wheel Peugeot RCZ 2012.5 - RHD (UK, Australia) Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2012.5, Model line: RCZ, Model: Peugeot RCZ 2012.5Pages: 336, PDF Size: 14.1 MB
Page 165 of 336
8/
PRACTICAL INFORMATION
CHANGING A WHEEL
Parking the vehicle
Immobilise the vehicle where it does not block traffi c: the ground
must be level, stable and non-slippery ground.
Apply the parking brake, switch off the ignition and engage fi rst
gear (position P
for the automatic gearbox) to lock the wheels.
It is imperative that you ensure that the occupants get out of the
vehicle and wait where they are safe.
If necessary, place a chock under the wheel diagonally opposite
the wheel to be changed.
Never go underneath a vehicle raised using a jack; use an axle
stand.
Security socket: for adaptation of the
wheelbrace to the special "security" bolts.
Specifi c to your vehicle, it is stored in the
glove box.
Wheelbrace: for removal of the wheel fi xing
bolts.
Jack with integrated handle: for lifting the
vehicle.
TOOLS REQUIRED *
Bolt cover removal tool: for removal of the
bolt fi nishers (covers) on alloy wheels.
*
Depending on the country of sale, the vehicle may be equipped with
the tools needed to change a wheel and a spare wheel (see following
pages).
Page 166 of 336
164
REMOVING THE WHEEL
)
Place the jack in contact with one of the two front A
or rear B
locations provided on the underbody, whichever is closest to the
wheel to be changed.
)
Raise the vehicle until there is suffi cient space between the wheel
and the ground to admit the spare (not punctured) wheel easily.
)
Remove the bolts and store them in a clean place.
)
Remove the wheel.
)
Remove the cover on each of the bolts using the bolt cover removal
tool.
)
Fit the security socket on the wheelbrace to slacken the security
bolt.
)
Slacken the other bolts using the wheelbrace only.
)
Extend the jack until its base plate is in contact with the ground.
Ensure that the centreline of the jack base plate is directly below
the location A
or B
used.
Page 167 of 336
8/
PRACTICAL INFORMATION
FITTING THE WHEEL
)
Put the wheel in place on the hub.
)
Screw in the bolts by hand.
)
Pre-tighten the security bolt using the wheelbrace fi tted with the
security socket.
)
Pre-tighten the other bolts using the wheelbrace only.
)
Lower the vehicle fully.
)
Fold the jack and detach it.
)
Tighten the security bolt using the wheelbrace fi tted with the
security socket.
)
Tighten the other bolts using the wheelbrace only.
)
Refi t the covers on each of the bolts.
)
Store the tools in the storage box.
After changing a wheel
Have the tightening of the bolts and the pressure of the new wheel
checked by a PEUGEOT dealer or a qualifi ed workshop without
delay.
Page 168 of 336
166
TOOLS AND SPARE WHEEL *
Depending on the country of sale, the vehicle is equipped with the tools
needed to change a wheel and may also be equipped with a spare
wheel.
The spare wheel is stowed in a protective cover, secured to the boot
fl oor with Velcro
®.
The tools are held in a storage box under the boot fl oor.
Never drive with the rear seat folded when the
spare wheel - or a punctured wheel - is present
in the boot.
Warning marking
"Do not release the backrest of the rear seats!"
*
According to country.
Access to the spare wheel *
)
Open the boot lid.
)
Remove the spare wheel by grasping the grip of its protective
cover.
)
Position the wheel vertically so as to read the warning markings.
)
Remove the Velcro
® located on the tyre tread.
)
Detach the straps, located on each sidewall, then slacken them.
)
Remove the wheel from its protective cover.
When refi tting the wheel into its cover, place it so that the valve is
opposite the strap fi xings.
Page 170 of 336
168
In wintry conditions, snow chains improve traction as well as the
behaviour of the vehicle when braking.
Use only the chains designed to be fi tted to the type of wheel fi tted to
your vehicle:
Original tyre size Maximum link size.
235/45 R18
not chainable
235/40 R19
For more information on snow chains, contact a PEUGEOT dealer or a
qualifi ed workshop.
The snow chains must be fi tted only to the front wheels. They
must never be fi tted to "space-saver" type spare wheels.
Take account of the legislation in force in your country on the use
of snow chains and the maximum running speed authorised.
Avoid driving on roads that have been cleared of snow, to
avoid damaging your vehicle's tyres and the road surface. It is
recommended that before you leave, you practise fi tting the snow
chains on a level and dry surface. If your vehicle is fi tted with alloy
wheels, check that no part of the chain or its fi xings is in contact
with the wheel rim.
Original tyre size Maximum link size.
225/45 R18 9 mm
Advice on installation
)
If you have to fi t the chains during a journey, stop the vehicle on a
fl at surface on the side of the road.
)
Apply the parking brake and position any wheel chocks to prevent
movement of your vehicle.
)
Fit the chains following the instructions provided by the
manufacturer.
)
Move off gently and drive for a few moments, without exceeding
30 mph (50 km/h).
)
Stop your vehicle and check that the snow chains are correctly
tightened.
Page 186 of 336
184
ENGINE COMPARTMENT FUSES
The fusebox is placed in the engine compartment near the battery (left-
hand side).
Access to the fuses
)
Unclip the cover.
)
Change the fuse (see corresponding paragraph).
)
When you have fi nished, close the cover carefully to assure the
sealing of the fusebox.
Fuse table
Fuse N°
Rating
Functions
F1
20 A
Engine control unit supply, injection
pump and EGR electrovalves (Diesel),
injectors (Diesel).
F2
15 A
Horn.
F3
10 A
Front wash-wipe.
F4
20 A
Daytime running lamps.
F5
15 A
Air fl ow sensor, coolant pump, oil pump,
thermostat, blow-by heater (petrol),
by-pass and EGR electrovalves (Diesel),
diesel heater (Diesel).
F6
10 A
Steering wheel angle sensor, ABS/ESC
control unit, ESC sensor.
F7
10 A
Power steering control unit, automatic
gearbox, engine coolant level detector,
dual function brake switch.
F8
25 A
Starter motor control.
F9
10 A
Diagnostic socket, directional
headlamps, particle emission fi lter pump
(Diesel).
F10
30 A
Engine control unit actuators (petrol:
ignition coils, electrovalves, injectors,
fuel pump (Diesel: electrovalves,
heaters).
F11
40 A
Air conditioning blower.
Page 189 of 336
8/
PRACTICAL INFORMATION
TOWING A VEHICLE
TOWING EYE
This is stored in the boot under the fl oor.
For access to it:
)
open the boot,
)
raise the fl oor using the strap,
)
secure it in the vertical position beyond the stops, located on the
sides of the boot,
)
remove the towing eye from the storage box.
GENERAL RECOMMENDATIONS
Observe the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of
the towed vehicle.
The person at the wheel of the towed vehicle must have a valid
driving licence.
When towing a vehicle with all four wheels on the ground, always
use an approved towing bar; rope and straps are prohibited.
When towing a vehicle with the engine off, there is no longer any
power assistance for braking or steering.
In the following cases, you must always call on a professional
recovery service:
- vehicle broken down on a motorway or fast road,
- 4 wheel drive vehicle,
- when it is not possible to put the gearbox into neutral, unlock
the steering, or release the parking brake,
- towing with only two wheels on the ground,
- where there is no approved towing bar available...
Page 194 of 336
192
MATT PAINT
If you vehicle is fi nished with a clear matt lacquer, please observe the
following recommendations to avoid damaging the paintwork by the use
of an inappropriate cleaning procedures.
These recommendations are also valid for alloy road wheels fi nished
with clear matt lacquer.
Never clean the vehicle without water.
Never wash your vehicle in an automatic roller brush car wash.
Never polish the vehicle body, nor the alloy wheels. Doing this will
make the paintwork shiny.
Do not use paint cleaners, abrasive products or paint polishing or
preserving products (such as wax, for example) on the paintwork.
These products are only suitable for bright fi nishes. Application of
these products on vehicles with a matt fi nish will seriously damage
the paint surface of the vehicle, giving rise to irreversible shiny or
stained areas.
Never use a high pressure jet wash with a lance fi tted with a
brush, this may scratch the paintwork.
Never select a wash programme that fi nishes with a hot wax
cycle. From the range of cleaning and maintenance products in the
"TECHNATURE" range recommended and approved by PEUGEOT,
use only the insect remover and car shampoo, which are the only
products to be used on the bodywork.
The insect remover can also be used to remove minor marks (for
example: fi nger marks...).
Always have paint repairs done by a PEUGEOT dealer or a qualifi ed
workshop.
We recommend the use of a high pressure jet wash, or at least a
water hose with a high output.
We recommend that the vehicle be rinsed using de-ionised water.
Use only a microfi bre cloth to dry the vehicle. It must be clean and
used without heavy pressure.
Lightly wipe off any fuel stains present on the bodywork using a
soft cloth, then leave to dry.
Page 195 of 336
8/
PRACTICAL INFORMATION
ACCESSORIES
A wide range of accessories and genuine parts is available from the
PEUGEOT dealer network.
These accessories and parts have been tested and approved for
reliability and safety.
They are all adapted to your vehicle and benefi t from PEUGEOT's
recommendation and warranty.
"Comfort":
front parking sensors, cool box...
"Transport solutions":
boot tray, boot spacers, towbar bicycle carrier, towbar with quickly
detachable ball, towbar harnesses...
"Style":
leather and alcantara sport steering wheel, alcantara gear lever gaiter,
alloy wheels, door mirror shells in carbon fi bre...
"Safety and security":
anti-theft alarm, window etching, wheel security bolts, breathalyser, fi rst
aid kit, fi re extinguisher, warning triangle, high visibility jacket, booster
cushions and child seats, stolen vehicle tracking system, snow chains,
anti-skid tyre covers...
"Protection":
boot liner, mats * , bumper protective strips, vehicle protective cover...
*
To avoid any risk of jamming of the pedals:
- ensure that the mat is positioned and secured correctly,
- never fi t one mat on top of another.
When fi tting a trailer towbar and its harness outside the
PEUGEOT dealer network, this must be done following the
manufacturer's recommendations.
Page 202 of 336
200
IDENTIFICAT ION MARKINGS
Various visible markings for the identifi cation of your vehicle.
A.
Vehicle identifi cation number (VIN) under the bonnet.
This number is engraved on the bodywork near the damper
support.
For access to it, raise the plastic cover.
C.
Manufacturer's label.
The number is indicated on a self-destroying label affi xed to the
door aperture, below the door striker, on the right-hand side.
This label also indicates the unladen weight, the gross vehicle
weight (GVW) and the gross train weight (GVW).
For information concerning the possibilities for installing snow
chains, contact a PEUGEOT dealer or a qualifi ed workshop.
The tyre pressures must be checked when the tyres are cold, at
least once a month.
If the tyre pressures are too low, this increases fuel consumption.
B.
VIN on the windscreen lower crossmember.
This number is indicated on a self-adhesive label which is visible
through the windscreen.
D.
Tyre/paint label.
This label is affi xed to the door aperture, on the driver's side.
It bears the following information:
- the tyre infl ation pressures, laden and unladen,
- the wheel rim and tyre sizes,
- the brands of tyre recommended by the manufacturer,
- the infl ation pressure of the spare wheel,
- the paint colour code.