the head
restraint.
To install the head restraint, engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
EASE OF USE and COMFORT
4
Seats

80
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
Fully folded position
Example of operations for the
1/3 section. They are identical for the
2/3
section. -

Raise the grey control bar
, located
at the rear of the seat cushion.
-
T
ilt the entire seat forward.
Putting back in place
Check that the seat is locked
on the floor securely when it is
returned to the sitting position.
-

Place the head restraints in the low
position.
-


If necessary

, move the front seats
forward.
-
Press the grey control located on
the upper part of the seat backrest.
-

Fold the seat backrest onto the
seat cushion. T

ilt the entire seat rearwards until it
locks into place.
Raise the seat backrest.
The seat is locked correctly when the
control (at the top of the seat back) is
no longer visible.
Seats

81
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
Removing the bench seatRefitting the bench seat
Refer to the "Fully folded position",
described previously. To return the bench seat
(1/3
section and/or 2/3 section) to
the "passenger carrying" position,
refer to the "Fully folded position"
described previously.
-

T
ilt the entire seat rearwards by
approximately 45°.
-
Lift the bench seat
vertically to the
limit of the anchorages.
-
Straighten bench seat by tilting it
forwards then lift it.
-


If necessary
, move the front seats
forward.
-

Place the bench seat (1/3 section and/or
2/3 section) in the fully folded position.
- Offer up the bench seat (1/3 section
and/or 2/3 section) vertically.
-

Place the hooks between the two
bars.
-


Fold the bench seat rearwards.
EASE OF USE and COMFORT
4
Seats

82
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
REAR SEATS (5 SEAT VERSION)Head restraint
Each seat can be removed individually.
Each time a seat is returned to the
sitting position or after removing then
refitting a seat, check that it is locked
on the floor securely.
The three independent rear seats
are fitted with "comma" shape head
restraints.
The back of the centre seat, folded
onto the seat cushion, has a shell
which serves as a table with cup
holder. High position: lift and raise the head
restraint.
Low position: press on the head
restraint to lower it.
To remove the head restraint, after
raising it press the tab and lift the head
restraint.
To install the head restraint, engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
Seats

83
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
Adjusting the angle of the seat backrest
Placing the seat back in the
table position
Returning the seat back to the sitting position
Placing the seat in the fully
folded position
Returning the seat to its original position
- Operate the control and adjust the
angle of the seat backrest.
-

Pull the control to fold the seat back
onto the seat cushion.
Do not place hard or heavy objects
on the table.

They could become
dangerous projectiles in the event of
sharp braking or impact. -

Release the seat back by pullin
g
the control, then return it to its
original position.
When returning the seat backrest to
the sitting position, ensure that it is
locked securely.
-

Pull the control to place the seat
back in the table position.
-


Raise the bar located behind the
seat to release the rear anchoring
points.
-


T
ilt the entire seat forwards, until it
locks. -
Push the red control.
-

Fold back the seat to fix the rear
anchoring points.
-


Raise the seat backrest by pullin
g
the control.
-

Check that the seat has correctly
locked into place.Before unfolding the seat, check
that no object is obstructing the
anchorage points or preventing
correct locking of the seats.
EASE OF USE and COMFORT
4
Seats

84
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
Removing the seat
- If necessary, move the front
seats forward and lower the head
restraint.
-

Place the seat in the fully folded
position.
Good practice
Following the various operations:
-
do not remove a head restraint
without storing it and fix it to a
support,
-


ensure that the passengers can
always access the seat belts and
fasten them easily

,
-

passengers must never take
their seat without adjusting and
fastening their seat belt.
Refer to the "Fully folded position"
described previously

.
-

Press the red lever to release the
front feet.
-


T

ilt the entire seat rearwards by
approximately 45° without releasing
the lever.
-

Release the lever

.
-

Lift the seat

vertically to the limit of
the anchorages.
-

Straighten the seat by tilting it
forwards then lift it.
Refitting the seat
- Tilt the seat forward by 45°.
-
Place the hooks between the
two

bars.
-

Fold back the seat to fix the rear
anchoring points.
-


Pull the control to return the seat
back to its initial position.
-


Raise the head restraint. Before unfolding the seat, check
that no object is obstructing the
anchorage points or preventing
correct locking of the seats.
Seats

87
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
Adjusting the angle of the seat backrest
- Operate the control and adjust the
angle.
Placing the seat backrest in the
table position
-

Lower the head restraint fully
.
-

Operate the control to fold the seat
back onto the seat cushion. Returning the seat backrest to the
sitting position
-


Release the seat backrest by
pullin

g the control, then return it to
its original position.
-
Ensure that it has correctly locked
into place.
Placing the seat in the fully folded
position
-

Place the seat in the table position.
-


Pull the red strap, located behind
the seat, to release the feet of the
seat from their anchorage on the
floor

.
-

T
ilt the entire seat forwards.
Row 2 seat adjustmentsReturning the seat to its original
position
-
Unfold the entire seat.
Before folding the seat, ensure
that:
-


in row 3, no passenger's
foot is at one of the seat
anchorages on the floor

,
-

the seat is locked securely on
the floor

,
-

the seat belt is available for
the passenger

.
EASE OF USE and COMFORT
4
Seats

88
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
Row 3 seat adjustments
Placing the seat backrest in the
table position
-
Lower the head restraint fully
.
-

Operate the control to fold the seat
backrest onto the seat cushion.
Returning the seat backrest to the
sitting position
-


Release the seat backrest by
pullin

g the control, then return it to
its original position.
-

Check that it has correctly locked in
place. Returning the seat to its original
position
-


Push the red control.
-


Unfold the entire seat.
Placing the seat in the fully folded
position
-


Place the seat in the table position.
-


Raise the bar fitted with a red
strap, located behind the seat, to
release feet of the seat from their
anchorage on the floor

.
-

T
ilt the entire seat forwards.Ensure that:
-

the seat is locked securely on
the floor

,
-

the seat belt is available for
the passenger

.
Seats

89
Partner2VP_en_Chap04_Ergonomie_ed02-2016Partner2VP_en_Chap04_Ergonomie_ed02-2016
Entering, exiting from Row 3
Entering
-
Place the row 2 seat in the table
position.
Exiting
-


Lower the head restraint fully
.
-

Operate the yellow control, located
on the back of the row 2 seat
backrest.
-


Fold the seat backrest to the table
position. Ensure that the centre seat belt is
stowed correctly in its housing in
the headlining.
-


T
ilt it to the fully folded position to
allow access. -

Pull the red strap to place the seat
in the fully folded position.
-
T ilt the entire seat forwards.
-
Exit via the side door
.
Before folding it back, ensure that
the feet of the passenger in row 3
are not obstructing the row 2 seat
anchoring points.
EASE OF USE and COMFORT
4
Seats