brake PEUGEOT RCZ 2012 User Guide

132
"PORSCHE TIPTRONIC SYSTEM"
AUTOMATIC GEARBOX

GEAR SELECTION GATE



1.
Gear lever.

2.
Button "S"
(sport)
.

3.
Button " 7
" (snow)
.



GEAR LEVER POSITIONS


P.
Park.


- Immobilisation of the vehicle, parking brake on or off.

- Starting the engine.

R.
Reverse.


- Reversing manoeuvres, vehicle stationary, engine at idle.

N.
Neutral.


- Immobilisation of the vehicle, parking brake on.

- Starting the engine.

D.
Automatic operation.

M. + / -
Manual operation with sequential changing of the six gears.


)
Press forwards to change up through the gears.
or


)
Press rearwards to change down through the gears.
Six speed automatic gearbox which offers a choice between the comfort
of fully automatic operation, enhanced by sport and snow programmes,
or manual gear changing.
For this, four driving modes are offered:


- automatic
operation for electronic management of the gears by the
gearbox,

- sport
programme for a more dynamic style of driving,

- snow
programme to improve driving when traction is poor,

- manual
operation for sequential changing of the gears by the
driver.

6/
33
33
DRIVING

DISPLAYS IN THE INSTRUMENT PANEL

When you move the lever in the gate to select a position, the
corresponding symbol is displayed in the instrument panel.

P.
Park

R.
Reverse

N.
Neutral

D1... D6.
Drive (Automatic driving)

S.
Sport
programme

7
. Snow
programme

M1... M6.
Manual (Sequential driving)

-.
Invalid value during manual operation


MOVING OFF



)
Apply the parking brake.

)
Select position P
or N
.

)
Start the engine.
If this procedure is not followed, there is an audible signal, accompanied
by a message in the screen.


)
With the engine running, press the brake pedal.

)
Release the parking brake.

)
Select position R
, D
or M
.

)
Gradually release the brake pedal.
The vehicle moves off immediately.
If position N
is engaged inadvertently while driving, allow the
engine to return to idle then engage position D
to accelerate.
When the engine is running at idle, with the brakes released, if
position R
, D
or M
is selected, the vehicle moves even without the
accelerator being pressed.
When the engine is running, never leave children in the vehicle
without supervision.
When carrying out maintenance with the engine running, apply the
parking brake and select position P
.
A message appears if you try to move the gear lever from
position P
to another position without pressing the brake pedal.

6/
DRIVING
It is only possible to change from one gear to another if the vehicle
speed and engine speed permit; otherwise, the gearbox will operate
temporarily in automatic mode.

M
and the gears engaged manually appear in succession in
the instrument panel.
If the engine speed is too low or too high, the gear selected
fl ashes for a few seconds, then the actual gear engaged is
displayed.
It is possible to change from position D
(automatic) to position M

(manual) at any time.
When the vehicle is stationary or moving very slowly, the gearbox
selects gear M1
automatically.
The sport and snow programmes do not operate in manual mode.


Invalid value during manual operation

This symbol is displayed if a gear is not engaged correctly
(selector between two positions).



STOPPING THE VEHICLE

Before switching off the engine, you can engage position P
or N
to
place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle. If the lever is not in position P
, when the driver's door is opened or
approximately 45 seconds after the ignition is switched off, there is
an audible signal is heard accompanied by a message.


)
Return the lever to position P
; the audible signal stops and the
message disappears.



OPERATING FAULT

When the ignition is on, the illumination of this warning lamp,
accompanied by an audible signal and a message in the
screen, indicates a gearbox malfunction.
In this case, the gearbox switches to emergency mode and is locked in
3rd gear. You may feel a substantial knock when changing from P
to R

and from N
to R
. This will not cause any damage to the gearbox.
Do not exceed a speed of 60 mph (100 km/h), local speed restrictions
permitting.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
This warning lamp may also come on if a door is opened.

There is a risk of damage to the gearbox:


- if you press the accelerator and brake pedals at the same
time,

- if you force the lever from position P
to another position when
the battery is fl at.
To reduce fuel consumption during a long period stationary with
the engine running (traffi c jam, etc.), place the gear lever in
position N
and apply the parking brake.

6/
DRIVING
CRUISE CONTROL
System which automatically maintains the speed of the vehicle at the
value programmed by the driver, without any action on the accelerator
pedal.
The cruise control is switched off
manually or by pressing the brake or
clutch pedal or on triggering of the trajectory control system for safety
reasons.
Switching off the ignition cancels any programmed speed value.


STEERING MOUNTED CONTROL

The functions of this system are grouped together on the steering
mounted control.


1.
Cruise control mode selection dial.

2.
Speed programming / value decrease button.

3.
Speed programming / value increase button.

4.
Cruise control off / resume button.
The cruise control cannot, in any circumstances, replace the need
to respect speed limits, nor can it replace the need for vigilance
and responsibility on the part of the driver.
You are advised to keep your feet near the pedals at all times. The cruise control is switched on
manually: it requires a minimum
vehicle speed of 25 mph (40 km/h) and the engaging:


- of fourth gear on the manual gearbox,

- of second gear on the automatic gearbox, in sequential driving
mode,

- of position D
on the automatic gearbox.
It is possible to exceed the programmed speed temporarily by pressing
the accelerator pedal.
To return to the programmed speed, simply release the accelerator
pedal.

7/
CHECKS
PETROL ENGINES
The various caps and covers allow access for checking the levels of the various fl uids and for replacing certain components.


1.
Power steering reservoir.

2.
Screenwash and headlamp wash reservoir.

3.
Coolant reservoir.

4.
Brake fl uid reservoir.

5.
Battery / Fuses.
6.
Fusebox.

7.
Air fi lter.

8.
Engine oil dipstick.

9.
Engine oil fi ller cap.

150
DIESEL ENGINE
The various caps and covers allow access for checking the levels of the various fl uids, for replacing certain components and for priming the fuel system.


1.
Power steering reservoir.

2.
Screenwash and headlamp wash reservoir.

3.
Coolant reservoir.

4.
Brake fl uid reservoir.

5.
Battery / Fuses.

6.
Fusebox.
7.
Air fi lter.

8.
Engine oil dipstick.

9.
Engine oil fi ller cap.

10.
Priming pump.

11 .
Bleed screw.

152





CHECKING LEVELS



















OIL LEVEL


The check is carried out either when the ignition is switched
on using the oil level indicator in the instrument panel, or using
the dipstick.
It will only be correct if the vehicle is on level ground and the engine
has been off for more than 30 minutes.
Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could start
at any time (even with the ignition off).



If a level drops signifi cantly, have the corresponding system checked by a PEUGEOT dealer or a qualifi ed workshop.
Check all of these levels regularly, in line with the servicing booklet and the requirements of the warranties. Top them up if necessary, unless otherwise indicated.


Engine oil change

Refer to the servicing and warranty booklet for details of the interval
for this operation.
In order to maintain the reliability of the engine and emission control
system, the use of additives in the engine oil is prohibited. It is normal to top up the oil level between two services (or oil
changes). PEUGEOT recommends that you check the level, and
top up if necessary, every 3 000 miles (5 000 kms).
After topping up the oil, the check when switching on the ignition with
the oil level indicator in the instrument panel is not valid during the
30 minutes after topping up.


Oil specification

The oil must be the correct grade for your engine and conform to the
manufacturer's recommendations.












BRAKE FLUID LEVEL

The brake fl uid level should be close to the "MAX" mark.
If it is not, check the brake pad wear.

Changing the fluid

Refer to the servicing and warranty booklet for details of the interval
for this operation.


Fluid specification

The brake fl uid must conform to the manufacturer's recommendations
and meet the DOT3 or DOT4 standard.












POWER STEERING FLUID LEVEL

The power steering fl uid level should be close to the "MAX"
mark. With the engine cold, unscrew the cap to check the level.

7/
CHECKS






MANUAL GEARBOX






AUTOMATIC GEARBOX















BRAKE PADS
BRAKE DISC WEAR

The gearbox does not require any maintenance (no oil change).
Refer to the servicing and warranty booklet for the details of
the level checking interval for this component.
The gearbox does not require any maintenance (no oil change).
Refer to the servicing and warranty booklet for details of the
level checking interval for this component.
Brake wear depends on the style of driving, particularly in
the case of vehicles used in town, over short distances.
It may be necessary to have the condition of the brakes
checked, even between vehicle services.
Unless there is a leak in the circuit, a drop in the brake fl uid level
indicates that the brake pads are worn. For information on checking brake disc wear, contact a
PEUGEOT dealer or a qualifi ed workshop.
















Only use products recommended by PEUGEOT or products of
equivalent quality and specifi cation.
In order to optimise the operation of units as important as the
braking system, PEUGEOT selects and offers very specifi c
products.
To avoid damaging the electrical units, the use of a high pressure
washer in the engine compartment is strictly prohibited
.























PARKING BRAKE


If excessive travel or a loss of effectiveness of this system
is noticed, the parking brake must be checked, even
between two services.

Checking this system must be done by a PEUGEOT dealer
or a qualifi ed workshop.

8/
PRACTICAL INFORMATION
CHANGING A WHEEL


Parking the vehicle

Immobilise the vehicle where it does not block traffi c: the ground
must be level, stable and non-slippery ground.
Apply the parking brake, switch off the ignition and engage fi rst
gear (position P
for the automatic gearbox) to lock the wheels.
It is imperative that you ensure that the occupants get out of the
vehicle and wait where they are safe.
If necessary, place a chock under the wheel diagonally opposite
the wheel to be changed.
Never go underneath a vehicle raised using a jack; use an axle
stand.
Security socket: for adaptation of the
wheelbrace to the special "security" bolts.
Specifi c to your vehicle, it is stored in the
glove box.
Wheelbrace: for removal of the wheel fi xing
bolts.
Jack with integrated handle: for lifting the
vehicle.

TOOLS REQUIRED *

Bolt cover removal tool: for removal of the
bolt fi nishers (covers) on alloy wheels.

*
Depending on the country of sale, the vehicle may be equipped with
the tools needed to change a wheel and a spare wheel (see following
pages).

168

In wintry conditions, snow chains improve traction as well as the
behaviour of the vehicle when braking.

Use only the chains designed to be fi tted to the type of wheel fi tted to
your vehicle:
Original tyre size Maximum link size.
235/45 R18
not chainable
235/40 R19
For more information on snow chains, contact a PEUGEOT dealer or a
qualifi ed workshop.
The snow chains must be fi tted only to the front wheels. They
must never be fi tted to "space-saver" type spare wheels.
Take account of the legislation in force in your country on the use
of snow chains and the maximum running speed authorised.

Avoid driving on roads that have been cleared of snow, to
avoid damaging your vehicle's tyres and the road surface. It is
recommended that before you leave, you practise fi tting the snow
chains on a level and dry surface. If your vehicle is fi tted with alloy
wheels, check that no part of the chain or its fi xings is in contact
with the wheel rim.
Original tyre size Maximum link size.
225/45 R18 9 mm


Advice on installation



)
If you have to fi t the chains during a journey, stop the vehicle on a
fl at surface on the side of the road.

)
Apply the parking brake and position any wheel chocks to prevent
movement of your vehicle.

)
Fit the chains following the instructions provided by the
manufacturer.

)
Move off gently and drive for a few moments, without exceeding
30 mph (50 km/h).

)
Stop your vehicle and check that the snow chains are correctly
tightened.