tow PEUGEOT RCZ 2012 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2012, Model line: RCZ, Model: PEUGEOT RCZ 2012Pages: 336, PDF Size: 14.1 MB
Page 148 of 336
146
FUEL TANK
Fuel tank capacity: approximately 55 litres.
LOW FUEL LEVEL
FILLING
When the fuel tank minimum level is reached this warning
lamp comes on on the instrument panel, accompanied by an
audible signal and an alert message. When it fi rst comes on
there remains approximately 5 litres
of fuel in the tank.
Until suffi cient fuel is added, this warning lamp appears every time
the ignition is switched on, accompanied by an audible signal and a
message. When driving, this audible signal and display of the alert
message are repeated with increasing frequency as the fuel level drops
towards "0"
.
Refuel as soon as possible to avoid running out of fuel.
If you run out of fuel (Diesel), refer also to the "Running out of fuel
(Diesel)" section.
A label affi xed to the inside of the fl ap reminds you of the type of fuel to
be used depending on your engine.
Additions of fuel must be of at least 5 litres, in order to be registered by
the fuel gauge. To fi ll the tank in complete safety:
)
the engine must be switched off,
)
press the rear part of the fl ap, then raise it to open it,
)
turn the cap to the left,
)
remove the cap and hook it onto the clip located on the inside of
the fl ap,
)
fi ll the tank, but do not continue after the 3rd cut-off of the
pump
; this could cause malfunctions. Opening the fi ller cap may create a noise a caused by an inrush
of air. This vacuum is entirely normal, resulting from the sealing of
the fuel system.
Page 157 of 336
7/
CHECKS
MANUAL GEARBOX
AUTOMATIC GEARBOX
BRAKE PADS
BRAKE DISC WEAR
The gearbox does not require any maintenance (no oil change).
Refer to the servicing and warranty booklet for the details of
the level checking interval for this component.
The gearbox does not require any maintenance (no oil change).
Refer to the servicing and warranty booklet for details of the
level checking interval for this component.
Brake wear depends on the style of driving, particularly in
the case of vehicles used in town, over short distances.
It may be necessary to have the condition of the brakes
checked, even between vehicle services.
Unless there is a leak in the circuit, a drop in the brake fl uid level
indicates that the brake pads are worn. For information on checking brake disc wear, contact a
PEUGEOT dealer or a qualifi ed workshop.
Only use products recommended by PEUGEOT or products of
equivalent quality and specifi cation.
In order to optimise the operation of units as important as the
braking system, PEUGEOT selects and offers very specifi c
products.
To avoid damaging the electrical units, the use of a high pressure
washer in the engine compartment is strictly prohibited
.
PARKING BRAKE
If excessive travel or a loss of effectiveness of this system
is noticed, the parking brake must be checked, even
between two services.
Checking this system must be done by a PEUGEOT dealer
or a qualifi ed workshop.
Page 162 of 336
160
2. Inflation
)
Turn the selector A
to the "air" position.
)
Uncoil the black pipe H
fully.
)
Connect the black pipe to the valve of the wheel.
As soon as possible, go to a PEUGEOT dealer or a qualifi ed
workshop.
You must inform the technician that you have used this kit. After
inspection, the technician will advise you on whether the tyre can
be repaired or if it must be replaced.
)
Connect the compressor's electric plug to the vehicle's 12 V socket.
)
Start the vehicle again and leave the engine running.
)
Adjust the pressure using the compressor (to infl ate: switch B
in position "I"
; to defl ate: switch B
in position "O"
and press
button C
), in accordance with the vehicle's tyre pressure label
(located on the left hand door aperture).
A loss of pressure indicates that the puncture has not been fully
plugged; contact a PEUGEOT dealer or qualifi ed workshop for
assistance.
)
Remove and stow the kit.
)
Drive at reduced speed (50 mph [80 km/h] max) limiting the
distance travelled to approximately 120 miles (200 km).
Page 163 of 336
8/
PRACTICAL INFORMATION
Beware of discharges of fl uid.
The expiry date of the fl uid is indicated on the cartridge.
The sealant cartridge is designed for single use; even if only partly
used, it must be replaced.
After use, do not discard the cartridge into the environment, take it
to an authorised waste disposal site or a PEUGEOT dealer.
Do not forget to obtain a new sealant cartridge, available from
PEUGEOT dealers or from a qualifi ed workshop.
REMOVING THE CARTRIDGE
)
Stow the black pipe.
)
Detach the angled base from the white pipe.
)
Support the compressor vertically.
)
Unscrew the cartridge from the bottom.
Page 164 of 336
162
CHECKING TYRE PRESSURES / INFLATING
ACCESSORIES
You can also use the compressor, without injecting any product, to:
- check or adjust the pressure of your tyres,
- infl ate other accessories (balls, bicycle tyres...).
)
Turn the selector A
to the "Air" position.
)
Uncoil the black pipe H
fully.
)
Connect the black pipe to the valve of the wheel or
accessory.
If necessary, fi t one of the adaptors supplied with the kit fi rst.
)
Connect the compressor's electrical connector to the vehicle's 12 V
socket.
)
Start the vehicle and let the engine run.
)
Adjust the pressure using the compressor (to infl ate: switch B
in position "I"
; to defl ate: switch B
in position "O"
and press
button C
), according to the vehicle's tyre pressure label or the
accessory's pressure label.
)
Remove the kit then stow it.
Page 168 of 336
166
TOOLS AND SPARE WHEEL *
Depending on the country of sale, the vehicle is equipped with the tools
needed to change a wheel and may also be equipped with a spare
wheel.
The spare wheel is stowed in a protective cover, secured to the boot
fl oor with Velcro
®.
The tools are held in a storage box under the boot fl oor.
Never drive with the rear seat folded when the
spare wheel - or a punctured wheel - is present
in the boot.
Warning marking
"Do not release the backrest of the rear seats!"
*
According to country.
Access to the spare wheel *
)
Open the boot lid.
)
Remove the spare wheel by grasping the grip of its protective
cover.
)
Position the wheel vertically so as to read the warning markings.
)
Remove the Velcro
® located on the tyre tread.
)
Detach the straps, located on each sidewall, then slacken them.
)
Remove the wheel from its protective cover.
When refi tting the wheel into its cover, place it so that the valve is
opposite the strap fi xings.
Page 175 of 336
8/
PRACTICAL INFORMATION
CHANGING A BULB
The headlamps are fi tted with polycarbonate glass with a
protective coating:
)
do not clean them using a dry or abrasive cloth, nor with
a detergent or solvent product,
)
use a sponge and soapy water or a pH neutral product,
)
when using a high pressure washer on persistent marks, do
not keep the lance directed towards the lamps or their edges
for too long, so as not to damage their protective coating and
seals,
)
do not touch the bulb directly with your fi ngers, use lint-free
cloths.
Changing a bulb should only be done after the headlamp has
been switched off for a few minutes (risk of serious burns).
It is imperative to use only anti-ultraviolet (UV) type bulbs in order
not to damage the headlamp.
Always replace a failed bulb with a new bulb with the same type
and specifi cation.
FRONT LAMPS
Model with halogen headlamps
1.
Direction indicators (PY21 W amber).
2.
Dipped beam headlamps (H7 - 55W).
3.
Main beam headlamps (H1 - 55W).
4.
Daytime running lamps / sidelamps (P 21/5 W)
or
Daytime running lamps / sidelamps (LEDs).
Page 180 of 336
178
Changing reversing lamps and foglamps
These two bulbs are changed from outside the rear bumper:
)
unclip the protective cover from the rear, then tilt it,
)
remove it completely to gain access to the two lamp fi xing bolts,
On the left-hand side, take care not to touch the silencer; risk
of burns, if you change the bulb immediately after switching
off the ignition.
)
turn these two bolts one quarter of a turn and remove them,
)
push the lamp towards the inside to unclip it, then tilt it,
)
pull the lamp towards the outside for access to the various
bulb-holders.
- For the reversing lamps: pull the corresponding bulb holder,
- turn the bulb one quarter of a turn and change it.
- For the foglamp: turn the bulb holder one quarter of a turn and
remove it,
- turn the bulb one quarter of a turn and change it.
To refi t, carry out these operations in reverse order.
Page 181 of 336
8/
PRACTICAL INFORMATION
Changing sidelamps and direction indicators
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop.
High pressure washing
When using this type of washing on stubborn dirt, do not persist
on the headlamps, the lamps and their surrounds to avoid
damaging their protective coating and seals.
Changing number plate lamps (W5W)
)
Insert the end of the vehicle's key in the hole in the transparent
cover.
)
Push towards the outside to unclip it.
)
Remove the transparent cover.
)
Pull the bulb out and change it.
Changing the third brake lamp (LEDs)
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop.
Page 189 of 336
8/
PRACTICAL INFORMATION
TOWING A VEHICLE
TOWING EYE
This is stored in the boot under the fl oor.
For access to it:
)
open the boot,
)
raise the fl oor using the strap,
)
secure it in the vertical position beyond the stops, located on the
sides of the boot,
)
remove the towing eye from the storage box.
GENERAL RECOMMENDATIONS
Observe the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of
the towed vehicle.
The person at the wheel of the towed vehicle must have a valid
driving licence.
When towing a vehicle with all four wheels on the ground, always
use an approved towing bar; rope and straps are prohibited.
When towing a vehicle with the engine off, there is no longer any
power assistance for braking or steering.
In the following cases, you must always call on a professional
recovery service:
- vehicle broken down on a motorway or fast road,
- 4 wheel drive vehicle,
- when it is not possible to put the gearbox into neutral, unlock
the steering, or release the parking brake,
- towing with only two wheels on the ground,
- where there is no approved towing bar available...